Home › Drivetrain › CLUTCH › CLUTCH PEDAL(for LHD) › 2016.04–2016.07
RM30M0E _52 Drivetrain _017089 CLUTCH _0091137 CLUTCH PEDAL(for LHD) N

CLUTCH  CLUTCH PEDAL(for LHD)  ADJUSTMENT  


PROCEDURE

Hide 1.INSPECT AND ADJUST CLUTCH PEDAL HEIGHT

a.

Turn back the floor carpet.


b.

Check that the pedal height is correct.

C286913C01
5.635,1.229 5.875,0.875 false 2.177,2.031 2.49,2.188 0.313,0.156 10 false *a 5.906,0.781 6.219,0.938 0.313,0.156 10 false *b 6.156,2.854 6.469,3.01 0.313,0.156 10 false *a
*a Pedal Height from Floor Panel *b Pedal Height Adjust Point
V100144

Measuring Plane of Floor Panel - -


Pedal height from floor panel:
for 1NR-FE, 2NZ-FE:

118.1 to 128.1 mm (4.65 to 5.04 in.)

for 2NR-FE, 1NZ-FE:

133.1 to 143.1 mm (5.25 to 5.63 in.)



c.

If the pedal height is not as specified, adjust it as follows.

i.

Loosen the lock nut and turn the clutch pedal stopper bolt until the correct height is obtained.


ii.

Tighten the lock nut.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)



Hide 2.INSPECT AND ADJUST PEDAL FREE PLAY AND PUSH ROD PLAY

a.
C286914C01
1.135,2.625 1.333,1.99 false 1.073,2.635 1.385,2.792 0.313,0.156 10 false *a 3.094,3.448 3.323,3.635 0.229,0.188 10 false *b 2.844,4.021 3.156,4.177 0.313,0.156 10 false *c
*a Push Rod Play and Free Play Adjust Point
*b Push Rod Play
*c Pedal Free Play


Check that the pedal free play and push rod play are correct.

HINT:

Pay close attention to the change in resistance to distinguish between pedal free play and push rod play while performing the inspection.


i.

Depress the pedal until clutch resistance begins to be felt.

Pedal free play:

5.0 to 15.0 mm (0.197 to 0.590 in.)



ii.

Gently depress the pedal until resistance begins to increase a little.

Push rod play at pedal top:

1.0 to 5.0 mm (0.0394 to 0.196 in.)




b.

If necessary, adjust the pedal free play and push rod play.

HINT:

The push rod play can be adjusted by changing the length of the push rod. Pedal free play changes together with push rod play.


i.

Loosen the lock nut and turn the push rod until the correct pedal free play and push rod play are obtained.

NOTICE:
·

When loosening the lock nut, be sure to hold the clutch master cylinder push rod clevis in place by its square portion.

·

If pedal free play and push rod play are not within the standard range even after adjustment, inspect the related parts.




ii.

Tighten the lock nut.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)

NOTICE:

When tightening the lock nut, be sure to hold the clutch master cylinder push rod clevis in place by its square portion.



iii.

After adjusting the pedal free play and push rod play, check the pedal height.



Hide 3.INSPECT CLUTCH RELEASE POINT

a.
C286915C01
1.719,2.313 2.063,2.427 false 0.792,2.75 1.406,2.323 true 2.094,2.344 2.406,2.5 0.313,0.156 10 false *a 0.635,2.677 0.948,2.833 0.313,0.156 10 false *b 1.396,1.688 1.708,1.844 0.313,0.156 10 false *c 2.177,2.74 2.49,2.896 0.313,0.156 10 false *d
*a Release Point
*b Full Stroke End Position
*c from Pedal Stroke End Position to Release Point
*d Pedal Stroke


Check the release point.

i.

Pull the parking brake lever and install wheel chocks.


ii.

Start the engine and run it at idle.


iii.

Without depressing the clutch pedal, slowly move the shift lever into reverse until the gears contact each other.


iv.

Gradually depress the clutch pedal and measure the stroke distance from the point that the gear noise stops (release point) up to the full stroke end position.

Standard distance:

25 mm (0.984 in.) or more (from pedal stroke end position to release point)


Pedal stroke (Reference):
for 1NR-FE, 2NZ-FE:

120 to 130 mm (4.73 to 5.11 in.)

for 2NR-FE, 1NZ-FE:

137 to 147 mm (5.40 to 5.78 in.)


If the distance is not as specified, perform the following procedure:

·

Check the pedal height.

·

Check the push rod play and pedal free play.

·

Bleed the clutch line.

·

Check the clutch cover and clutch disc.




b.

Install the floor carpet.