Home › Engine / Hybrid System › 2NR-FE ENGINE CONTROL › SFI SYSTEM › 2016.07–2017.10
RM30M0E _51 Engine / Hybrid System _053304 2NR-FE ENGINE CONTROL _0258353 SFI SYSTEM U

2NR-FE ENGINE CONTROL  SFI SYSTEM  TERMINALS OF ECM  


A382280C01
0.625,0.25 1.125,0.5 0.5,0.25 1.99,0.25 2.49,0.5 0.5,0.25 3.375,0.25 3.875,0.5 0.5,0.25 4.708,0.25 5.208,0.5 0.5,0.25 5.99,0.25 6.49,0.5 0.5,0.25 4.708,2 5.208,2.25 0.5,0.25 3.375,2 3.875,2.25 0.5,0.25 1.99,2 2.49,2.25 0.5,0.25 0.625,2 1.125,2.25 0.5,0.25 0.083,0.167 0.604,0.438 0.521,0.271 12 false *A 0.083,1.917 0.583,2.25 0.5,0.333 12 false *B 0.75,0.281 1.208,0.479 0.458,0.198 10 false B46 2.115,0.281 2.573,0.479 0.458,0.198 10 false B47 3.51,0.281 3.969,0.479 0.458,0.198 10 false B48 4.813,0.281 5.271,0.479 0.458,0.198 10 false F130 6.083,0.281 6.542,0.479 0.458,0.198 10 false F131 0.75,2.031 1.208,2.229 0.458,0.198 10 false B46 2.115,2.031 2.573,2.229 0.458,0.198 10 false B47 3.479,2.031 3.938,2.229 0.458,0.198 10 false F130 4.813,2.031 5.271,2.229 0.458,0.198 10 false F131
*A for CVT *B for Manual Transaxle


HINT:

