Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.07–2016.10
RM30M0E _57 Power Source / Network _017152 NETWORKING _0084784 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Air Conditioning Amplifier Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Air Conditioning Amplifier Communication Stop Mode Either condition is met:
·

"Air Conditioning Amplifier" is not displayed on the CAN Bus Check screen of the GTS

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "Air Conditioning Amplifier Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

Air conditioning amplifier assembly branch line or connector

·

Power source circuit of air conditioning amplifier assembly

·

Air conditioning amplifier assembly ground circuit

·

Air conditioning amplifier assembly



WIRING DIAGRAM

for LHD


E340823E03
2.75,1.208 3.417,0.292 3.417,0.292 3.583,0.292 false 0.104,0.073 1.021,0.271 0.917,0.198 10 false V Bus: 2.146,0.458 2.76,0.656 0.615,0.198 10 false DLC3 6.219,2.125 6.99,2.323 0.771,0.198 10 false 120 Ω 0.792,2.125 1.563,2.323 0.771,0.198 10 false 120 Ω 3.656,0.219 4.115,0.417 0.458,0.198 10 false F62 3.656,0.385 6.073,0.719 2.417,0.333 10 false No. 1 CAN Junction Connector 0.302,2.74 3.365,2.938 3.063,0.198 10 false F81*1, F82*2, F130*3 0.302,2.906 0.917,3.104 0.615,0.198 10 false ECM 5.844,2.75 6.302,2.948 0.458,0.198 10 false F38 5.844,2.917 7.052,3.333 1.208,0.417 10 false Combination Meter Assembly 4.063,3.281 4.375,3.479 0.313,0.198 10 false 11 4.625,3.281 4.938,3.479 0.313,0.198 10 false 12 3.875,3.51 4.792,3.708 0.917,0.198 10 false TX+ 4.448,3.51 5.365,3.708 0.917,0.198 10 false TX- 3.531,3.781 3.99,3.979 0.458,0.198 10 false IG+ 4.5,3.781 4.958,3.979 0.458,0.198 10 false GND 4.958,3.667 5.271,3.865 0.313,0.198 10 false 14 3.313,3.667 3.625,3.865 0.313,0.198 10 false 1 2.5,3.927 4.333,4.125 1.833,0.198 10 false ECU-IG NO. 1 0.479,3.76 2.313,4.302 1.833,0.542 10 false from Ignition or Starter Switch Assembly*4 or No. 1 Ignition Relay*5 3.354,4.271 5.042,4.469 1.688,0.198 10 false F3*6, F124*7 3.365,4.438 4.927,4.854 1.563,0.417 10 false Air Conditioning Amplifier Assembly 5.938,3.844 6.906,4.26 0.969,0.417 10 false Trouble Area 0.167,5.25 3.073,5.594 2.906,0.344 10 false *1: for 2NZ-FE with Manual Transaxle 0.167,5.667 3.479,6.167 3.313,0.5 10 false *2: for Automatic Transaxle 0.156,6.073 3.469,6.573 3.313,0.5 10 false *3: for 1NR-FE or 2NR-FE 0.167,6.5 3.479,7 3.313,0.5 10 false *4: w/o Smart Entry and Start System 3.667,5.25 6.979,5.75 3.313,0.5 10 false *5: w/ Smart Entry and Start System 3.667,5.667 6.979,6.167 3.313,0.5 10 false *6: for Automatic Air Conditioning System 3.667,6.083 6.875,6.5 3.208,0.417 10 false *7: for Manual Air Conditioning System with 1NR-FE or for Manual Air Conditioning System with 2NR-FE 1.229,6.917 3.458,7.167 2.229,0.25 10 false : CAN Main Bus Line (CANH) 4.375,6.917 6.604,7.167 2.229,0.25 10 false : CAN Branch Line (CANH) 4.375,7.333 6.604,7.583 2.229,0.25 10 false : CAN Branch Line (CANL) 1.229,7.333 3.458,7.583 2.229,0.25 10 false : CAN Main Bus Line (CANL)


