Home › Drivetrain › K411 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2016.07–2017.10
RM30M0E _52 Drivetrain _052750 K411 CVT _0254682 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K411 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1586  Acceleration Sensor Malfunction  


DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the airbag ECU assembly (yaw rate and acceleration sensor)*1 or deceleration sensor assembly*2. If a malfunction of the airbag ECU assembly (yaw rate and acceleration sensor)*1 or deceleration sensor assembly*2 is determined based on a malfunction signal from the brake actuator assembly (skid control ECU), the ECM stores this DTC.

HINT:
·

The airbag ECU assembly (yaw rate and acceleration sensor) signal is sent to the brake actuator assembly (skid control ECU) via CAN communication.

·

If CAN communication DTCs are output, perform troubleshooting for those DTCs first.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1586 Acceleration Sensor Malfunction After the ignition switch is turned ON, the brake actuator assembly (skid control ECU) has detected either one of the following conditions, and the ECM has received a diagnostic signal from the brake actuator assembly (skid control ECU) for 3 seconds or more (1 trip detection logic).
·

While the vehicle is driven at 30 km/h (19 mph) or more, the difference between the calculated longitudinal G value based on the airbag sensor assembly (yaw rate and acceleration sensor) (G sensor)*1 or deceleration sensor assembly*2 and the value based the vehicle speed exceeds 0.35 G for 60 seconds or more.

·

Airbag sensor assembly (yaw rate and acceleration sensor)*1 or deceleration sensor assembly*2 signal does not change 16 times or more while the vehicle speed decreases from 30 km/h (19 mph) to 0 km/h (0 mph).


·

Airbag ECU assembly (Yaw rate and acceleration sensor)*1

·

Brake actuator assembly (Skid control ECU)*2

·

Deceleration sensor assembly*2

·

CAN communication system


Does not come on DTC stored

*1: w/ VSC

*2: w/o VSC


WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC U0129 is not output A
DTC U0129 is output B



A

2.CHECK DTC OUTPUT (IN ADDITION TO DTC P1586)

B

2.CHECK DTC OUTPUT (IN ADDITION TO DTC P1586)
a.

Connect the GTS to the DLC3.


b.

Turn the GTS on.


c.

Turn the ignition switch to ON.


d.

Clear the DTCs.

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Perform a road test where the vehicle is driven at 30 km/h (19 mph) or more, the brakes are applied at least 16 times and the vehicle is finally stopped.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

g.

Read the DTCs using the GTS.

HINT:

If any DTCs other than P1586 are output, perform troubleshooting for those DTCs first.



Result:
Result Proceed to
Only DTC P1586 is output A
DTC P1586 and other DTCs are output B



A

3.READ VALUE USING GTS (G SENSOR)

B

3.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410

e.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of G sensor Min.: 0 V
Max.: 79.998 V
·

2.31 to 2.69 V: Vehicle on level ground

·

1.88 to 2.5 V: Decelerating

·

2.5 to 3.11 V: Accelerating

·

Stuck at 1.87 V: G sensor malfunction

·

Stuck at 1.87 V: Communication malfunction


-

Result:
Result Proceed to
Data List value is not normal (w/ VSC) A
Data List value is not normal (w/o VSC) B
Data List value is normal C



A

4.REPLACE AIRBAG ECU ASSEMBLY (YAW RATE AND ACCELERATION SENSOR)

B

5.REPLACE DECELERATION SENSOR

C

4.REPLACE AIRBAG ECU ASSEMBLY (YAW RATE AND ACCELERATION SENSOR)
a.

Replace the airbag ECU assembly (yaw rate and acceleration sensor).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>COMPONENTS


Result:
Proceed to
NEXT



NEXT

5.REPLACE DECELERATION SENSOR

Result:
Proceed to
NEXT



NEXT