The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


Terminal No. Wiring Color Terminal Description Condition Specified Condition
B46-5 (+BM) - B46-3 (E1) R - W-B Power source of ECM Always 11 to 14 V
B46-6 (M-) - B46-4 (ME01) BR - W-B Throttle actuator operation signal (negative terminal) Idling with warm engine Pulse generation
(See waveform 1)
B46-7 (M+) - B46-4 (ME01) G - W-B Throttle actuator operation signal (positive terminal) Idling with warm engine Pulse generation
(See waveform 2)
B46-8 (OE1-) - B46-9 (OE1+) W - L Camshaft timing oil control valve assembly operation signal (for exhaust camshaft) Idling Pulse generation
(See waveform 3)
B46-10 (OC1-) - B46-11 (OC1+) BR - GR Camshaft timing oil control valve assembly operation signal (for intake camshaft) Idling Pulse generation
(See waveform 4)
B46-13 (IGT4) - B46-3 (E1) SB - W-B Ignition coil assembly (ignition signal) Idling Pulse generation
(See waveform 5)
B46-14 (IGT3) - B46-3 (E1) G - W-B
B46-15 (IGT2) - B46-3 (E1) Y - W-B
B46-16 (IGT1) - B46-3 (E1) B - W-B
B46-18 (VTA2) - B46-28 (ETA) GR - V Throttle position sensor signal (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 2.1 to 3.1 V
Ignition switch ON, accelerator pedal fully depressed 4.6 to 5.0 V
B46-21 (VCV1) - B46-3 (E1) R - W-B Power source of camshaft position sensor (for intake camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
B46-22 (VV1-) - B46-23 (VV1+) P - V Camshaft position sensor signal (for intake camshaft) Idling with warm engine Pulse generation
(See waveform 6)
B46-24 (EV1+) - B46-32 (EV1-) GR - G Camshaft position sensor signal (for exhaust camshaft) Idling with warm engine Pulse generation
(See waveform 6)
B46-33 (VCNE) - B46-3 (E1) Y - W-B Power source of crankshaft position sensor Ignition switch ON 4.5 to 5.5 V
B46-27 (NE+) - B46-34 (NE-) P - B Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 7)
B46-29 (VCTA) - B46-28 (ETA) W - V Power source of throttle position sensor (specific voltage) Ignition switch ON 4.5 to 5.5 V
B46-30 (VTA1) - B46-28 (ETA) Y - V Throttle position sensor signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 3.2 to 4.8 V
B46-31 (VCE1) - B46-3 (E1) L - W-B Power source of camshaft position sensor (for exhaust camshaft) (specific voltage) Ignition switch ON 4.5 to 5.5 V
B47-1 (#40) - B46-1 (E01)
B47-2 (#30) - B46-1 (E01)
B47-3 (#20) - B46-1 (E01)
B47-4 (#10) - B46-1 (E01)
W - W-B
Y - W-B
P - W-B
LG - W-B
Fuel injector assembly signal Ignition switch ON 11 to 14 V
Idling Pulse generation
(See waveform 8)
B47-6 (HA1A) - B47-5 (E04) R - W-B Air fuel ratio sensor heater operation signal Idling Pulse generation
(See waveform 9)
Ignition switch ON 11 to 14 V
B47-7 (HT1B) - B47-5 (E04) P - W-B Heated oxygen sensor heater operation signal Idling Below 3.0 V
Ignition switch ON 11 to 14 V
B47-8 (EMPS) - B46-3 (E1) B - W-B Power steering ECU Idling (When Steering wheel is turned to some degree) Below 3.0 V
Idling (Steering wheel is neutral) 11 to 14 V
B47-13 (PRG) - B46-1 (E01) BR - W-B Purge VSV operation signal Ignition switch ON 11 to 14 V
Idling, under purge control Pulse generation
(See waveform 10)
B47-15 (NSW)*2 - B46-3 (E1) W - W-B Park/neutral position switch signal Ignition switch ON, shift lever not in P or N 11 to 14 V
Ignition switch ON, shift lever in P or N Below 3.0 V
B47-16 (LIN) - B46-3 (E1) LG - W-B Generator Ignition switch ON 11 to 14 V
B47-17 (STA) - B46-3 (E1) G - W-B Starter signal Cranking 5.5 V or higher
B47-20 (KNK1) - B47-28 (EKNK) R - G Knock sensor signal Engine speed maintained at 4000 rpm after warming up engine Pulse generation
(See waveform 11)
B47-22 (THW) - B47-30 (ETHW) V - L Engine coolant temperature sensor signal Idling, engine coolant temperature 80°C (176°F) 0.2 to 1.0 V
B47-23 (THA) - B47-31 (ETHA) P - BR Intake air temperature sensor signal Idling, Intake air temperature 20°C (68°F) 0.5 to 3.4 V
B47-24 (VG) - B47-32 (E2G) V - SB Mass air flow meter signal Idling, shift lever in P or N (neutral), A/C switch off*5 0.5 to 3.0 V
B47-26 (A1A+) - B46-3 (E1) B - W-B Air fuel ratio sensor signal Always (Ignition switch ON) 3.3 V*1
B47-27 (OX1B) - B47-35 (EX1B) GR - R Heated oxygen sensor signal Engine speed maintained 2500 rpm for 2 minutes after warming up sensor Pulse generation
(See waveform 12)
B47-34 (A1A-) - B46-3 (E1) W - W-B Air fuel ratio sensor signal Always (Ignition switch ON) 2.9 V*1
B47-14 (PBV)*2 - B46-3 (E1) GR - W-B Brake ejector VSV operation signal Ignition switch ON 11 to 14 V
F130-5 (FC) - B46-3 (E1) LG - W-B Fuel pump control Engine stopped and ignition switch ON (fuel pump does not operate) 11 to 14 V
Engine stopped and ignition switch ON (fuel pump operates) Below 1.5 V
F130-6 (MREL) - B46-3 (E1) L - W-B EFI relay operation signal Ignition switch ON 11 to 14 V
F130-8 (R)*2 - B46-3 (E1) GR - W-B R shift position switch signal Ignition switch ON and shift lever in R 11 to 14 V
Ignition switch ON and shift lever not in R Below 1 V
F130-11 (TACH) - B46-3 (E1) R - W-B Engine speed signal Idling Pulse generation
(See waveform 13)
F130-12 (ACMG)*5 - B46-3 (E1) BE - W-B Magnet clutch relay All of the following conditions are met:
·

