Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › NAME PLATE(for Sedan) › 2016.10–2017.10
RM30M0E _59 Vehicle Exterior _017128 EXTERIOR PANELS / TRIM _0092436 NAME PLATE(for Sedan) A

EXTERIOR PANELS / TRIM  NAME PLATE(for Sedan)  INSTALLATION  


PROCEDURE

Hide 75444 1.INSTALL NO. 4 LUGGAGE COMPARTMENT DOOR PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot vehicle body or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the No. 4 luggage compartment door plate while any double-sided tape remains on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

for 2NR-FE:

i.

Install a new No. 4 luggage compartment door plate as shown in the illustration.

B205198C01
5.729,2.635 5.99,2.635 false 5.719,0.813 5.875,1.01 0.156,0.198 10 false A 4.594,2.146 4.75,2.344 0.156,0.198 10 false B 5.646,1.906 5.802,2.104 0.156,0.198 10 false C 6.49,1.99 6.646,2.188 0.156,0.198 10 false D 6.031,2.542 6.344,2.74 0.313,0.198 10 false *1
*1 Luggage Compartment Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 58.3 mm (2.30 in.) B 100.4 mm (3.95 in.)
C 58.6 mm (2.31 in.) D 121.8 mm (4.80 in.)


NOTICE:

Install the No. 4 luggage compartment door plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 4 luggage compartment door plate to 20 to 30°C (68 to 86°F) and install the No. 4 luggage compartment door plate.




c.

for 1NR-FE:

i.

Install a new No. 4 luggage compartment door plate as shown in the illustration.

B205199C01
5.917,2.5 6.167,2.5 false 6.208,2.406 6.521,2.604 0.313,0.198 10 false *1 5.75,0.792 6.063,0.99 0.313,0.198 10 false A 4.563,2.198 4.875,2.396 0.313,0.198 10 false B 5.656,1.885 5.969,2.083 0.313,0.198 10 false C 6.604,2.021 6.917,2.219 0.313,0.198 10 false D
*1 Luggage Compartment Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 73.7 mm (2.90 in.) B 103.7 mm (4.08 in.)
C 74.0 mm (2.91 in.) D 126.4 mm (4.98 in.)


NOTICE:

Install the No. 4 luggage compartment door plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 4 luggage compartment door plate to 20 to 30°C (68 to 86°F) and install the No. 4 luggage compartment door plate.




Hide 75443A 2.INSTALL NO. 3 LUGGAGE COMPARTMENT DOOR PLATE (for 2NR-FE)

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot vehicle body or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the No. 3 luggage compartment door plate while any double-sided tape remains on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 3 luggage compartment door plate as shown in the illustration.

B205200C01
5.948,2.458 6.208,2.458 false 5.771,0.865 5.927,1.063 0.156,0.198 10 false A 4.094,2.208 4.25,2.406 0.156,0.198 10 false B 5.25,1.885 5.406,2.083 0.156,0.198 10 false C 6.615,2.021 6.771,2.219 0.156,0.198 10 false D 6.229,2.385 6.542,2.583 0.313,0.198 10 false *1
*1 Luggage Compartment Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 66.0 mm (2.598 in.) B 110.1 mm (4.33 in.)
C 114.4 mm (4.504 in.) D 122.7 mm (4.83 in.)


NOTICE:

Install the No. 3 luggage compartment door plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 3 luggage compartment door plate to 20 to 30°C (68 to 86°F) and install the No. 3 luggage compartment door plate.



Hide 75442 3.INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot vehicle body or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the No. 2 luggage compartment door name plate while any double-sided tape remains on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 2 luggage compartment door name plate as shown in the illustration.

B205196C01
6.604,2.354 6.531,1.896 true 6.333,0.979 6.49,1.177 0.156,0.198 10 false A 3.698,1.969 3.854,2.167 0.156,0.198 10 false B 5.146,2.677 5.302,2.875 0.156,0.198 10 false C 6.833,1.802 6.99,2 0.156,0.198 10 false D 6.552,2.396 6.865,2.594 0.313,0.198 10 false *1
*1 Luggage Compartment Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 7.9 mm (0.311 in.) B 4.1 mm (0.161 in.)
C 145.3 mm (5.72 in.) D 26.1 mm (1.03 in.)


NOTICE:

Install the No. 2 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 2 luggage compartment door name plate to 20 to 30°C (68 to 86°F) and install the No. 2 luggage compartment door name plate.



Hide 75441A 4.INSTALL NO. 1 LUGGAGE COMPARTMENT DOOR NAME PLATE

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot vehicle body or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the No. 1 luggage compartment door name plate while any double-sided tape remains on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.

Install a new No. 1 luggage compartment door name plate as shown in the illustration.

B205197C01
4.208,1.615 4.625,1.198 false 4.635,1.063 4.948,1.26 0.313,0.198 10 false *1 3.875,1.802 4.031,2 0.156,0.198 10 false A 4.469,2.365 4.625,2.563 0.156,0.198 10 false B 5.177,2.833 5.333,3.031 0.156,0.198 10 false C 6.531,1.802 6.688,2 0.156,0.198 10 false D
*1 Luggage Compartment Door - -


Installation Position:
Mark Measurement (along surface) Mark Measurement (along surface)
A 4.7 mm (0.185 in.) B 16.8 mm (0.661 in.)
C 121.1 mm (4.77 in.) D 4.0 mm (0.157 in.)


NOTICE:

Install the No. 1 luggage compartment door name plate in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the No. 1 luggage compartment door name plate to 20 to 30°C (68 to 86°F) and install the No. 1 luggage compartment door name plate.



Hide 75431 5.INSTALL LUGGAGE COMPARTMENT DOOR EMBLEM

a.

Clean the attachment surface.

i.

Using an infrared light, heat the double-sided tape remaining on the vehicle body.

Heating Temperature
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)

CAUTION:

Do not burn yourself on the hot vehicle body or with the infrared light.


NOTICE:

Do not heat the vehicle body excessively.



ii.

Using a piece of cloth, rub the remaining double-sided tape off the vehicle body while it is hot from the infrared light.

NOTICE:

Installing the luggage compartment door emblem with any double-sided tape remaining on the vehicle body may cause adhesion failure. Therefore, completely remove the double-sided tape.



iii.

Using a non-residue solvent, clean the attachment surface.



b.
B342306C01
0.75,3.552 0.333,3.552 true 2.583,3.792 2.917,3.792 true 0.188,3.448 0.5,3.604 0.313,0.156 10 false *a 2.948,3.698 3.26,3.854 0.313,0.156 10 false *a
*a Location Pin


Insert the 2 location pins into the vehicle body and install a new luggage compartment door emblem.

NOTICE:

Install the luggage compartment door emblem in an environment where the ambient temperature is over 20°C (68°F). If it is below 20°C (68°F), using an infrared light, heat the vehicle body and the luggage compartment door emblem to 20 to 30°C (68 to 86°F) and install the luggage compartment door emblem.