Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › IMMOBILISER SYSTEM(w/ Smart Entry and Start System) › 2016.07–2016.10
RM30M0E _58 Vehicle Interior _017111 THEFT DETERRENT / KEYLESS ENTRY _0090851 IMMOBILISER SYSTEM(w/ Smart Entry and Start System) U

THEFT DETERRENT / KEYLESS ENTRY  IMMOBILISER SYSTEM(w/ Smart Entry and Start System)  TERMINALS OF ECU  


CHECK ENGINE SWITCH


B271001E13
3.354,0.229 3.729,0.458 0.375,0.229 3.417,0.271 4.073,0.635 0.656,0.365 10 false F13

a.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F13-6 (AGND) - Body ground - G - Body ground Transponder key amplifier ground Always Below 1 Ω -
F13-7 (TXCT) - F13-6 (AGND) Input R - G Immobiliser communication input Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
F13-8 (CODE) - F13-6 (AGND) Output W - G Immobiliser communication output Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -
F13-10 (VC5) - F13-6 (AGND) Input SB - G Transponder key amplifier power supply Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V -

*1: for Automatic Transaxle and CVT

*2: for Manual Transaxle



b.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F13-7 (TXCT) - F13-6 (AGND) Input R - G Signal input from certification ECU (smart key ECU assembly)
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response

HINT:

If immobiliser key code verification communication is not performed correctly, the malfunction may be indicated by one or more of the Data List items listed above



F13-8 (CODE) - F13-6 (AGND) Output W - G Signal output to certification ECU (smart key ECU assembly)
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Engine switch off, engine switch pressed with key held near engine switch*1 Pulse generation
(See waveform 2)
F13-10 (VC5) - F13-6 (AGND) Input SB - G Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)

If the result is not as specified, the engine switch may be malfunctioning.

HINT:

*1: Remove the key battery before performing this inspection.



c.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N18
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F13-7 (TXCT) - F13-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
E291614N04
2.781,1 3.24,1.198 0.458,0.198 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F13-8 (CODE) - F13-6 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, engine switch pressed with key held near engine switch*1

HINT:

*1: Remove the key battery before performing this inspection.



iii.
B216007N05
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection F13-10 (VC5) - F13-6 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed




CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


B333750E02
2.427,0.385 2.865,0.667 0.438,0.281 4.094,0.385 4.531,0.667 0.438,0.281 2.542,0.438 3,0.635 0.458,0.198 10 false F43 4.188,0.448 4.646,0.646 0.458,0.198 10 false F44

a.

Disconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


b.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F43-1 (+B) - F43-10 (E) Input B - W-B*1, *2
V - W-B*3
+B power supply Always 11 to 14 V -
F44-33 (CUTB) - F43-10 (E) Input L - W-B Stand-by power Always 11 to 14 V -
F43-10 (E) - Body ground - W-B - Body ground Ground Always Below 1 Ω -

*1: for Hatchback

*2: for Sedan with 1NZ-FE or for Sedan with 2NZ-FE

*3: for Sedan with 1NR-FE or for Sedan with 2NR-FE



c.

Reconnect the F43 and F44 certification ECU (smart key ECU assembly) connectors.


d.

Measure the resistance and voltage according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F43-15 (IND) - F43-10 (E) Output P - W-B Security indicator output Engine switch off → on (IG) Pulse generation
→ Below 2 V
-
F44-2 (TXCT) - F43-24 (AGND) Output R - G Signal output to transponder key amplifier Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


F44-1 (CODE) - F43-24 (AGND) Input W - G Signal input from transponder key amplifier Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
F44-20 (VC5) - F43-24 (AGND) Output SB - G Transponder key amplifier power supply Engine switch off, brake pedal*1 or clutch pedal*2 not depressed, 30 seconds or more elapsed after driver door opened and then closed Below 1 V
F43-24 (AGND) - Body ground - G - Body ground Transponder key amplifier ground Always Below 1 Ω

*1: for Automatic Transaxle and CVT

*2: for Manual Transaxle



e.

Check for pulses according to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F44-2 (TXCT) - F43-24 (AGND) Output R - G Signal output to transponder key amplifier
(Code sent from certification ECU (smart key ECU assembly) to transponder key amplifier built into engine switch, and then transmitted by transponder key amplifier antenna as radio waves)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 1)
·

BCC Malfunction

·

Abnormal Status

·

Different Encrypt Code

·

Different Serial Number

·

Frame Error

·

Response


F44-1 (CODE) - F43-24 (AGND) Input W - G Signal input from transponder key amplifier
(Radio waves from transponder key amplifier built into engine switch used to detect key information. Key information then sent to certification ECU (smart key ECU assembly))
Engine switch off, engine switch pressed with key held near engine switch*1 Pulse generation
(See waveform 2)
F44-20 (VC5) - F43-24 (AGND) Output SB - G Transponder key amplifier power supply
(Power supplied from certification ECU (smart key ECU assembly) when transponder key amplifier built into engine switch activated)
Engine switch off, key not in cabin, within 30 seconds after engine switch pressed Pulse generation
(See waveform 3)
F43-3 (EFII) - F43-24 (AGND) Input BR - G EFI communication input
(Signal input from ECM to certification ECU (smart key ECU assembly))
Engine switch off 11 to 14 V
·