Engine running

·

Blower switch set : Lo*6

·

Blower switch set : 1*7

·

A/C switch off


11 to 14 V
All of the following conditions are met:
·

Engine running

·

Blower switch set : Lo*6

·

Blower switch set : 1*7

·

A/C switch ON (magnet clutch ON)


0 to 3.0 V
F131-30 (AC1)*5 - B46-3 (E1) L - W-B Magnet clutch request signal All of the following conditions are met:
·

Engine running

·

Blower switch set : Lo*6

·

Blower switch set : 1*7

·

A/C switch ON (magnet clutch ON)


11 to 14 V
All of the following conditions are met:
·

Engine running

·

Blower switch set : Lo*6

·

Blower switch set : 1*7

·

A/C switch ON (magnet clutch ON)


0 to 3.0 V
F130-13 (CANH) - B46-3 (E1) BE - W-B CAN communication line Ignition switch ON Pulse generation
(See waveform 14)
F130-14 (CANL) - B46-3 (E1) W - W-B CAN communication line Ignition switch ON Pulse generation
(See waveform 15)
F130-18 (D)*2 - B46-3 (E1) L - W-B D shift position switch signal Ignition switch ON and shift lever in D 11 to 14 V
Ignition switch ON and shift lever not in D Below 1 V
F130-18 (D)*3, *8 - B46-3 (E1) G - W-B No. 2 clutch start switch signal Ignition switch ON, clutch pedal fully depressed Below 1 V
Ignition switch ON, clutch pedal fully released 11 to 14 V
F130-23 (SPD) - B46-3 (E1) BR - W-B Vehicle speed signal from combination meter assembly Driving at 20 km/h (12 mph) Pulse generation
(See waveform 16)
F130-26 (PB) - F130-35 (EPB) L - BE Vacuum sensor signal Idling with warm engine, brake pedal released 1.5 to 2.0 V
F130-27 (VCPB) - F130-35 (EPB) V - BE Power source of vacuum sensor (for PB) Ignition switch ON 4.75 to 5.25 V
F130-25 (HAC) - F130-34 (EHAC) G - V Atmospheric pressure sensor signal
·

Ignition switch ON

·

Absolute pressure of 40 kPa (0.4 kgf/cm2, 5.8 psi) applied to atmospheric pressure sensor


1.6 to 2.0 V
·

Ignition switch ON

·

Absolute pressure of 60 kPa (0.6 kgf/cm2, 8.7 psi) applied to atmospheric pressure sensor


2.2 to 2.6 V
·

Ignition switch ON

·

Atmospheric pressure applied to atmospheric pressure sensor


3.4 to 3.8 V
F130-33 (VHAC) - F130-34 (EHAC) GR - V Atmospheric pressure sensor power supply
·

Ignition switch ON

·

Engine stopped


4.5 to 5.5 V
F130-17 (ELS1) - B46-3 (E1) V - W-B Electric load Tail light switch on 7.5 to 14 V
Tail light switch off Below 1.5 V
F130-28 (ELS2) - B46-3 (E1) B - W-B Electric load Defogger switch on 7.5 to 14 V
Defogger switch off Below 1.5 V
F131-1 (+B) - B46-3 (E1) R - W-B Power source of ECM Ignition switch ON 11 to 14 V
F131-2 (+B2) - B46-3 (E1) R - W-B Power source of ECM Ignition switch ON 11 to 14 V
F131-3 (BATT) - B46-3 (E1) G - W-B Battery (for measuring battery voltage and for ECM memory) Always 11 to 14 V
F131-5 (FANL) - B46-3 (E1) BR - W-B Cooling fan relay (FAN NO. 1 relay)
·

