Home › Engine / Hybrid System › 2NR-FE FUEL › FUEL INJECTOR › from 2016.04
RM30M0E _51 Engine / Hybrid System _053553 2NR-FE FUEL _0265573 FUEL INJECTOR G

2NR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.
A302929C01
0.167,0.125 0.479,0.323 0.313,0.198 10 false *a 1.51,1.094 1.729,1.375 0.219,0.281 14 false 1 1.802,1.094 2.021,1.375 0.219,0.281 14 false 2
*a Component without harness connected
(Fuel Injector Assembly)


Check the resistance.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the fuel injector assembly.



b.

Inspect the fuel injector injection volume.

CAUTION:

Keep the fuel injector assembly away from sparks during the test.


i.
A264971C12
2.656,0.688 2.917,0.271 false 2.01,1.271 2.385,1.594 false 0.885,0.906 1.146,0.531 false 0.573,1.646 0.906,1.885 false 0.938,1.792 1.115,1.969 0.177,0.177 10 false *a 1.198,0.448 1.375,0.625 0.177,0.177 10 false *b 2.448,1.5 2.625,1.677 0.177,0.177 10 false *c 2.979,0.198 3.156,0.375 0.177,0.177 10 false *1
*1 Fuel Pipe (Vehicle Side)
*a SST (Hose)
*b SST (Hose Band)
*c SST (Fuel Tube Connector)


Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)


ii.
A305602C01
0.906,0.135 1.333,0.135 false 1.74,0.323 2.167,0.323 false 0.865,0.75 1.292,0.75 false 2.385,1.104 2.813,1.104 false 1.5,1.021 1.698,1.021 false 0.896,1.969 1.323,1.969 false 1.74,0.969 2.052,1.125 0.313,0.156 10 false *1 0.729,0.052 1.042,0.208 0.313,0.156 10 false *a 2.25,0.25 2.563,0.406 0.313,0.156 10 false *b 0.677,0.656 0.99,0.813 0.313,0.156 10 false *c 2.896,1.031 3.208,1.188 0.313,0.156 10 false *d 0.719,1.885 1.031,2.042 0.313,0.156 10 false *e
*1 O-ring
*a SST (Hose)
*b SST (Hose Band)
*c SST (Adapter)
*d SST (Clamp)
*e Vinyl Tube


Install a new O-ring to the fuel injector assembly.


iii.

Connect SST (adapter and hose) to the fuel injector assembly, and hold the fuel injector assembly and union with SST (clamp).

SST
09268-31014  (09268-41110, 09268-41300, 09268-41700, 95336-08070)


iv.

Install a vinyl tube to the fuel injector assembly.

CAUTION:

Install a suitable vinyl tube to the fuel injector assembly to prevent fuel from spraying.



v.
A264974C10
1.938,0.365 2.469,0.365 false 2.125,1.406 2.49,1.406 false 1.25,0.354 0.76,0.354 false 0.604,0.281 0.792,0.458 0.188,0.177 10 false *a 2.531,0.292 2.719,0.469 0.188,0.177 10 false *b 2.552,1.333 2.74,1.51 0.188,0.177 10 false *c
*a SST (Tie Band)
*b SST (Adapter)
*c SST (Clamp)


Tie SST (clamp) and SST (adapter) together with SST (tie band) as shown in the illustration.

SST
09268-31014  (09268-41110, 09268-41300, 09268-41800)


vi.

Put the fuel injector assembly to a graduated cylinder.



viii.
A264973C10
2.042,0.552 2.042,0.969 false 1.99,1.021 2.146,1.26 0.156,0.24 10 false *a 1.042,1.333 1.198,1.573 0.156,0.24 10 false *b
*a SST (Wire)
*b Connect


Connect SST (wire) to the fuel injector assembly and battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each fuel injector assembly 2 or 3 times.

SST
09842-30080  

NOTICE:

Always switch the voltage on and off at the battery side, not the fuel injector assembly side.


Standard Injection Volume:
Tester Connection Condition Specified Condition
Positive terminal - Ground terminal Per 15 seconds 47 to 57 cc (2.9 to 3.5 cu in.)


Difference between each fuel injector assembly:

10 cc (0.6 cu in.) or less


If the result is not as specified, replace the fuel injector assembly.



c.

Check for fuel drop.

i.

In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel drop from the fuel injector assembly.

Fuel drop:

1 drop or less every 25 minutes


If the result is not as specified, replace the fuel injector assembly.