Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2016.10–2017.10
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090184 ANTI-LOCK BRAKE SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  TEST MODE PROCEDURE  


WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK


a.

Release the parking brake.

NOTICE:

Before releasing the parking brake, move the shift lever to P for safety (for Continuously Variable Transaxle) or use wheel chocks to secure the vehicle (for Manual Transaxle).


HINT:

When the parking brake is applied or the brake fluid level is low, the brake warning light comes on.



b.

When the ignition switch is turned to ON, check that the ABS warning and brake warning lights come on for approximately 3 seconds.

HINT:
·

If the skid control ECU (brake actuator assembly) stores any DTCs, the ABS warning and brake warning lights will come on.

·

If any of the indicators remain on or do not come on, proceed to troubleshooting for the light circuits listed below.



Trouble Area See Procedure
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)
Brake warning light circuit (Remains on) (Click here)
Brake warning light circuit (Does not come on) (Click here)



SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using GTS)


HINT:
·

If the ignition switch is turned from ON to ACC or off during Test Mode (signal check), DTCs recorded during the sensor check will be cleared.

·

During Test Mode (signal check), the skid control ECU (brake actuator assembly) records all DTCs detected in the sensor check. By performing Test Mode (signal check), the codes are cleared if a normal condition is confirmed. The remaining codes are the codes indicating where an abnormality was found.



a.

Procedure to enter Test Mode.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is in the straight-ahead position.


iii.

Apply the parking brake.


iv.

Check that the shift lever is in neutral (for Manual Transaxle).


v.

Check that the shift lever is in P (for Continuously Variable Transaxle).


vi.

Connect the GTS to the DLC3.


vii.

Turn the ignition switch to ON.


viii.

Turn the GTS on.


ix.

Switch the skid control ECU (brake actuator assembly) to Test Mode using the GTS.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3

x.

Check that the ABS warning light comes on for several seconds and then blinks in the Test Mode blinking pattern.

HINT:

If the ABS warning light does not blink, inspect the TS and CG terminal circuit and ABS warning light circuit.


Trouble Area See Procedure
TS and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)



b.

Speed Sensor Check

i.

Drive the vehicle straight-ahead.

Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.

·

The sensor check may not be completed if wheelspin occurs.

·

The ABS warning light blinks when the sensor check has been completed and the brake pedal is depressed.

·

The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor check.



ii.

Stop the vehicle.

NOTICE:
·

The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.

·

After the ABS warning light goes off and if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).

·

If the sensor check has not been completed, the ABS warning light blinks during driving and the ABS system does not operate.



HINT:

When the sensor check has been completed, the ABS warning light remains off during driving and blinks in the Test Mode pattern while the vehicle is stationary.




c.

End of Sensor Check

i.

If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.

NOTICE:

If the sensor check is not completed, the ABS warning light blinks even while the vehicle is being driven and the ABS does not operate.




d.

Reading Sensor Check DTCs

i.

Read the DTC(s) by following the GTS screen.

NOTICE:
·

If only the DTCs are displayed, repair the malfunction area and clear the DTCs.

·

If Test Mode sensor check DTCs and other DTCs are displayed or if only Test Mode sensor check DTCs are displayed, repair the malfunctions, clear the DTCs, and perform the Test Mode inspection again.





e.

List of DTCs.

ABS Sensor
DTC Code Detection Item Trouble Area
C1271 Low output signal of front speed sensor RH Front speed sensor and speed sensor rotor RH (Front axle hub sub-assembly RH)
C1272 Low output signal of front speed sensor LH Front speed sensor and speed sensor rotor LH (Front axle hub sub-assembly LH)
C1273 Low output signal of rear speed sensor RH
·

Rear speed sensor RH (Rear axle hub and bearing assembly RH)

·

Sensor installation

·

Speed sensor rotor (Rear axle hub and bearing assembly RH)


C1274 Low output signal of rear speed sensor LH
·

Rear speed sensor LH (Rear axle hub and bearing assembly LH)

·

Sensor installation

·

Speed sensor rotor (Rear axle hub and bearing assembly LH)


C1275 Abnormal change in output signal of front speed sensor RH Front speed sensor and speed sensor rotor RH (Front axle hub sub-assembly RH)
C1276 Abnormal change in output signal of front speed sensor LH Front speed sensor and speed sensor rotor LH (Front axle hub sub-assembly LH)
C1277 Abnormal change in output signal of rear speed sensor RH
·

Rear speed sensor RH (Rear axle hub and bearing assembly RH)

·

Rear speed sensor rotor (Rear axle hub and bearing assembly RH)


C1278 Abnormal change in output signal of rear speed sensor LH
·

Rear speed sensor LH (Rear axle hub and bearing assembly LH)

·

Rear speed sensor rotor (Rear axle hub and bearing assembly LH)



HINT:

The codes in this table are output only in Test Mode (signal check).



f.

Turn the ignition switch off and disconnect the GTS.



SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using SST Check Wire)


HINT:
·

If the ignition switch is turned from ON to ACC or off during Test Mode (signal check), DTCs recorded during the sensor check will be cleared.

·

During Test Mode (signal check), the skid control ECU (brake actuator assembly) records all DTCs detected in the sensor check. By performing Test Mode (signal check), the codes are cleared if a normal condition is confirmed. The remaining codes are the codes indicating where an abnormality was found.



a.

Procedure to enter Test Mode.

i.

Turn the ignition switch off.


ii.

