Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR › 2016.10–2017.10
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0090185 BRAKE ACTUATOR A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DRAIN BRAKE FLUID

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 44510 7.REMOVE BRAKE ACTUATOR ASSEMBLY (for LHD)

a.

for CVT w/ VSC:

i.
C349608C02
2.021,0.24 2.406,0.292 false 1.844,0.135 2.156,0.292 0.313,0.156 10 false *a
*a Lock Lever


Release the lock lever to disconnect the brake actuator connector.

NOTICE:

Be careful not to allow brake fluid to enter the removed connector.



ii.
C349610

Using a 10 mm and 12 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.


iii.
C349611C01
1.01,0.813 1.26,0.938 false 1.198,0.5 1.5,0.594 false 1.74,0.604 2.042,0.302 true 1.885,0.635 2.208,0.438 true 2.021,0.688 2.302,0.625 true 1.719,1.125 1.573,1.344 false 1.031,0.396 1.344,0.552 0.313,0.156 10 false *a 2.354,0.531 2.667,0.688 0.313,0.156 10 false *b 2.24,0.333 2.552,0.49 0.313,0.156 10 false *c 2.083,0.198 2.396,0.354 0.313,0.156 10 false *d 0.854,0.708 1.167,0.865 0.313,0.156 10 false *e 1.5,1.365 1.813,1.521 0.313,0.156 10 false *f
*a to Front Wheel Cylinder RH
*b to Front Wheel Cylinder LH
*c to Rear Wheel Cylinder RH
*d to Rear Wheel Cylinder LH
*e from Front Master Cylinder
*f from Rear Master Cylinder


Use tags or make a memo to identify the places to reconnect the brake tubes.


iv.
C349615

Remove the 3 bolts and brake actuator assembly with the brake actuator bracket assembly.

NOTICE:
·

Do not damage the brake tubes or wire harness.

·

Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.




v.
C349612

Remove the 3 bolts and No. 1 brake actuator bracket assembly.



b.

for CVT w/ ABS:

i.
C349608C02
2.021,0.24 2.406,0.292 false 1.844,0.135 2.156,0.292 0.313,0.156 10 false *a
*a Lock Lever


Release the lock lever to disconnect the brake actuator connector.

NOTICE:

Be careful not to allow brake fluid to enter the removed connector.



ii.
C349610

Using a 10 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.


iii.
C349611C01
1.01,0.813 1.26,0.938 false 1.198,0.5 1.5,0.594 false 1.74,0.604 2.042,0.302 true 1.885,0.635 2.208,0.438 true 2.021,0.688 2.302,0.625 true 1.719,1.125 1.573,1.344 false 1.031,0.396 1.344,0.552 0.313,0.156 10 false *a 2.354,0.531 2.667,0.688 0.313,0.156 10 false *b 2.24,0.333 2.552,0.49 0.313,0.156 10 false *c 2.083,0.198 2.396,0.354 0.313,0.156 10 false *d 0.854,0.708 1.167,0.865 0.313,0.156 10 false *e 1.5,1.365 1.813,1.521 0.313,0.156 10 false *f
*a to Front Wheel Cylinder RH
*b to Front Wheel Cylinder LH
*c to Rear Wheel Cylinder RH
*d to Rear Wheel Cylinder LH
*e from Front Master Cylinder
*f from Rear Master Cylinder


Use tags or make a memo to identify the places to reconnect the brake tubes.


iv.
C349615

Remove the 3 bolts and brake actuator assembly with the brake actuator bracket assembly.

NOTICE:
·

Do not damage the brake tubes or wire harness.

·

Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.




v.
C349612

Remove the 3 bolts and No. 1 brake actuator bracket assembly.



c.

except CVT w/ VSC:

i.
C285142C01
1.833,1.396 2.26,1.188 false 1.667,1.302 1.979,1.458 0.313,0.156 10 false *a
*a Lock Lever


Release the lock lever to disconnect the brake actuator connector.

NOTICE:

Be careful not to allow brake fluid to enter the removed connector.



ii.
C286075

Using a 10 mm and 12 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.


iii.
C286826C01
1.156,1.25 1.344,1.042 true 0.479,0.5 0.885,0.792 true 0.719,0.26 1.125,0.552 true 1.667,0.708 1.917,0.458 true 1.51,0.625 1.885,0.24 true 1.354,0.583 1.438,0.26 true 0.531,0.135 0.844,0.292 0.313,0.156 10 false *a 1.938,0.354 2.25,0.51 0.313,0.156 10 false *b 1.906,0.146 2.094,0.323 0.188,0.177 10 true *c 1.458,0.156 1.635,0.313 0.177,0.156 10 false *d 0.323,0.396 0.635,0.552 0.313,0.156 10 false *e 1.031,1.24 1.344,1.396 0.313,0.156 10 false *f
*a to Front Wheel Cylinder RH
*b to Front Wheel Cylinder LH
*c to Rear Wheel Cylinder RH
*d to Rear Wheel Cylinder LH
*e from Front Master Cylinder
*f from Rear Master Cylinder


Use tags or make a memo to identify the places to reconnect the brake tubes.


iv.
C286076

Remove the 3 bolts and brake actuator assembly with the brake actuator bracket assembly.

