Home › Engine / Hybrid System › 2NZ-FE LUBRICATION › OIL AND OIL FILTER › 2016.07–2016.10
RM30M0E _51 Engine / Hybrid System _017084 2NZ-FE LUBRICATION _0091243 OIL AND OIL FILTER A

2NZ-FE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. Used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Take precautions when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Wear protective clothing and gloves that cannot be penetrated by oil. Wash skin with soap and water, or use waterless hand cleaner, to completely remove any used engine oil. Do not use gasoline, thinner, or solvents.

·

Dispose of used oil and used oil filters at designated disposal sites in order to preserve the environment.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.

Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.


b.

Remove the oil pan drain plug and gasket from the No. 2 oil pan sub-assembly, and drain the engine oil into a container.


c.

Clean and install the oil pan drain plug with a new gasket to the No. 2 oil pan sub-assembly.

Torque:
37.5 N*m (382 kgf*cm, 28 ft.*lbf)


Hide 15601 2.REMOVE OIL FILTER SUB-ASSEMBLY

a.
A248714E03
1.885,0.865 2.823,0.76 true 2.896,0.677 3.208,0.844 0.313,0.167 10 false SST

Using SST, remove the oil filter sub-assembly from the oil filter union.

SST
09228-06501  


Hide 15601 3.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Clean the oil filter sub-assembly installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter sub-assembly.


c.
A248715E02
2.885,0.792 2.448,0.927 true 2.906,0.708 3.208,0.875 0.302,0.167 10 false SST

Lightly screw the oil filter sub-assembly into place by hand. Tighten oil filter sub-assembly until the gasket contacts the seat.


d.

Using SST, tighten the oil filter sub-assembly.

SST
09228-06501  

i.

Depending on the work space available, choose from the following.

·

If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.

Torque:

13 N*m (133 kgf*cm, 10 ft.*lbf)



·

If enough space is not available to use a torque wrench, tighten the oil filter sub-assembly a 3/4 turn by hand or use a standard wrench.




Hide 4.ADD ENGINE OIL

a.

Add fresh engine oil.

Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)
API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil
·

5W-30


·

10W-30


API grade SL, SM or SN multigrade engine oil
·

15W-40


·

20W-50




Standard Oil Capacity:
Item Capacity
Drain and refill with oil filter change 3.7 liters (3.9 US qts, 3.3 Imp. qts)
Drain and refill without oil filter change 3.4 liters (3.6 US qts, 3.0 Imp. qts)
Dry fill 4.1 liters (4.3 US qts, 3.6 Imp. qts)



b.

Install the oil filler cap sub-assembly to the cylinder head cover sub-assembly.


Hide 5.INSPECT FOR ENGINE OIL LEAK

a.

Start the engine. Make sure that there are no engine oil leaks from the area that was worked on.