Check that the steering wheel is in the straight-ahead position.


iii.

Apply the parking brake.


iv.

Check that the shift lever is in neutral (for Manual Transaxle).


v.

Check that the shift lever is in P (for Continuously Variable Transaxle).


vi.
C280109C35
1.625,0.813 1.969,0.385 true 1.583,1.5 1.24,1.885 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *1 1.99,0.302 2.302,0.5 0.313,0.198 10 false CG 1.021,1.813 1.292,2.01 0.271,0.198 10 false TS
*1 DLC3


Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

SST
09843-18040  


vii.

Turn the ignition switch to ON.


viii.

Check that the ABS warning light comes on for several seconds and then blink in Test Mode.

HINT:

If the ABS warning light does not blink, inspect the 12 (TS) and 4 (CG) terminal circuit and ABS warning light circuit.


Trouble Area See Procedure
TS and CG terminal circuit (Click here)
ABS warning light circuit (Remains on) (Click here)
ABS warning light circuit (Does not come on) (Click here)



b.

Speed Sensor Check

i.

Drive the vehicle straight-ahead.

Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds and check that the ABS warning light goes off.

·

The sensor check may not be completed if wheelspin occurs.

·

The ABS warning light blinks when the sensor check has been completed and the brake pedal is depressed.

·

The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor check.



ii.

Stop the vehicle.

NOTICE:
·

The speed sensor check may not be completed if the sensor check is started with the steering wheel turned or one or more wheels spinning.

·

After the ABS warning light goes off and if the vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).

·

If the sensor check has not been completed, the ABS warning light blinks during driving and the ABS system does not operate.



HINT:

When the sensor check has been completed, the ABS warning light remains on during driving and blinks in the Test Mode pattern while the vehicle is stationary.




c.

End of Sensor Check

i.

If the sensor check is completed, the ABS warning light blinks (Test Mode) when the vehicle stops and the ABS warning light is off while the vehicle is being driven.

NOTICE:

If the sensor check is not completed, the ABS warning light will blink even while the vehicle is driven and the ABS will not operate.




d.
C280109C36
1.865,1.49 2.188,1.896 true 1.604,1.479 1.281,1.885 true 1.99,0.385 1.667,0.792 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *1 2.031,0.292 2.344,0.49 0.313,0.198 10 false CG 1.063,1.823 1.313,2.031 0.25,0.208 10 false TS 2.25,1.823 2.5,2.031 0.25,0.208 10 false TC
*1 DLC3


Reading Sensor Check DTCs

i.

Using SST, connect terminals 12 (TS), 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  


ii.

Count the number of blinks of the ABS warning light.

NOTICE:
·

If only DTCs other than Test Mode sensor check DTCs are displayed, repair the malfunctions and clear the DTCs.

·

If Test Mode sensor check DTCs and other DTCs are displayed or if only Test Mode sensor check DTCs are displayed, repair the malfunctions, clear the DTCs, and perform the Test Mode inspection again.



HINT:
·

When the system is operating correctly, each light will blink continuously in a pattern of 0.25 seconds on, and then 0.25 seconds off.

·

When one DTC is output, each light will output the same code at 4 second intervals (for example, code 21 would be output as 2 flashes, a 1.5 second pause, and then 1 flash).

·

When 2 or more DTCs are output, each light will output a different code at 2.5 second intervals, and when all codes have been output, there will be a 4 second pause and the sequence will repeat.

·

When multiple codes are stored, they are output in order starting with the lowest DTC number.




iii.

After performing the check, disconnect SST from terminals TS and CG, and TC and CG of the DLC3 and turn the ignition switch off.


iv.

Turn the ignition switch to ON.

HINT:
·

If the ignition switch is not turned to ON after SST is removed from the DLC3, the previous Test Mode will continue.

·

If the ignition switch is turned to ON with terminals TS and CG shorted, the previous Test Mode will continue.





e.

Sensor Check DTCs

ABS Sensor:
DTC Code Detection Item Trouble Area
71 Low output signal of front speed sensor RH Front speed sensor and speed sensor rotor RH (Front axle hub sub-assembly RH)
72 Low output signal of front speed sensor LH Front speed sensor and speed sensor rotor LH (Front axle hub sub-assembly LH)
73 Low output signal of rear speed sensor RH
·

Rear speed sensor RH (Rear axle hub and bearing assembly RH)

·

Sensor installation

·

Speed sensor rotor (Rear axle hub and bearing assembly RH)


74 Low output signal of rear speed sensor LH
·

Rear speed sensor LH (Rear axle hub and bearing assembly LH)

·

Sensor installation

·

Speed sensor rotor (Rear axle hub and bearing assembly LH)


75 Abnormal change in output signal of front speed sensor RH Front speed sensor and speed sensor rotor RH (Front axle hub sub-assembly RH)
76 Abnormal change in output signal of front speed sensor LH Front speed sensor and speed sensor rotor LH (Front axle hub sub-assembly LH)
77 Abnormal change in output signal of rear speed sensor RH
·

Rear speed sensor RH (Rear axle hub and bearing assembly RH)

·

Rear speed sensor rotor (Rear axle hub and bearing assembly RH)


78 Abnormal change in output signal of rear speed sensor LH
·

Rear speed sensor LH (Rear axle hub and bearing assembly LH)

·

Rear speed sensor rotor (Rear axle hub and bearing assembly LH)




HINT:

The codes in this table are output only in Test Mode (signal check).