Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2016.07
RM30M0E _53 Suspension _057557 TIRE PRESSURE MONITORING _0280386 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198/98  Initialization Switch (for Test Mode DTC)  


DESCRIPTION

During test mode, when the tire pressure warning reset switch is on, the tire pressure warning light comes on and when the tire pressure warning reset switch is off, the tire pressure warning light blinks at 0.125 second intervals.

DTC No. Detection Item DTC Detection Condition Trouble Area
C2198/98 Initialization Switch (for Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning reset switch

·

Harness or connector

·

Tire pressure warning ECU and receiver



WIRING DIAGRAM

C349074E02
2.448,1.552 3.875,2.073 1.427,0.521 10 false Tire Pressure Warning Reset Switch 2.448,1.385 3.063,1.583 0.615,0.198 10 false F135 5.104,2.406 6.531,2.938 1.427,0.531 10 false Tire Pressure Warning ECU and Receiver 5.104,2.24 5.719,2.438 0.615,0.198 10 false F134 5.344,1 5.958,1.198 0.615,0.198 10 false CLSW 5.104,0.906 5.26,1.104 0.156,0.198 10 false 7 3.74,0.906 3.896,1.104 0.156,0.198 10 false 1 2.438,0.906 2.594,1.104 0.156,0.198 10 false 2 2.656,0.896 2.865,1.135 0.208,0.24 10 false E 3.417,0.896 3.719,1.125 0.302,0.229 10 false INT

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT TIRE PRESSURE WARNING RESET SWITCH
a.

Remove the tire pressure warning reset switch.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RESET SWITCH>REMOVAL


b.

Inspect the tire pressure warning reset switch.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RESET SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - TIRE PRESSURE WARNING RESET SWITCH)

NG

REPLACE TIRE PRESSURE WARNING RESET SWITCH

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - TIRE PRESSURE WARNING RESET SWITCH)
a.

Disconnect the F134 tire pressure warning ECU and receiver connector.


b.

Disconnect the F135 tire pressure warning reset switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F134-7 (CLSW) - F135-1 (INT) Always Below 1 Ω
F134-7 (CLSW) or F135-1 (INT) - Body ground Always 10 kΩ or higher
F135-2 (E) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for Sedan) A
OK (for Hatchback) B
NG C



A

REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR