Home › Engine / Hybrid System › 1NZ-FE COOLING › RADIATOR › 2016.07–2016.10
RM30M0E _51 Engine / Hybrid System _017081 1NZ-FE COOLING _0090207 RADIATOR A

1NZ-FE COOLING  RADIATOR  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

Be sure that the ignition switch is off if you work near the electric cooling fans or radiator grille. With the ignition switch ON, the electric cooling fans may automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.


PROCEDURE

Hide 81150 1.REMOVE HEADLIGHT ASSEMBLY LH

Hide 81150 2.REMOVE HEADLIGHT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 53215B 6.REMOVE HOOD LOCK SUPPORT

A300055

a.

Disengage the clamp to disconnect the wire harness from the hood lock support.


b.

Remove the 2 bolts and hood lock support from the radiator support assembly.


Hide 53216A 7.REMOVE UPPER RADIATOR SUPPORT

a.
A304789

Disengage the clamp to separate the hood lock control cable assembly from the upper radiator support.


b.
A304785

Disengage the 2 clamps to disconnect the wire harness from the upper radiator support.


c.
A300057

Disconnect the low pitched horn assembly connector.


d.
A302891

Remove the 4 bolts and upper radiator support from the radiator support assembly.


Hide 16750 8.REMOVE FAN SHROUD VENTILATION DUCT ASSEMBLY

a.
A307871

Disengage the 2 claws and 2 guides to remove the fan shroud ventilation duct assembly from the radiator assembly.


Hide 9.DISCONNECT RADIATOR RESERVOIR TANK HOSE

A302892

a.

Disconnect the radiator reservoir tank hose from the water filler sub-assembly.


Hide 16573B 10.DISCONNECT NO. 3 RADIATOR HOSE

A302925

a.

Loosen the hose clip and disconnect the No. 3 radiator hose from the radiator assembly.


Hide 16572D 11.DISCONNECT NO. 2 RADIATOR HOSE

A300058

a.

Loosen the hose clip and disconnect the No. 2 radiator hose from the radiator assembly.


Hide 32942 12.DISCONNECT OUTLET NO. 1 OIL COOLER HOSE

A302915

a.

Loosen the hose clip and disconnect the outlet No. 1 oil cooler hose from the radiator assembly.


Hide 32941 13.DISCONNECT INLET NO. 1 OIL COOLER HOSE

A302916

a.

Loosen the hose clip and disconnect the inlet No. 1 oil cooler hose from the radiator assembly.


Hide 16400 14.REMOVE RADIATOR ASSEMBLY

A302947

a.

Disconnect the cooling fan motor connector.


b.

Disengage the 3 clamps to disconnect the wire harness from the fan shroud.


c.
A302893

Disengage the 2 claws and 2 guides to separate the cooler condenser assembly from the radiator assembly.

HINT:

While tilting the cooler condenser assembly toward the front of the vehicle, separate the cooler condenser assembly from the radiator assembly.



d.

Remove the radiator assembly together with fan shroud from the vehicle.

NOTICE:

Do not apply excessive force to the cooler condenser assembly or piping when removing the radiator assembly.



Hide 16711 15.REMOVE FAN SHROUD

a.
A302894

Disengage the 2 claws and 2 guides to remove the fan shroud from the radiator assembly.


Hide 16561 16.REMOVE NO. 1 RADIATOR TO SUPPORT SEAL

HINT:

This procedure is only performed when replacing the No. 1 radiator to support seal with a new one.


a.
A350118

Remove the No. 1 radiator to support seal from the fan shroud.


Hide 16523A 17.REMOVE RADIATOR SUPPORT CUSHION

A104900

a.

Remove the 2 radiator support cushions from the radiator assembly.


Hide 16535 18.REMOVE LOWER RADIATOR SUPPORT

A104901

a.

Remove the 2 lower radiator supports from the radiator assembly.


Hide 19.REMOVE RADIATOR DRAIN COCK PLUG

A106592

a.

Remove the radiator drain cock plug from the radiator assembly.

NOTICE:

Replace the O-ring if it is damaged.