1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DRAIN BRAKE FLUID
If brake fluid leaks onto any painted surface, immediately wash it off.
3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
28800
4.REMOVE BATTERY
74431
5.REMOVE BATTERY TRAY
74410
6.REMOVE BATTERY CARRIER ASSEMBLY
for 1NZ-FE, 2NZ-FE:
Click hereEngine / Hybrid System>1NZ-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for Automatic Transaxle)>REMOVAL
for 1NR-FE, 2NR-FE:
Click hereEngine / Hybrid System>2NR-FE ENGINE MECHANICAL>ENGINE ASSEMBLY(for CVT)>REMOVAL
44510
7.REMOVE BRAKE ACTUATOR ASSEMBLY (for LHD)
for CVT w/ VSC:
| *a | Lock Lever |
Release the lock lever to disconnect the brake actuator connector.
Be careful not to allow brake fluid to enter the removed connector.
Using a 10 mm and 12 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.
| *a | to Front Wheel Cylinder RH |
| *b | to Front Wheel Cylinder LH |
| *c | to Rear Wheel Cylinder RH |
| *d | to Rear Wheel Cylinder LH |
| *e | from Front Master Cylinder |
| *f | from Rear Master Cylinder |
Use tags or make a memo to identify the places to reconnect the brake tubes.
Remove the 3 bolts and brake actuator assembly with the brake actuator bracket assembly.
Do not damage the brake tubes or wire harness.
Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.
Remove the 3 bolts and No. 1 brake actuator bracket assembly.
for CVT w/ ABS:
| *a | Lock Lever |
Release the lock lever to disconnect the brake actuator connector.
Be careful not to allow brake fluid to enter the removed connector.
Using a 10 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.
| *a | to Front Wheel Cylinder RH |
| *b | to Front Wheel Cylinder LH |
| *c | to Rear Wheel Cylinder RH |
| *d | to Rear Wheel Cylinder LH |
| *e | from Front Master Cylinder |
| *f | from Rear Master Cylinder |
Use tags or make a memo to identify the places to reconnect the brake tubes.
Remove the 3 bolts and brake actuator assembly with the brake actuator bracket assembly.
Do not damage the brake tubes or wire harness.
Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.
Remove the 3 bolts and No. 1 brake actuator bracket assembly.
except CVT w/ VSC:
| *a | Lock Lever |
Release the lock lever to disconnect the brake actuator connector.
Be careful not to allow brake fluid to enter the removed connector.
Using a 10 mm and 12 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.
| *a | to Front Wheel Cylinder RH |
| *b | to Front Wheel Cylinder LH |
| *c | to Rear Wheel Cylinder RH |
| *d | to Rear Wheel Cylinder LH |
| *e | from Front Master Cylinder |
| *f | from Rear Master Cylinder |
Use tags or make a memo to identify the places to reconnect the brake tubes.
Remove the 3 bolts and brake actuator assembly with the brake actuator bracket assembly.
Do not damage the brake tubes or wire harness.
Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.
except CVT w/ ABS:
| *a | Lock Lever |
Release the lock lever to disconnect the brake actuator connector.
Be careful not to allow brake fluid to enter the removed connector.
Using a 10 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.
| *a | to Front Wheel Cylinder RH |
| *b | to Front Wheel Cylinder LH |
| *c | to Rear Wheel Cylinder RH |
| *d | to Rear Wheel Cylinder LH |
| *e | from Front Master Cylinder |
| *f | from Rear Master Cylinder |
Use tags or make a memo to identify the places to reconnect the brake tubes.
Remove the 3 bolts and brake actuator assembly with the brake actuator bracket assembly.
Do not damage the brake tubes or wire harness.
Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.
44510
8.REMOVE BRAKE ACTUATOR ASSEMBLY (for RHD)
| *a | Lock Lever |
Release the lock lever to disconnect the brake actuator connector.
Be careful not to allow brake fluid to enter the removed connector.
Using a 10 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.
| *a | to Front Wheel Cylinder RH |
| *b | to Front Wheel Cylinder LH |
| *c | to Rear Wheel Cylinder RH |
| *d | to Rear Wheel Cylinder LH |
| *e | from Rear Master Cylinder |
| *f | from Front Master Cylinder |
Use tags or make a memo to identify the places to reconnect the brake tubes.
Remove the 3 bolts and brake actuator assembly with the brake actuator bracket assembly.
Do not damage the brake tubes or wire harness.
Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.
44590
9.REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY (for LHD)
for CVT:
Remove the 3 bolts and brake actuator bracket assembly from the brake actuator assembly.
Do not carry the brake actuator assembly by the connector.
except CVT:
Remove the 3 bolts and brake actuator bracket assembly from the brake actuator assembly.
Do not carry the brake actuator assembly by the connector.
44590
10.REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY (for RHD)
Remove the 3 bolts and brake actuator bracket assembly from the brake actuator assembly.
Do not carry the brake actuator assembly by the connector.
44546A
11.REMOVE BRAKE ACTUATOR BRACKET CUSHION
Remove the 3 brake actuator case collars from the 3 brake actuator bracket cushions.
Remove the 3 brake actuator bracket cushions from the brake actuator bracket assembly.