Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.07–2017.10
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM D

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  DIAGNOSIS SYSTEM  


M-OBD (EXCEPT EUROPEAN SPEC.)


a.

When troubleshooting Multiplex On-Board Diagnostic (M-OBD) vehicles, the vehicle must be connected to the GTS. Various data output from the ECM can then be read.


b.
C201372

OBD regulations require that the vehicle's on board computer illuminate the MIL on the instrument panel when the computer detects a malfunction in any of the following.

·

The emission control system/components

·

The power train control components (which affect vehicle emissions)

·

The computer

In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are recorded in the ECM memory. If the malfunction does not recur in 3 consecutive trips, the MIL goes off automatically but the DTCs remain recorded in the ECM memory.




EURO-OBD


a.

When troubleshooting Europe On-Board Diagnostic (Euro-OBD) vehicles, the vehicle must be connected to an OBD scan tool (complying with ISO 15765-4). Various data output from the vehicle's ECM can then be read.


b.
F102324

Euro-OBD regulations require that the vehicle's on-board computer illuminate the Malfunction Indicator Lamp (MIL) on the instrument panel when the computer detects a malfunction in any of the following:

·

The emission control system/components

·

The powertrain control components (which affect vehicle emissions)

·

The computer

In addition, the applicable Diagnostic Trouble Codes (DTCs) prescribed by ISO 15765-4 are stored in the ECM memory. If the malfunction does not reoccur in 3 consecutive trips, the MIL turns off automatically but the DTCs remain stored in the ECM memory.



c.

To check DTCs, connect the GTS or OBD scan tool to the Data Link Connector 3 (DLC3) of the vehicle.

The scan tool displays DTCs, the freeze frame data and a variety of engine data.

The DTCs and freeze frame data can be cleared using the scan tool.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



NORMAL MODE AND CHECK MODE (GTS Only)


a.

The diagnosis system operates in normal mode during normal vehicle use. In normal mode, 2-trip detection logic is used to ensure accurate detection of malfunctions. Check mode is also available to technicians as an option. In check mode, 1-trip detection logic is used when reproducing malfunction symptoms for increasing the ability of the system to detect malfunctions, including intermittent malfunctions.



2-TRIP DETECTION LOGIC


a.

When a malfunction is first detected, the malfunction is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected during the subsequent driving cycle, the MIL is illuminated (2nd trip).



FREEZE FRAME DATA


a.

The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not and whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.


b.
C140837E08
0.375,1.74 3.052,1.969 2.677,0.229 10 Freeze frame data which can be read 0.698,0.656 1.281,0.906 0.583,0.25 10 0.5 sec. 1.344,0.656 1.938,0.896 0.594,0.24 10 0.5 sec. 1.969,0.667 2.625,0.885 0.656,0.219 10 0.5 sec. 1.865,0.052 2.917,0.292 1.052,0.24 10 DTC is stored

The GTS displays freeze frame data recorded at five different points: 1) 3 times before the DTC is stored, 2) once when the DTC is stored, and 3) once after the DTC is stored. The data can be used to reproduce the vehicle condition around the time of the malfunction. The data may be helpful in determining the cause of a malfunction. It may also be helpful in determining whether a DTC is being caused by a temporary malfunction.



LIST OF FREEZE FRAME DATA


Powertrain > Engine and ECT
Tester Display
Vehicle Speed
Engine Speed
MAF
Coolant Temp
Throttle Motor DUTY
N Range Status
Starter Signal
Neutral Position SW Signal
Stop Light Switch
A/C Signal
Closed Throttle Position SW
TC and TE1
SPD (NT)
Shift SW Status (P Range)
Shift SW Status (R Range)
Shift SW Status (N Range)
Shift SW Status (N,P Range) Supported
Shift SW Status (N,P Range)
Sports Shift Up SW
Sports Shift Down SW
Sports Mode Selection SW
Shift SW Status (D Range)
A/T Oil Temperature 1
NT Sensor Voltage
SPD (NIN)
SPD (NOUT)
NOUT Sensor Voltage
A/T Oil Pressure
G Sensor
Lock Up
Shift Status
Solenoid (SLS)
SLU Solenoid Status
SL Solenoid Status
Solenoid(SC)
Solenoid(SLP)
G Sensor Calibration
G Sensor Learning Value
CVT Oil Press Calibration

CHECK DATA LINK CONNECTOR 3 (DLC3)




CHECK BATTERY VOLTAGE


Standard Voltage:

11 to 14 V


If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.


MIL (Malfunction Indicator Lamp)


a.

Check that the MIL illuminates when the ignition switch is ON.

If the MIL does not illuminate, check the MIL circuit.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>MIL Circuit


b.

When the engine is started, the MIL turns off.