Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.07–2016.10
RM30M0E _58 Vehicle Interior _017115 SUPPLEMENTAL RESTRAINT SYSTEMS _0084736 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.

DTCs are displayed by blinking of the SRS warning light.

HINT:
·

When each warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.

·

A DTC output mode signal is transmitted through the CAN communication system to each ECU including the airbag ECU assembly. Thus when all systems do not enter DTC output mode, there may be an ECM malfunction.



WIRING DIAGRAM

C352197E04
0.219,0.51 3.146,0.76 2.927,0.25 10 false *1: for Automatic Transaxle 0.219,0.875 3.146,1.125 2.927,0.25 10 false *2: for 2NZ-FE with Manual Transaxle 0.219,1.26 3.146,1.51 2.927,0.25 10 false *3: for 1NR-FE 0.219,1.646 3.146,1.896 2.927,0.25 10 false *4: for 2NR-FE 0.938,4.417 3.865,4.667 2.927,0.25 10 false : CAN Communication Line 4.052,1.01 4.75,1.229 0.698,0.219 10 false 6*2 4.052,1.177 4.75,1.396 0.698,0.219 10 false 19*3, *4 3.781,1.281 4.115,1.479 0.333,0.198 10 false TC 3.417,1.604 4.115,1.823 0.698,0.219 10 false F83*1 3.417,1.781 4.115,2 0.698,0.219 10 false F81*2 3.417,2.104 3.75,2.302 0.333,0.198 10 false ECM 3.24,3.198 3.573,3.396 0.333,0.198 10 false 4 3.427,3.344 3.76,3.542 0.333,0.198 10 false CG 3.781,3.323 4.115,3.521 0.333,0.198 10 false TC 4.052,3.198 4.385,3.396 0.333,0.198 10 false 13 3.406,3.719 3.74,3.917 0.333,0.198 10 false F16 3.396,3.896 3.833,4.104 0.438,0.208 10 false DLC3 5.479,3.865 6.927,4.094 1.448,0.229 10 false Airbag ECU Assembly 3.417,1.948 4.115,2.167 0.698,0.219 10 false F131*3, *4 4.052,0.844 4.75,1.063 0.698,0.219 10 false 23*1

PROCEDURE

1.CHECK WIRE HARNESS (TC OF DLC3 - TC OF ECM)
a.

Turn the ignition switch off.


b.

Disconnect the connector from the ECM.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-13 (TC) - F81-6 (TC)*1 Always Below 1 Ω
F16-13 (TC) - F83-23 (TC)*2 Always Below 1 Ω
F16-13 (TC) - F131-19 (TC)*3, *4 Always Below 1 Ω


*1: for Automatic Transaxle

*2: for 2NZ-FE with Manual Transaxle

*3: for 1NR-FE

*4: for 2NR-FE



Result:
Proceed to
OK
NG



OK

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)

NG

REPLACE WIRE HARNESS

2.CHECK WIRE HARNESS (CG OF DLC3 - BODY GROUND)
a.
C204945C12
0.083,0.49 0.604,0.813 0.521,0.323 1.646,0.792 1.802,0.302 true 0.052,0.063 0.198,0.208 0.146,0.146 10 false *1 1.844,0.208 2.167,0.406 0.323,0.198 10 false CG 0.198,0.563 0.458,0.719 0.26,0.156 10 false F16
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)

NG

REPLACE WIRE HARNESS

3.CHECK WIRE HARNESS (TC OF DLC3 - BODY GROUND)
a.
C204945C13
0.135,0.521 0.563,0.771 0.427,0.25 2.01,1.854 1.833,1.344 true 0.156,0.135 0.302,0.281 0.146,0.146 10 false *1 2.042,1.771 2.333,1.969 0.292,0.198 10 false TC 0.208,0.563 0.51,0.75 0.302,0.188 10 false F16
*1 DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F16-13 (TC) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPLACE WIRE HARNESS OR EACH ECU