Home › Drivetrain › C54 MANUAL TRANSMISSION / TRANSAXLE › SHIFT AND SELECT LEVER SHAFT(for 1NR-FE) › from 2016.04
RM30M0E _52 Drivetrain _017091 C54 MANUAL TRANSMISSION / TRANSAXLE _0262469 SHIFT AND SELECT LEVER SHAFT(for 1NR-FE) A

C54 MANUAL TRANSMISSION / TRANSAXLE  SHIFT AND SELECT LEVER SHAFT(for 1NR-FE)  REASSEMBLY  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

All disassembled parts should be cleaned before reassembly.

·

Coat all of the sliding and rotating surfaces with gear oil before reassembly, and check that they move smoothly after reassembly.



Hide 33528C 2.INSTALL CONTROL SHAFT COVER OIL SEAL

a.
C295205C01
2.323,1.396 2.677,1.354 false 1.302,0.385 1.51,0.583 0.208,0.198 10 false *a 2.771,1.281 3.229,1.479 0.458,0.198 10 false SST
*a Drive in Depth


Using SST and a hammer, install a new control shaft cover oil seal to the control shaft cover.

SST
09950-60010  (09951-00280)
09950-70010  (09951-07150)

Standard depth:

0 to 0.9 mm (0 to 0.0354 in.)



b.

Coat the lip of the control shaft cover oil seal with MP grease.


Hide 33531B 3.INSTALL SHIFT AND SELECT LEVER SHAFT DUST BOOT

a.
C295203

Install the shift and select lever shaft dust boot to the shift and select lever shaft.


Hide 33528B 4.INSTALL CONTROL SHAFT COVER

a.
C295202

Install the control shaft cover to the shift and select lever shaft.

NOTICE:
·

Do not damage the control shaft cover oil seal.

·

Make sure that the control shaft cover dust boot is securely installed the groove of the shift and select lever shaft and control shaft cover.




Hide 33276H 5.INSTALL NO. 1 SELECT SPRING SEAT SHAFT SNAP RING

a.
C295206

Coat the shift and select lever shaft with gear oil.


b.

Using a brass bar and a hammer, install a new No. 1 select spring seat shaft snap ring to the shift and select lever shaft.


Hide 33256 6.INSTALL SELECT INNER LEVER

a.
C295207C01
3.125,0.833 3.333,1.021 0.208,0.188 10 false *a
*a Drive in Depth


Coat the No. 1 select spring seat with gear oil.


b.

Using a 5 mm pin punch and a hammer, install the No. 1 select spring seat, compression spring, select inner lever and select inner lever slotted spring pin to the shift and select lever shaft.

Driven in depth:

3.0 to 4.0 mm (0.119 to 0.157 in.)



Hide 33251A 7.INSTALL INNER NO. 1 SHIFT LEVER

a.
C295208C01
3,1.031 3.198,1.229 0.198,0.198 10 false *a
*a Drive in Depth


Coat the shift interlock plate and inner No. 1 shift lever with gear oil.


b.

Using a 5 mm pin punch and a hammer, install the shift interlock plate, inner No. 1 shift lever and inner No. 1 shift lever slotted spring pin to the shift and select lever shaft.

Driven in depth:

-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)



Hide 33252A 8.INSTALL INNER NO. 2 SHIFT LEVER

a.
C295209C01
2.979,0.896 3.156,1.094 0.177,0.198 10 false *a
*a Drive in Depth


Coat the inner No. 2 shift lever with gear oil.


b.

Using a 5 mm pin punch and a hammer, install the inner No. 2 shift lever and inner No. 2 shift lever slotted spring pin to the shift and select lever shaft.

Driven in depth:

1.0 to 2.0 mm (0.0394 to 0.0787 in.)



Hide 33277 9.INSTALL NO. 2 SELECT SPRING SEAT

a.
C295210

Coat the No. 2 select spring seat with gear oil.


b.

Install the No. 2 select spring seat and compression spring to the shift and select lever shaft.


c.

Using a brass bar and a hammer, install a new E-ring to the shift and select lever shaft.


Hide 33534F 10.INSTALL NO. 2 SELECTING BELLCRANK BUSH

a.
C295397

Install 2 new No. 2 selecting bellcrank bushes to the selecting bellcrank.


b.

Coat the No. 2 selecting bellcrank bushes with MP grease.


Hide 33558 11.INSTALL NO. 2 SELECTING BELLCRANK DUST COVER

a.
C295396C01
1.698,1.708 2.156,1.958 true 2.219,1.896 2.531,2.094 0.313,0.198 10 false *a
*a Arrow Mark


Install the No. 2 selecting bellcrank dust cover to the selecting bellcrank.

HINT:

Position the arrow mark as shown in the illustration.



Hide 33534E 12.INSTALL NO. 2 SELECTING BELLCRANK

a.
C295395

Install the selecting bellcrank support sub-assembly to the selecting bellcrank.


Hide 33534G 13.INSTALL NO. 2 SELECTING BELLCRANK PLATE WASHER

a.
C295394

Install the No. 2 selecting bellcrank plate washer to the selecting bellcrank support sub-assembly with the washer and nut.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 33557A 14.INSTALL NO. 1 SELECTING BELLCRANK DUST COVER

a.
C295393

Install the No. 1 selecting bellcrank dust cover to the selecting bellcrank.