41336E
1.INSTALL FRONT DRIVE SHAFT DUST COVER
| *a | Steel Plate |
Using SST, a steel plate and a press, install a new front drive shaft dust cover.
The front drive shaft dust cover should be completely installed.
Be careful not to damage the front drive shaft dust cover.
2.INSTALL FRONT AXLE OUTBOARD JOINT BOOT
| *a | Protective Tape |
Wrap the splines of the front drive outboard joint shaft assembly with protective tape to prevent the boot from being damaged.
| *1 | Front Drive Outboard Joint Shaft Assembly |
| *2 | Front No. 2 Axle Outboard Joint Boot Clamp |
| *3 | Front Axle Outboard Joint Boot |
| *4 | Front Axle Outboard Joint Boot Clamp |
|
Outboard joint side |
|
Inboard joint side |
Install new parts onto the front drive outboard joint shaft assembly in the following order:
Front No. 2 axle outboard joint boot clamp
Front axle outboard joint boot
Front axle outboard joint boot clamp
Pack the joint portion of the front drive outboard joint shaft assembly and front axle outboard joint boot with grease.
125 to 135 g (4.41 to 4.76 oz.)
Install the front axle outboard joint boot into the front drive outboard joint shaft assembly groove.
Do not allow grease to adhere to the boot clamp track of the front axle outboard joint boot.
Keep the inside of the front axle outboard joint boot free of foreign matter.
43447F
3.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP
Hold the front drive outboard joint shaft assembly in a vise between aluminum plates.
Do not overtighten the vise.
Install the front No. 2 axle outboard joint boot clamp onto the front axle outboard joint boot.
| *a | Hold |
| *b | Turn |
Place SST onto the front No. 2 axle outboard joint boot clamp, press it against the boot and slightly tighten SST.
Tighten SST so that the front No. 2 axle outboard joint boot clamp is pinched.
Do not overtighten SST.
Remove SST.
Using SST, measure the clearance of the front No. 2 axle outboard joint boot clamp.
2.1 mm (0.0827 in.) or less
If the clearance is outside the specified range, retighten SST.
43447E
4.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP
Install the front axle outboard joint boot clamp onto the front axle outboard joint boot.
| *a | Hold |
| *b | Turn |
Place SST onto the front axle outboard joint boot clamp, press it against the boot and slightly tighten SST.
Tighten SST so that the front axle outboard joint boot clamp is pinched.
Do not overtighten SST.
Remove SST.
Using SST, measure the clearance of the front axle outboard joint boot clamp.
1.3 mm (0.0512 in.) or less
If the clearance is outside the specified range, retighten SST.
43474E
5.INSTALL FRONT DRIVE SHAFT DAMPER LH
| *1 | Front Drive Outboard Joint Shaft Assembly |
| *2 | Front Drive Shaft Damper LH |
| *3 | Front Drive Shaft Damper Clamp |
Install parts to the front drive outboard joint shaft assembly in the following order as shown in the illustration.
New front drive shaft damper clamp
Front drive shaft damper LH
New front drive shaft damper clamp
Set the dimension (A) as specified below.
262.9 to 266.9 mm (10.4 to 10.5 in.)
Hold the drive shaft in a vise between aluminum plates.
Do not overtighten the vise.
Install the 2 front drive shaft damper clamps to the front drive shaft damper LH.
Be sure to install the clamp in the correct position.
Using needle-nose pliers, engage the 2 claws to install the 2 front drive shaft damper clamps as shown in the illustration.
43474D
6.INSTALL FRONT DRIVE SHAFT DAMPER RH
for CVT with 1NR-FE:
| *1 | Front Drive Outboard Joint Shaft Assembly |
| *2 | Front Drive Shaft Damper RH |
| *3 | Front Drive Shaft Damper Clamp |
Install parts to the front drive outboard joint shaft assembly in the following order as shown in the illustration.
New front drive shaft damper clamp
Front drive shaft damper RH
New front drive shaft damper clamp
Set the dimension (A) as specified below.
490.3 to 494.3 mm (1.61 to 1.62 ft.)
Hold the drive shaft in a vise between aluminum plates.
Do not overtighten the vise.
Install the 2 front drive shaft damper clamps to the front drive shaft damper RH.
Be sure to install the clamp in the correct position.
Using needle-nose pliers, engage the 2 claws to install the 2 front drive shaft damper clamps as shown in the illustration.
for CVT with 2NR-FE:
| *1 | Front Drive Outboard Joint Shaft Assembly |
| *2 | Front Drive Shaft Damper RH |
| *3 | Front Drive Shaft Damper Clamp |
Install parts to the front drive outboard joint shaft assembly in the following order as shown in the illustration.
New front drive shaft damper clamp
Front drive shaft damper RH
New front drive shaft damper clamp
Set the dimension (A) as specified below.
459.3 to 463.3 mm (1.506 to 1.519 ft.)
