Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/o Smart Entry and Start System) › 2016.07–2016.10
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090852 IMMOBILISER SYSTEM(w/o Smart Entry and Start System) J

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/o Smart Entry and Start System)  Engine does not Start because No Initial Combustion  


DESCRIPTION

·

If an error in transponder key ECU assembly occurs, this symptom may occur.


CAUTION / NOTICE / HINT

NOTICE:

If the transponder key ECU assembly or key is replaced, refer to Service Bulletin.


PROCEDURE

1.CLEAR DTC
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Body Electrical > Immobiliser > Clear DTCs
50002 260

Result:
Proceed to
NEXT



NEXT

2.CHECK FOR DTC
2.CHECK FOR DTC
a.

Check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>IMMOBILISER SYSTEM(w/o Smart Entry and Start System)>DTC CHECK / CLEAR

Body Electrical > Immobiliser > Trouble Codes
50001 260
Powertrain > Engine and ECT > Trouble Codes
50001 234
HINT:

Before checking for DTCs, perform the "DTC Output Confirmation Operation" procedure.



Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)

B

3.READ VALUE USING GTS (IMMOBILISER FUEL CUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Immobiliser Fuel Cut
50003 234 505

e.

Perform the Data List according to the display on the GTS.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Immobiliser Fuel Cut Status of immobiliser system fuel cut ON or OFF - -
OK:

OFF is displayed after the engine is started



Result:
Result Proceed to
OK (for 1NZ-FE) A
OK (for 2NZ-FE with Automatic Transaxle) B
OK (for 2NZ-FE with Manual Transaxle) C
OK (for 1NR-FE) D
OK (for 2NR-FE) E
NG F



A

B

C

D

E

F

4.CHECK SECURITY INDICATOR LIGHT OPERATION
4.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

Check that the security indicator light turns off when a registered key is inserted into the ignition key cylinder.

OK:

Security indicator light turns OFF



Result:
Proceed to
OK
NG



OK

NG

5.CHECK SECURITY INDICATOR LIGHT OPERATION
5.CHECK SECURITY INDICATOR LIGHT OPERATION
a.

Check that the security indicator light turns off when another registered key is inserted into the ignition key cylinder.

OK:

Security indicator light turns OFF



Result:
Proceed to
OK
NG



OK

6.CHECK WHETHER ENGINE STARTS

NG

7.REPLACE TRANSPONDER KEY ECU ASSEMBLY
6.CHECK WHETHER ENGINE STARTS
a.

Using another registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally



Result:
Proceed to
OK
NG



OK

11.REPLACE KEY

NG

7.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.REGISTER KEY
8.REGISTER KEY
a.

Register the key.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

9.REGISTER ECU COMMUNICATION ID
9.REGISTER ECU COMMUNICATION ID
a.

Register the ECU communication ID.

HINT:

Refer to Service Bulletin.


Result:
Proceed to
NEXT




NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

11.REPLACE KEY
11.REPLACE KEY
a.

Replace the key.

NOTICE:

Key ID code registration is necessary when replacing the key.

Refer to Service Bulletin.



Result:
Proceed to
NEXT



NEXT

12.CHECK WHETHER ENGINE STARTS
12.CHECK WHETHER ENGINE STARTS
a.

Using a registered key, turn the ignition switch to ON.


b.

Check that the engine starts 5 seconds after the ignition switch was turned to ON.

OK:

Engine starts normally



Result:
Result Proceed to
OK A
NG (for 1NZ-FE) B
NG (for 2NZ-FE with Automatic Transaxle) C
NG (for 2NZ-FE with Manual Transaxle) D
NG (for 1NR-FE) E
NG (for 2NR-FE) F



A

END (KEY WAS DEFECTIVE)

B

C

D

E

F