Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2016.10
RM30M0E _58 Vehicle Interior _017113 METER / GAUGE / DISPLAY _0087658 METER / GAUGE SYSTEM L

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  PRECAUTION  


IGNITION SWITCH EXPRESSIONS


a.

The type of ignition switch used on this model differs according to the specifications of the vehicle. The expressions listed in the table below are used in this section.

Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)



FUEL RECEIVER GAUGE OPERATION


a.

OPERATION

The combination meter assembly uses the fuel sender gauge assembly to detect the amount of fuel remaining in the fuel tank assembly. The fuel sender gauge assembly has a variable resistor whose resistance changes according to the amount of fuel remaining. The gauge assemblies receive voltage from the combination meter assembly and change the voltage based on the resistance that changes according to the amount of fuel remaining in the fuel tank assembly. The combination meter assembly detects the voltage between each variable resistor and each resistor in the combination meter assembly, and operates the fuel receiver gauge.


b.

FUEL RECEIVER GAUGE READING

i.

During normal driving:

As the fuel level in the fuel tank assembly rises and falls when driving on a hill or applying brakes, if the fuel sender gauge assembly output value were displayed as-is, the displayed value would fluctuate. For this reason, the averaged output value of the fuel sender gauge assembly is displayed.


ii.

During refueling:

The fuel level in the fuel tank assembly rises rapidly when fuel is added. If the averaging process that is used during normal driving is used in this case, the fuel receiver gauge reading cannot be updated promptly. Therefore, when it is judged that fuel is being added to the vehicle based on the shift lever position and changes in the fuel level, output values from the fuel sender gauge assembly are immediately reflected in the fuel receiver gauge reading. This control is called refueling judgment.



c.

REFUELING JUDGEMENT CONDITIONS

NOTICE:

Add fuel with the ignition switch off to ensure safety and to enable refueling judgment so that an appropriate fuel receiver gauge reading is obtained. If it is necessary to add fuel with the ignition switch ON, first move the shift lever to P or N*1, or apply the parking brake*2. Before driving the vehicle, wait until the fuel level indicated by the fuel receiver gauge stops rising (Approximately 1 minute from E to F).

*1: for CVT

*2: for Manual Transaxle



i.

Normal judgment condition (When normal refueling method is used)

With the ignition switch off, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.


ii.

Other judgment conditions (When other refueling method is used)

Any of the following conditions is met:

·

With the vehicle and engine stopped and the ignition switch ON, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level.

·

With the vehicle stopped, the engine running, the ignition switch ON and the shift lever in P or N, the fuel sender gauge assembly detects a change of 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more in the fuel level*1.

·

With the vehicle stopped, the engine running, the ignition switch ON and the shift lever in any driving position, the fuel sender gauge assembly detects a change of 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more in the fuel level*1.

·

The vehicle speed is 1.75 km/h (1.09 mph) or less (vehicle stopped) for 20 seconds or more continuously, and the fuel sender gauge assembly detects a change of 5 liters (5.3 US qts, 4.3 Imp. qts) or more in the fuel level*2.

*1: for CVT

*2: for Manual Transaxle





d.

PRECAUTION FOR REFUELING

i.

The fuel sender gauge assembly cannot detect changes in fuel level within certain ranges (around points E and F). Therefore, even though 5.0 liters (5.3 US qts, 4.4 Imp. qts) or more of fuel is added, refueling judgment may not be performed and the fuel receiver gauge reading may not change when fuel level is within such ranges.


ii.

It takes approximately 1 minute for the fuel sender gauge assembly to change from E to F. If the vehicle is driven while the displayed fuel level is still rising, the fuel sender gauge assembly will be stopped at that point. The system will then return to normal operation mode, and the displayed fuel level will rise at a rate of approximately 1 minute/L (0.946 minutes/US qt, 1.14 minutes/Imp. qt) when the vehicle is being driven, or approximately 6 minutes/L (5.68 minutes/US qt, 6.82 minutes/Imp. qt) when the vehicle is stopped.



e.

FORCED RESET OF FUEL RECEIVER GAUGE

When driving at 20 km/h (12 mph) or more, if the output values from the fuel sender gauge assembly are different from the fuel receiver gauge reading by 15.0 liters (15.9 US qts, 13.2 Imp. qts) or more for approximately 2 minutes, output values from fuel sender gauge assembly are immediately reflected in the fuel receiver gauge reading to compensate for a situation when refueling judgment cannot be made.