Home › Drivetrain › C50 MANUAL TRANSMISSION / TRANSAXLE › SHIFT AND SELECT LEVER SHAFT(for 2NR-FE) › from 2016.04
RM30M0E _52 Drivetrain _017090 C50 MANUAL TRANSMISSION / TRANSAXLE _0266929 SHIFT AND SELECT LEVER SHAFT(for 2NR-FE) A

C50 MANUAL TRANSMISSION / TRANSAXLE  SHIFT AND SELECT LEVER SHAFT(for 2NR-FE)  DISASSEMBLY  


PROCEDURE

Hide 33557A 1.REMOVE NO. 1 SELECTING BELLCRANK DUST COVER

a.
C295393

Remove the No. 1 selecting bellcrank dust cover from the selecting bellcrank.


Hide 33534G 2.REMOVE NO. 2 SELECTING BELLCRANK PLATE WASHER

a.
C295394

Remove the nut, washer and No. 2 selecting bellcrank plate washer from the selecting bellcrank support sub-assembly.


Hide 33534E 3.REMOVE NO. 2 SELECTING BELLCRANK

a.
C295395

Remove the No. 2 selecting bellcrank from the selecting bellcrank.


Hide 33558 4.REMOVE NO. 2 SELECTING BELLCRANK DUST COVER

a.
C295396

Remove the No. 2 selecting bellcrank dust cover from the selecting bellcrank.


Hide 33534F 5.REMOVE NO. 2 SELECTING BELLCRANK BUSH

a.
C295397

Remove the 2 No. 2 selecting bellcrank bushes from the selecting bellcrank.


Hide 33277 6.REMOVE NO. 2 SELECT SPRING SEAT

a.
C295197

Fix the shift and select lever shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.


HINT:

Change the positions of the parts fixed in the vise as necessary to allow parts to be removed.



b.

Using a screwdriver, remove the E-ring, No. 2 select spring seat and compression spring from the shift and select lever shaft.


Hide 33252A 7.REMOVE INNER NO. 2 SHIFT LEVER

a.
C295198

Using a 5 mm pin punch and a hammer, remove the inner No. 2 shift lever slotted spring pin and inner No. 2 shift lever from the shift and select lever shaft.

HINT:

Check the orientation of the inner No. 2 shift lever.



Hide 33251A 8.REMOVE INNER NO. 1 SHIFT LEVER

a.
C295199

Using a 5 mm pin punch and a hammer, remove the inner No. 1 shift lever slotted spring pin, inner No. 1 shift lever and shift interlock plate from the shift and select lever shaft.

HINT:

Check the orientation of the inner No. 1 shift lever.



Hide 33256 9.REMOVE SELECT INNER LEVER

a.
C295200

Using a 5 mm pin punch and a hammer, remove the select inner lever slotted spring pin, select inner lever, compression spring and No. 1 select spring seat from the shift and select lever shaft.

HINT:

Check the orientation of the select inner lever.



Hide 33276H 10.REMOVE NO. 1 SELECT SPRING SEAT SHAFT SNAP RING

a.
C295201

Using 2 screwdrivers and a hammer, remove the No. 1 select spring seat shaft snap ring from the shift and select lever shaft.

HINT:

Use a piece of cloth to keep the No. 1 select spring seat shaft snap ring from flying off.



Hide 33528B 11.REMOVE CONTROL SHAFT COVER

a.
C295202

Remove the control shaft cover from the shift and select lever shaft.


Hide 33531B 12.REMOVE SHIFT AND SELECT LEVER SHAFT DUST BOOT

a.
C295203

Remove the shift and select lever shaft dust boot from the shift and select lever shaft.


Hide 33528C 13.REMOVE CONTROL SHAFT COVER OIL SEAL

a.
C295204C01
1.927,0.958 2.573,1.385 true 2.646,1.313 2.958,1.51 0.313,0.198 10 false *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, remove the control shaft cover oil seal from the control shaft cover.

NOTICE:

Make sure not to damage the inside of the control shaft cover.