Ignition switch ON

·

Cooling fan not operated


11 to 14 V
·

Idling with A/C on*5 or high engine coolant temperature

·

Cooling fan operated


Below 1.5 V
F131-6 (FANH) - B46-3 (E1) LG - W-B No. 2 cooling fan relay (FAN NO. 2 relay)
·

Idling with high engine coolant temperature

·

Cooling fan operated at high speed


Below 1.5 V
F131-16 (NEO)*4 - B46-3 (E1) BE - W-B Crankshaft position sensor signal Idling with warm engine Pulse generation
(See waveform 17)
F131-8 (IGSW) - B46-3 (E1) V - W-B Ignition or starter switch assembly Ignition switch ON 11 to 14 V
F131-10 (STP) - B46-3 (E1) B - W-B Stop light switch assembly Brake pedal depressed 7.5 to 14 V
Brake pedal released Below 1.5 V
F131-11 (ST1-) - B46-3 (E1) G - W-B Stop light switch assembly Ignition switch ON, Brake pedal depressed Below 1.5 V
Ignition switch ON, Brake pedal released 7.5 to 14 V
F131-18 (EC) - Body ground W-B - - Ground Always Below 1 Ω
F131-19 (TC) - B46-3 (E1) L - W-B Terminal TC of DLC3 Ignition switch ON 11 to 14 V
F131-20 (VCPA) - F131-27 (EPA) G - BR Power source of accelerator pedal position sensor (for VPA) Ignition switch ON 4.5 to 5.5 V
F131-22 (VCP2) - F131-29 (EPA2) W - B Power source of accelerator pedal rod assembly (for VPA2) Ignition switch ON 4.5 to 5.5 V
F131-26 (VPA) - F131-27 (EPA) P - BR Accelerator pedal rod assembly signal (for engine control) Ignition switch ON, accelerator pedal fully released 0.5 to 1.1 V
Ignition switch ON, accelerator pedal fully depressed 2.6 to 4.5 V
F131-28 (VPA2) - F131-29 (EPA2) L - B Accelerator pedal rod assembly signal (for sensor malfunction detection) Ignition switch ON, accelerator pedal fully released 1.2 to 2.0 V
Ignition switch ON, accelerator pedal fully depressed 3.4 to 4.75 V
B46-1 (E01) - Body ground W-B - - Ground Always Below 1 Ω
B46-2 (E02) - Body ground W-B - - Ground Always Below 1 Ω
B46-3 (E1) - Body ground W-B - - Ground Always Below 1 Ω
B46-4 (ME01) - Body ground W-B - - Ground Always Below 1 Ω
B47-5 (E04) - Body ground W-B - - Ground Always Below 1 Ω
F131-18 (EC) - Body ground W-B - - Ground Always Below 1 Ω

*1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

*2: for CVT

*3: w/ Cruise Control System

*4: w/ Theft Deterrent System

*5: w/ Air Conditioning System

*6: for Automatic air conditioning system

*7: for Manual air conditioning system

*8: for Manual Transaxle


WAVEFORM 1


A245848E53
2.849,0.99 3.182,1.142 0.333,0.151 10 GND 2.627,0.266 3.166,0.409 0.539,0.142 10 5 V/DIV. 0.479,0.626 0.664,0.777 0.184,0.15 10 M- 1.323,1.82 1.996,1.967 0.672,0.147 10 1 ms./DIV.