B2799

·

B279A

·

Engine Start Request

·

EFI Code Receive


F43-3 (EFII) - F43-24 (AGND) Input BR - G EFI communication input
(Signal input from ECM to certification ECU (smart key ECU assembly))
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 4)
F44-35 (EFIO) - F43-24 (AGND) Output G - G EFI communication output
(Signal output from certification ECU (smart key ECU assembly) to ECM)
Engine switch off Below 1 V
F44-35 (EFIO) - F43-24 (AGND) Output G - G EFI communication output
(Signal output from certification ECU (smart key ECU assembly) to ECM)
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 5)

If the result is not as specified, the certification ECU (smart key ECU assembly) may be malfunctioning.

HINT:

*1: Remove the key battery before performing this inspection.



f.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
B051052N19
2.802,0.781 3.156,0.969 0.354,0.188 10 GND

Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F44-2 (TXCT) - F43-24 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


ii.
E291614N05
2.781,1 3.24,1.198 0.458,0.198 10 false GND

Waveform 2 (Reference)

Measurement Condition
Item Content
Tester Connection F44-1 (CODE) - F43-24 (AGND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Engine switch off, engine switch pressed with key held near engine switch*1

HINT:

*1: Remove the key battery before performing this inspection.



iii.
B216007N06
2.885,1.031 3.427,1.375 0.542,0.344 10 GND

Waveform 3 (Reference)

Measurement Condition
Item Content
Tester Connection F44-20 (VC5) - F43-24 (AGND)
Tool Setting 2 V/DIV., 200 ms./DIV.
Condition Engine switch off, key not in cabin, within 30 seconds after engine switch pressed


iv.

Waveform 4 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F43-3 (EFII) - F43-24 (AGND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


v.

Waveform 5 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F44-35 (EFIO) - F43-24 (AGND)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected




CHECK STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)


B118684E91
3.458,0.188 3.833,0.406 0.375,0.219 3.531,0.208 3.854,0.375 0.323,0.167 10 false F15

a.

Measure the voltage resistance and check for pulses to the value(s) in the table below.

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
F15-1 (GND) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F15-3 (IGE) - F15-1 (GND) Input GR - W-B Steering lock motor operation permission signal (motor operation permission signal supplied by certification ECU (smart key ECU assembly)) Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P*1

·

Key carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off


Pulse generation
(See waveform 1)
·

Power Supply Short

·

Unlock Request Receive

·

Lock Request Receive


F15-4 (SLP1) - F15-1 (GND) Output L - W-B*2
B - W-B*3
Steering lock bar position signal (signal output from steering unlock sensor) Steering locked → unlocked*2 11 to 14 V → Below 1.5 V
·

Push Start Error

·

Sensor Value


F15-6 (IG2) - F15-1 (GND) Input V - W-B IG signal (IG2 power supply input for steering lock motor) Engine switch off → on (IG) Below 1 V → 11 to 14 V B2788
F15-7 (B) - Body ground Output P - Body ground Constant power supply Always 11 to 14 V B2788

*1: for Automatic Transaxle and CVT

*2: for 1NZ-FE or for 2NZ-FE

*3: for 1NR-FE or for 2NR-FE


If the result is not as specified, the steering lock ECU (steering lock actuator assembly) may be malfunctioning.

HINT:

*2: The steering locks when any door is opened with the shift lever in P*1 and the engine switch off. The steering unlocks when the engine switch is turned on (ACC).



b.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.
C259594C03
1.052,0.344 2.958,0.219 2.958,0.219 2.521,0.396 true 2.031,1.802 2.292,1.969 true 3.01,0.135 3.323,0.292 0.313,0.156 10 *a 2.344,1.938 2.667,2.104 0.323,0.167 10 *b 2.938,1.594 3.302,1.792 0.365,0.198 10 GND
*a Steering lock motor not operating
*b Steering lock motor operating


Waveform 1 (Reference)

Measurement Condition
Item Content
Tester Connection F15-3 (IGE) - F15-1 (GND)
Tool Setting 2 V/DIV., 20 ms./DIV.
Condition Steering lock motor operates when both conditions met, and then door opened:
·

Shift lever in P*1

·

Key carried, engine switch turned on (IG), steering unlocked, and then engine switch turned off



*1: for Automatic Transaxle and CVT





CHECK ECM (for Automatic Transaxle)


A301712E02
5.385,0.292 5.75,0.531 0.365,0.24 4.094,0.281 4.458,0.521 0.365,0.24 2.646,0.292 3.01,0.531 0.365,0.24 1.281,0.292 1.646,0.531 0.365,0.24 5.438,0.333 5.896,0.531 0.458,0.198 10 false F83 4.146,0.323 4.604,0.521 0.458,0.198 10 false F82 2.698,0.323 3.156,0.521 0.458,0.198 10 false B31 1.323,0.323 1.781,0.521 0.458,0.198 10 false B29

