Home › Drivetrain › U340E AUTOMATIC TRANSMISSION / TRANSAXLE › VALVE BODY ASSEMBLY › 2016.07–2016.10
RM30M0E _52 Drivetrain _017087 U340E AUTOMATIC TRANSMISSION / TRANSAXLE _0090608 VALVE BODY ASSEMBLY A

U340E AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY  REMOVAL  


PROCEDURE

Hide 2.DRAIN AUTOMATIC TRANSAXLE FLUID

a.

Using a 10 mm hexagon socket wrench, remove the drain plug sub-assembly and gasket from the automatic transaxle oil pan sub-assembly, and drain the ATF.


b.

Using a 10 mm hexagon socket wrench, install a new gasket and drain plug sub-assembly to the automatic transaxle oil pan sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 35106D 3.REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

C282685

a.

Remove the 19 bolts, automatic transaxle oil pan sub-assembly and automatic transaxle oil pan gasket from the automatic transaxle case sub-assembly.

NOTICE:

Some fluid will remain in the automatic transaxle oil pan sub-assembly. Remove all the bolts, and carefully remove the automatic transaxle oil pan sub-assembly.



Hide 35394 4.REMOVE TRANSMISSION OIL CLEANER MAGNET

a.
C282686

Remove the 2 transmission oil cleaner magnets from the automatic transaxle oil pan sub-assembly.


b.
C283249

Examine the particles in the automatic transaxle oil pan sub-assembly.

i.

Collect any steel chips using the removed transmission oil cleaner magnets.

Carefully inspect the foreign matter and particles in the automatic transaxle oil pan sub-assembly and on the transmission oil cleaner magnets to see the type of wear which might be found in the automatic transaxle assembly.

Steel (magnetic): bearing, gear and clutch plate wear

Brass (non-magnetic): bushing wear



Hide 35330 5.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

C282687

a.

Remove the 3 bolts and valve body oil strainer assembly from the transmission valve body assembly.

NOTICE:

Perform the operation carefully as some fluid will come out from the valve body oil strainer assembly.



b.
C282688

Remove the oil strainer O-ring from the valve body oil strainer assembly.


Hide 82125J 6.DISCONNECT TRANSMISSION WIRE

a.
C282689C01
1.396,1.271 1.615,0.99 true 1.646,0.833 1.844,1.01 0.198,0.177 10 true *1
*1 Temperature Sensor Clamp


Remove the bolt and the temperature sensor clamp and separate the transmission wire from the transmission valve body assembly.


b.

Disconnect the 5 connectors from the transmission valve body assembly.


Hide 35410 7.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.
C282690C01
2.208,0.792 2.802,0.573 true 2.229,1.219 2.792,1.427 true 2.844,0.458 3.156,0.656 0.313,0.198 10 false *1 2.823,1.333 3.135,1.531 0.313,0.198 10 false *2
*1 Manual Detent Spring Sub-assembly
*2 Manual Detent Spring Cover


Remove the 2 bolts, manual detent spring cover and the manual detent spring sub-assembly from the transmission valve body assembly.


b.
C282691

Remove the 13 bolts and transmission valve body assembly from the automatic transaxle case sub-assembly.

NOTICE:

Do not drop the check ball body, check ball body compression spring or accumulator pistons.



Hide 35251 8.REMOVE CHECK BALL BODY

a.
C282389C02
1.125,1.885 1.615,1.698 true 1.677,1.969 2.083,1.969 false 0.969,1.792 1.281,1.948 0.313,0.156 10 false *1 2.115,1.875 2.427,2.031 0.313,0.156 10 false *2
*1 Check Ball Body Compression Spring
*2 Check Ball Body


Remove the check ball body and check ball body compression spring from the automatic transaxle case sub-assembly.


Hide 35145C 9.REMOVE TRANSAXLE CASE GASKET

a.
C288060

Remove the transaxle case gasket from the automatic transaxle case sub-assembly.


Hide 35149B 10.REMOVE TRANSAXLE CASE 2ND BRAKE GASKET

a.
C288061

Remove the transaxle case 2nd brake gasket from the automatic transaxle case sub-assembly.