Throttle Actuator Negative Terminal Signal
ECM Terminal Name Between M- and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 2


A208000E59
2.856,0.973 3.187,1.119 0.331,0.147 10 GND 2.631,0.216 3.176,0.36 0.545,0.144 10 5 V/DIV. 0.501,0.616 0.722,0.759 0.221,0.143 10 M+ 1.323,1.806 1.995,1.965 0.672,0.159 10 1 ms./DIV.

Throttle Actuator Positive Terminal Signal
ECM Terminal Name Between M+ and ME01
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling with warm engine

HINT:

The duty ratio varies depending on the throttle actuator operation.



WAVEFORM 3


A283575E08
0.604,0.26 1.563,0.573 0.958,0.313 10 5 V/DIV. 0.51,1.115 1.021,1.375 0.51,0.26 10 GND 1.729,1.844 2.583,2.063 0.854,0.219 10 1 ms./DIV.

Camshaft Timing Oil Control Valve Assembly (for Exhaust Camshaft) Signal
ECM Terminal Name Between OE1+ and OE1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 4


A283575E09
0.604,0.26 1.563,0.573 0.958,0.313 10 false 5 V/DIV. 0.51,1.125 1.021,1.385 0.51,0.26 10 false GND 1.729,1.844 2.583,2.063 0.854,0.219 10 false 1 ms./DIV.

Camshaft Timing Oil Control Valve Assembly (for Intake Camshaft) Signal
ECM Terminal Name Between OC1+ and OC1-
Tester Range 5 V/DIV., 1 ms./DIV.
Condition Idling


WAVEFORM 5


A247851E02
3.031,0.938 3.375,1.094 0.344,0.156 10 false GND

Igniter Signal (IGT signal)
ECM Terminal Name Between IGT (1 to 4) and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 6


A255508E31
0.104,0.073 0.844,0.344 0.74,0.271 10 5 V/DIV. 0.156,0.719 0.5,0.917 0.344,0.198 10 CH1 0.156,1.5 0.479,1.698 0.323,0.198 10 CH2 0.115,0.865 0.552,1.104 0.438,0.24 10 (VV1) 0.115,1.646 0.521,1.854 0.406,0.208 10 (EV1) 3.042,0.813 3.396,1.063 0.354,0.25 10 GND 3.052,1.583 3.385,1.854 0.333,0.271 10 GND 1.313,1.865 2.177,2.073 0.865,0.208 10 20 ms./DIV.

Camshaft Position Sensor Signal (for Intake and Exhaust Camshaft)
ECM Terminal Name CH1: Between VV1+ and VV1-
CH2: Between EV1+ and EV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 7


A200774E19
3,1.177 3.344,1.354 0.344,0.177 10 false GND 0.042,0 0.604,0.167 0.563,0.167 10 false 2 V/DIV. 1.115,1.833 2.281,2.031 1.167,0.198 10 false 20 ms./DIV.

Crankshaft Position Sensor Signal
ECM Terminal Name Between NE+ and NE-
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 8


A287799E12
0.646,1.563 1.104,1.76 0.458,0.198 10 false GND 0.396,0.115 1.063,0.344 0.667,0.229 10 false 20 V/DIV. 1.833,1.896 2.646,2.083 0.813,0.188 10 false 20 ms./DIV.

Fuel Injector Assembly Injection Signal
ECM Terminal Name Between #10 (to #40) and E01
Tester Range 20 V/DIV., 20 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the engine speed increases.



WAVEFORM 9


A205412E20
2.594,0.063 3.208,0.375 0.615,0.313 10 5 V/DIV. 2.688,0.896 3.104,1.24 0.417,0.344 10 GND 1.219,1.854 1.979,2.031 0.76,0.177 10 10 ms./DIV.

Air Fuel Ratio Sensor Heater Operation Signal
ECM Terminal Name Between HA1A and E04
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling with warm engine

HINT:

The wavelength varies in accordance with the engine operating condition.