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
B29-1 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F83-4 (BATT) - B29-1 (E1) Input G - W-B +B power supply Always 11 to 14 V -
F83-1 (+B) - B29-1 (E1) Input R - W-B +B power supply Engine switch on (IG) 11 to 14 V -
F83-2 (+B2) - B29-1 (E1) Input R - W-B +B power supply Engine switch on (IG) 11 to 14 V -
F82-15 (IMO) - B29-1 (E1) Output BR - W-B Certification ECU (smart key ECU assembly) communication input Engine switch off 11 to 14 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
F82-16 (IMI) - B29-1 (E1) Input G - W-B Certification ECU (smart key ECU assembly) communication output Engine switch off Below 1 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-

a.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F82-15 (IMO) - B29-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F82-16 (IMI) - B29-1 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected




CHECK ECM (for CVT)


A371911E14
0.625,0.5 1.125,0.75 0.5,0.25 1.979,0.5 2.479,0.75 0.5,0.25 3.375,0.5 3.875,0.75 0.5,0.25 4.74,0.5 5.24,0.75 0.5,0.25 5.979,0.5 6.479,0.75 0.5,0.25 0.75,0.542 1.208,0.74 0.458,0.198 10 false B46 2.115,0.542 2.573,0.74 0.458,0.198 10 false B47 3.5,0.542 3.958,0.74 0.458,0.198 10 false B48 4.833,0.542 5.292,0.74 0.458,0.198 10 false F130 6.073,0.542 6.531,0.74 0.458,0.198 10 false F131

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
B46-3 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F131-3 (BATT) - B46-3 (E1) Input G - W-B +B power supply Always 11 to 14 V -
F131-1 (+B) - B46-3 (E1) Input R - W-B +B power supply Engine switch on (IG) 11 to 14 V -
F131-2 (+B2) - B46-3 (E1) Input R - W-B +B power supply Engine switch on (IG) 11 to 14 V -
F130-9 (IMO) - B46-3 (E1) Output BR - W-B Certification ECU (smart key ECU assembly) communication input Engine switch off 11 to 14 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
F130-10 (IMI) - B46-3 (E1) Input G - W-B Certification ECU (smart key ECU assembly) communication output Engine switch off Below 1 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-

a.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F130-9 (IMO) - B46-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F130-10 (IMI) - B46-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected




CHECK ECM (for Manual Transaxle)


A301712E20
1.198,0.167 1.698,0.417 0.5,0.25 2.552,0.167 3.052,0.417 0.5,0.25 4.063,0.167 4.563,0.417 0.5,0.25 5.313,0.167 5.813,0.417 0.5,0.25 5.406,0.219 5.865,0.417 0.458,0.198 10 false F131 4.167,0.219 4.625,0.417 0.458,0.198 10 false F130 2.698,0.219 3.156,0.417 0.458,0.198 10 false B47 1.323,0.219 1.781,0.417 0.458,0.198 10 false B46

Terminal No. (Symbol) Input/Output Wiring Color Terminal Description Condition Specified Condition Related Data List Item/DTC
B46-3 (E1) - Body ground - W-B - Body ground Ground Always Below 1 Ω -
F131-3 (BATT) - B46-3 (E1) Input G - W-B +B power supply Always 11 to 14 V -
F131-1 (+B) - B46-3 (E1) Input R - W-B +B power supply Engine switch on (IG) 11 to 14 V -
F131-2 (+B2) - B46-3 (E1) Input R - W-B +B power supply Engine switch on (IG) 11 to 14 V -
F130-9 (IMO) - B46-3 (E1) Output BR - W-B Certification ECU (smart key ECU assembly) communication input Engine switch off 11 to 14 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 1)
-
F130-10 (IMI) - B46-3 (E1) Input G - W-B Certification ECU (smart key ECU assembly) communication output Engine switch off Below 1 V -
Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected Pulse generation
(See waveform 2)
-

a.

Using an oscilloscope, check the waveform.

HINT:

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.


i.

Waveform 1 (Reference)

B325134C03
0.917,1.271 1.375,1.469 0.458,0.198 10 GND 2.719,1.354 3.177,1.552 0.458,0.198 10 *a 2.906,1.354 3.365,1.552 0.458,0.198 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F130-9 (IMO) - B46-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected


ii.

Waveform 2 (Reference)

B333259C02
0.844,1.24 1.302,1.438 0.458,0.198 10 GND 3.115,1.323 3.344,1.531 0.229,0.208 10 *a 3.313,1.323 3.542,1.531 0.229,0.208 10 *b
*a Approximately 160 ms *b Approximately 270 ms


Measurement Condition
Item Content
Tester Connection F130-10 (IMI) - B46-3 (E1)
Tool Setting 2 V/DIV., 500 ms./DIV.
Condition Within 3 seconds of engine start or within 3 seconds of engine switch turned on (IG) after battery cable disconnected and reconnected