Home › Engine / Hybrid System › 1NZ-FE ENGINE MECHANICAL › REAR CRANKSHAFT OIL SEAL › 2016.07–2016.10
RM30M0E _51 Engine / Hybrid System _017073 1NZ-FE ENGINE MECHANICAL _0091004 REAR CRANKSHAFT OIL SEAL A

1NZ-FE ENGINE MECHANICAL  REAR CRANKSHAFT OIL SEAL  INSTALLATION  


PROCEDURE

Hide 11401L 1.INSTALL REAR ENGINE OIL SEAL

a.

Apply MP grease to the lip of a new rear engine oil seal.

NOTICE:

Keep the lip free of foreign matter.



b.
A166929E04
2.896,1.76 2.688,1.604 false 1.125,2.719 1.24,2.448 false 2.729,1.802 3.021,1.948 0.292,0.146 10 false SST 1.115,2.01 2.073,2.198 0.958,0.188 10 false 0 to -1.0 mm 1.281,2.354 1.74,2.552 0.458,0.198 10 false SST

Using SST and hammer, tap in the rear engine oil seal until its surface is flush with the cylinder block sub-assembly and oil pan sub-assembly.

SST
09223-56010  

Rear engine oil seal tap in depth:

0 to -1.0 mm (0 to -0.04 in.)


NOTICE:
·

Do not tap the oil pump seal at an angle.

·

Wipe off extra grease from the crankshaft.




Hide 32101 2.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A166739E01
2.63,1.619 2.935,1.773 0.304,0.155 10 SST 1.954,2.054 2.592,1.726 false

Using SST, hold the crankshaft damper sub-assembly.

SST
09960-10010  (09962-01000, 09963-01000)


b.
A248257C03
1.094,1.719 1.26,1.396 false 2.083,1.854 1.771,1.854 false 2.24,1.083 2.625,1.448 false 0.927,1.667 1.094,1.833 0.167,0.167 10 *1 2.115,1.792 2.281,1.958 0.167,0.167 10 *2 2.646,1.427 2.813,1.594 0.167,0.167 10 *3
*1 Front Drive Plate Spacer (Reversible)
*2 Drive Plate and Ring Gear Sub-assembly
*3 Rear Drive Plate Spacer
V100135

Engine Side
V100136

Transaxle Side


Install the front drive plate spacer, drive plate and ring gear sub-assembly, and rear drive plate spacer to the crankshaft.

NOTICE:

As the drive plate and ring gear sub-assembly and rear drive plate spacer are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.


HINT:

The front drive plate spacer is reversible.



c.

Clean the 6 bolts and their holes.


d.
A192239C40
1.781,0.552 1.542,1.385 false 1.823,0.458 2,0.615 0.177,0.156 10 false *a
*a Adhesive


Apply adhesive to 2 or 3 threads at the end of each of the 6 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



e.
A158035E06
1.823,0.542 1.927,0.698 0.104,0.156 10 1 1.833,1.51 1.948,1.677 0.115,0.167 10 2 2.229,0.781 2.385,0.958 0.156,0.177 10 3 1.417,1.271 1.573,1.427 0.156,0.156 10 4 2.24,1.292 2.406,1.458 0.167,0.167 10 5 1.385,0.792 1.552,0.969 0.167,0.177 10 6

Install and uniformly tighten the 6 bolts in several steps, in the sequence shown in the illustration.

Torque:
88 N*m (897 kgf*cm, 65 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installing the drive plate and ring gear sub-assembly.