WAVEFORM 10


A205411E16
2.604,0.25 3.229,0.406 0.625,0.156 10 false 10 V/DIV. 1.104,1.906 1.865,2.083 0.76,0.177 10 false 20 ms./DIV. 2.677,1.031 3.042,1.208 0.365,0.177 10 false GND

Purge VSV Signal
ECM Terminal Name Between PRG and E01
Tester Range 10 V/DIV., 20 ms./DIV.
Condition Idling, under purge control

HINT:

If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



WAVEFORM 11


A283572E18
2.427,0.521 3.208,0.865 0.781,0.344 10 1 V/DIV. 2.615,1 3.115,1.292 0.5,0.292 10 GND 1.115,1.865 2.01,2.083 0.896,0.219 10 1 ms./DIV.

Knock Sensor Signal
ECM Terminal Name Between KNK1 and EKNK
Tester Range 1 V/DIV., 1 ms./DIV.
Condition Engine speed maintained at 4000 rpm after warming up engine

HINT:
·

The wavelength becomes shorter as engine speed increases.

·

The waveforms and amplitudes displayed differ slightly depending on the vehicle.




WAVEFORM 12


A283571E09
0.51,0.219 1.292,0.521 0.781,0.302 10 0.2 V/DIV. 0.573,1.479 1.021,1.76 0.448,0.281 10 GND 1.802,1.875 2.771,2.115 0.969,0.24 10 200 ms./DIV.

Heated Oxygen Sensor Signal
ECM Terminal Name Between OX1B and EX1B
Tester Range 0.2 V/DIV., 200 ms./DIV.
Condition Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

HINT:

In the Data List, the items O2S B1S2 show the ECM input values of the heated oxygen sensor.



WAVEFORM 13


A283574E06
0.438,0.313 1.167,0.625 0.729,0.313 10 5 V/DIV. 0.448,1.177 0.896,1.458 0.448,0.281 10 GND 1.688,1.885 2.708,2.104 1.021,0.219 10 10 ms./DIV.

Engine speed signal
ECM Terminal Name Between TACH and E1
Tester Range 5 V/DIV., 10 ms./DIV.
Condition Idling

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 14


A283576E07
2.75,0.292 3.354,0.583 0.604,0.292 10 1 V/DIV. 3.01,1.396 3.344,1.708 0.333,0.313 10 GND 1.604,1.896 2.479,2.125 0.875,0.229 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANH and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 15


A283577E06
2.76,0.271 3.375,0.531 0.615,0.26 10 1 V/DIV. 3.01,1.365 3.375,1.604 0.365,0.24 10 GND 1.625,1.865 2.583,2.052 0.958,0.188 10 10 μs./DIV.

CAN Communication Signal (Reference)
ECM Terminal Name Between CANL and E1
Tester Range 1 V/DIV., 10 μs./DIV.
Condition Ignition switch ON

HINT:

The waveform varies depending on the CAN communication signal.



WAVEFORM 16


A283573E14
2.677,0.125 3.354,0.385 0.677,0.26 10 false 2 V/DIV. 2.833,1.229 3.25,1.531 0.417,0.302 10 false GND 1.156,1.99 2.219,2.167 1.063,0.177 10 false 20 ms./DIV.

Vehicle Speed Signal
ECM Terminal Name Between SPD and E1
Tester Range 2 V/DIV., 20 ms./DIV.
Condition Driving at 20 km/h (12 mph)

HINT:

The wavelength becomes shorter as the vehicle speed increases.



WAVEFORM 17


A301717E03
2.875,0.125 3.427,0.323 0.552,0.198 10 false 5 V/DIV. 1.469,1.99 2.156,2.156 0.688,0.167 10 false 2 ms./DIV. 3.104,1.677 3.427,1.875 0.323,0.198 10 false GND

Crankshaft Position Sensor Signal
ECM Terminal Name Between NEO and E1
Tester Range 5 V/DIV., 2 ms./DIV.
Condition Idling with warm engine