for RHD


E340824E05
2.917,1.26 3.75,0.167 3.75,0.167 3.917,0.167 false 4.5,1.26 4.885,0.76 4.885,0.76 5.052,0.76 false 0.104,0.073 3.01,0.271 2.906,0.198 10 false V Bus: 2.302,0.5 2.917,0.698 0.615,0.198 10 false DLC3 3.99,0.094 4.448,0.292 0.458,0.198 10 false F62 3.99,0.26 6.063,0.531 2.073,0.271 10 false No. 1 CAN Junction Connector 5.125,0.854 7.063,1.26 1.938,0.406 10 false No. 2 CAN Junction Connector 5.125,0.688 5.583,0.885 0.458,0.198 10 false F71 0.792,2.167 1.563,2.365 0.771,0.198 10 false 120 Ω 6.208,2.167 6.979,2.365 0.771,0.198 10 false 120 Ω 0.781,2.802 1.396,3 0.615,0.198 10 false F130 0.781,2.969 1.24,3.167 0.458,0.198 10 false ECM 3.677,3.615 3.99,3.813 0.313,0.198 10 false 11 4.073,3.615 4.385,3.813 0.313,0.198 10 false 12 3.49,3.844 3.948,4.042 0.458,0.198 10 false TX+ 3.885,3.844 4.344,4.042 0.458,0.198 10 false TX- 4.135,4.281 4.594,4.479 0.458,0.198 10 false GND 3.167,3.99 3.625,4.188 0.458,0.198 10 false IG+ 1.969,4.135 3.802,4.333 1.833,0.198 10 false ECU-IG NO. 1 2.938,3.885 3.25,4.083 0.313,0.198 10 false 1 4.583,4.177 4.896,4.375 0.313,0.198 10 false 14 0.74,4.406 2.99,4.865 2.25,0.458 10 false from Ignition or Starter Switch Assembly*1 or No. 1 Ignition Relay*2 5.823,2.792 6.438,2.99 0.615,0.198 10 false F38 5.823,2.958 7.031,3.406 1.208,0.448 10 false Combination Meter Assembly 5.333,4.073 6.542,4.521 1.208,0.448 10 false Trouble Area 0.313,5.333 5.813,5.531 5.5,0.198 10 false *1: w/o Smart Entry and Start System 0.313,5.656 5.813,5.854 5.5,0.198 10 false *2: w/ Smart Entry and Start System 1.208,5.958 5.188,6.156 3.979,0.198 10 false : CAN Main Bus Line (CANH) 4.354,5.958 7.156,6.24 2.802,0.281 10 false : CAN Branch Line (CANH) 4.354,6.365 7.156,6.646 2.802,0.281 10 false : CAN Branch Line (CANL) 1.208,6.365 4.01,6.646 2.802,0.281 10 false : CAN Main Bus Line (CANL) 2.979,4.75 5.167,5.115 2.188,0.365 10 false Air Conditioning Amplifier Assembly 2.969,4.604 3.427,4.802 0.458,0.198 10 false F124


CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 20 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
for Automatic Air Conditioning System A
for Manual Air Conditioning System with 1NR-FE or for Manual Air Conditioning System with 2NR-FE B



A

2.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)

B

4.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)
2.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
E221291C16
1.5,0.25 1.917,0.5 0.417,0.25 1.771,1.24 1.552,1.771 true 1.917,1.229 2.104,1.75 true 1.625,0.302 1.865,0.531 0.24,0.229 10 false F3 0.073,0.052 0.281,0.26 0.208,0.208 10 false *a 1.406,1.802 1.656,2.031 0.25,0.229 10 false TX+ 2.031,1.792 2.281,2.021 0.25,0.229 10 false TX-
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-11 (TX+) - F3-12 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
E221291C17
1.5,0.25 1.917,0.5 0.417,0.25 0.458,1.24 0.156,1.771 true 2.177,1.24 2.417,1.76 true 1.625,0.302 1.865,0.531 0.24,0.229 10 false F3 0.073,0.052 0.281,0.26 0.208,0.208 10 false *a 0.031,1.802 0.313,2.031 0.281,0.229 10 false IG+ 2.302,1.792 2.656,2.042 0.354,0.25 10 false GND
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F3-14 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F3-1 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

4.CHECK FOR OPEN IN CAN BUS LINES (AIR CONDITIONING AMPLIFIER ASSEMBLY BRANCH LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
E221291C49
1.5,0.25 1.917,0.5 0.417,0.25 1.771,1.24 1.552,1.771 true 1.917,1.229 2.104,1.75 true 1.563,0.302 1.885,0.531 0.323,0.229 10 false F124 0.073,0.052 0.281,0.26 0.208,0.208 10 false *a 1.406,1.802 1.656,2.031 0.25,0.229 10 false TX+ 2.031,1.792 2.281,2.021 0.25,0.229 10 false TX-
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Disconnect the air conditioning amplifier assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F124-11 (TX+) - F124-12 (TX-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BRANCH LINE OR CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
E221291C50
1.5,0.25 1.917,0.5 0.417,0.25 0.458,1.24 0.156,1.771 true 2.177,1.24 2.417,1.76 true 1.552,0.302 1.99,0.531 0.438,0.229 10 false F124 0.073,0.052 0.281,0.26 0.208,0.208 10 false *a 0.031,1.802 0.313,2.031 0.281,0.229 10 false IG+ 2.302,1.792 2.656,2.042 0.354,0.25 10 false GND
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F124-14 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Connect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F124-1 (IG+) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)