NOTICE:
·

Do not damage the brake tubes or wire harness.

·

Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.





d.

except CVT w/ ABS:

i.
C285142C01
1.833,1.396 2.26,1.188 false 1.667,1.302 1.979,1.458 0.313,0.156 10 false *a
*a Lock Lever


Release the lock lever to disconnect the brake actuator connector.

NOTICE:

Be careful not to allow brake fluid to enter the removed connector.



ii.
C286075

Using a 10 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.


iii.
C286826C01
1.156,1.25 1.344,1.042 true 0.479,0.5 0.885,0.792 true 0.719,0.26 1.125,0.552 true 1.667,0.708 1.917,0.458 true 1.51,0.625 1.885,0.24 true 1.354,0.583 1.438,0.26 true 0.531,0.135 0.844,0.292 0.313,0.156 10 false *a 1.938,0.354 2.25,0.51 0.313,0.156 10 false *b 1.906,0.146 2.094,0.323 0.188,0.177 10 true *c 1.458,0.156 1.635,0.313 0.177,0.156 10 false *d 0.323,0.396 0.635,0.552 0.313,0.156 10 false *e 1.031,1.24 1.344,1.396 0.313,0.156 10 false *f
*a to Front Wheel Cylinder RH
*b to Front Wheel Cylinder LH
*c to Rear Wheel Cylinder RH
*d to Rear Wheel Cylinder LH
*e from Front Master Cylinder
*f from Rear Master Cylinder


Use tags or make a memo to identify the places to reconnect the brake tubes.


iv.
C286076

Remove the 3 bolts and brake actuator assembly with the brake actuator bracket assembly.

NOTICE:
·

Do not damage the brake tubes or wire harness.

·

Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.





Hide 44510 8.REMOVE BRAKE ACTUATOR ASSEMBLY (for RHD)

a.
C285142C01
1.833,1.396 2.26,1.188 false 1.667,1.302 1.979,1.458 0.313,0.156 10 false *a
*a Lock Lever


Release the lock lever to disconnect the brake actuator connector.

NOTICE:

Be careful not to allow brake fluid to enter the removed connector.



b.
C232052

Using a 10 mm union nut wrench, disconnect the 6 brake tubes from the brake actuator assembly.


c.
C287089C01
1.229,1.271 1.396,1.042 true 0.948,0.792 0.583,0.49 true 1.708,0.719 2.01,0.458 true 1.563,0.646 1.844,0.24 true 1.177,0.563 0.844,0.188 true 1.427,0.594 1.615,0.177 true 0.677,0.073 0.99,0.229 0.313,0.156 10 false *a 2.031,0.354 2.344,0.51 0.313,0.156 10 false *b 1.875,0.125 2.188,0.281 0.313,0.156 10 false *c 1.656,0.073 1.833,0.229 0.177,0.156 10 true *d 0.427,0.365 0.74,0.521 0.313,0.156 10 false *e 1.094,1.198 1.26,1.385 0.167,0.188 10 false *f
*a to Front Wheel Cylinder RH
*b to Front Wheel Cylinder LH
*c to Rear Wheel Cylinder RH
*d to Rear Wheel Cylinder LH
*e from Rear Master Cylinder
*f from Front Master Cylinder


Use tags or make a memo to identify the places to reconnect the brake tubes.


d.
C169912

Remove the 3 bolts and brake actuator assembly with the brake actuator bracket assembly.

NOTICE:
·

Do not damage the brake tubes or wire harness.

·

Do not carry the brake actuator assembly with the brake actuator bracket assembly by the connector.




Hide 44590 9.REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY (for LHD)

a.

for CVT:

i.
C349619

Remove the 3 bolts and brake actuator bracket assembly from the brake actuator assembly.

NOTICE:

Do not carry the brake actuator assembly by the connector.




b.

except CVT:

i.
C286077

Remove the 3 bolts and brake actuator bracket assembly from the brake actuator assembly.

NOTICE:

Do not carry the brake actuator assembly by the connector.




Hide 44590 10.REMOVE BRAKE ACTUATOR BRACKET ASSEMBLY (for RHD)

a.
C169913

Remove the 3 bolts and brake actuator bracket assembly from the brake actuator assembly.

NOTICE:

Do not carry the brake actuator assembly by the connector.



Hide 44546A 11.REMOVE BRAKE ACTUATOR BRACKET CUSHION

a.

Remove the 3 brake actuator case collars from the 3 brake actuator bracket cushions.


b.

Remove the 3 brake actuator bracket cushions from the brake actuator bracket assembly.