Hold the drive shaft in a vise between aluminum plates.
Do not overtighten the vise.
Install the 2 front drive shaft damper clamps to the front drive shaft damper RH.
Be sure to install the clamp in the correct position.
| *a | Hold |
| *b | Turn |
Place SST onto the front drive shaft damper clamp, press it against the front drive shaft damper RH and slightly tighten SST.
Use the same procedure for both sides.
Tighten SST so that the front drive shaft damper clamp is pinched.
Do not overtighten SST.
Use the same procedure for both sides.
Remove SST.
Using SST, measure the clearance of the 2 front drive shaft damper clamps.
1.3 mm (0.0512 in.) or less
If the clearance is outside the specified range, retighten SST.
for Manual Transaxle:
| *1 | Front Drive Outboard Joint Shaft Assembly |
| *2 | Front Drive Shaft Damper RH |
| *3 | Front Drive Shaft Damper Clamp |
Install parts to the front drive outboard joint shaft assembly in the following order as shown in the illustration.
New front drive shaft damper clamp
Front drive shaft damper RH
New front drive shaft damper clamp
Set the dimension (A) as specified below.
459.3 to 463.3 mm (1.506 to 1.519 ft.)
Hold the drive shaft in a vise between aluminum plates.
Do not overtighten the vise.
Install the 2 front drive shaft damper clamps to the front drive shaft damper RH.
Be sure to install the clamp in the correct position.
| *a | Hold |
| *b | Turn |
Place SST onto the front drive shaft damper clamp, press it against the front drive shaft damper RH and slightly tighten SST.
Use the same procedure for both sides.
Tighten SST so that the front drive shaft damper clamp is pinched.
Do not overtighten SST.
Use the same procedure for both sides.
Remove SST.
Using SST, measure the clearance of the 2 front drive shaft damper clamps.
1.3 mm (0.0512 in.) or less
If the clearance is outside the specified range, retighten SST.
7.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY
| *1 | Front Axle Inboard Joint Boot Clamp |
| *2 | Front Axle Inboard Joint Boot |
| *3 | Front No. 2 Axle Inboard Joint Boot Clamp |
| *a | Protective Tape |
|
Outboard joint side |
|
Inboard joint side |
Install new parts onto the front drive outboard joint shaft assembly in the following order:
Front axle inboard joint boot clamp
Front axle inboard joint boot
Front No. 2 axle inboard joint boot clamp
Hold the front drive outboard joint shaft assembly in a vise between aluminum plates.
Do not overtighten the vise.
Remove the protective tape.
| *a | Matchmark |
Align the matchmarks and install the tripod joint onto the front drive outboard joint shaft assembly.
Face the serrated side of the tripod joint outward and install it onto the front drive outboard joint shaft assembly end.
Using a brass bar and a hammer, install the tripod joint to the front drive outboard joint shaft assembly.
Do not tap the rollers.
Keep the tripod joint free of foreign matter.
Using a snap ring expander, install a new shaft snap ring to the front drive outboard joint shaft assembly.
Pack the front drive inboard joint assembly and front axle inboard joint boot with grease.
134 to 144 g (4.73 to 5.07 oz.)
| *a | Matchmark |
Align the matchmarks and install the front drive inboard joint assembly to the front drive outboard joint shaft assembly.
8.INSTALL FRONT AXLE INBOARD JOINT BOOT
Install the front axle inboard joint boot to the front drive inboard joint assembly.
Check whether each drive shaft dimension (A) is within specification.
| LH Side | 583.6 to 587.6 mm (1.91 to 1.92 ft.) |
| RH Side | 825.6 to 829.6 mm (2.71 to 2.72 ft.) |
43448F
9.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP
Hold the front drive outboard joint shaft assembly in a vise between aluminum plates.
Do not overtighten the vise.
Install the front axle inboard joint boot clamp onto the front axle inboard joint boot.
| *a | Hold |
| *b | Turn |
Place SST onto the front axle inboard joint boot clamp, press it against the boot and slightly tighten SST.
Tighten SST so that the front axle inboard joint boot clamp is pinched.
Do not overtighten SST.
Remove SST.
Using SST, measure the clearance of the front axle inboard joint boot clamp.
1.3 mm (0.0512 in.) or less
If the clearance is outside the specified range, retighten SST.
43448G
10.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP
Install the front No. 2 axle inboard joint boot clamp onto the front axle inboard joint boot.
| *a | Hold |
| *b | Turn |
Place SST onto the front No. 2 axle inboard joint boot clamp, press it against the boot and slightly tighten SST.
Tighten SST so that the front No. 2 axle inboard joint boot clamp is pinched.
Do not overtighten SST.
Remove SST.
Using SST, measure the clearance of the front No. 2 axle inboard joint boot clamp.
2.1 mm (0.0827 in.) or less
If the clearance is outside the specified range, retighten SST.
11.INSPECT FRONT DRIVE SHAFT ASSEMBLY