Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › from 2017.10
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM C

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  P1585  Acceleration Sensor Circuit  


DESCRIPTION

The ECM determines the vehicle inclination based on a signal from the airbag ECU assembly (yaw rate and acceleration sensor). If a malfunction in the airbag ECU assembly (yaw rate and acceleration sensor) is determined based on a malfunction signal from the brake actuator assembly (skid control ECU), the ECM stores this DTC.

HINT:
·

The airbag ECU assembly (yaw rate and acceleration sensor) signal is sent to the brake actuator assembly (skid control ECU) via CAN communication.

·

If CAN communication DTCs are output, perform troubleshooting for those DTCs first.



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P1585 Acceleration Sensor Circuit After the ignition switch is turned ON, the brake actuator assembly (skid control ECU) has detected one of the following conditions, and the ECM has received a diagnostic signal from the brake actuator assembly (skid control ECU) for 3 seconds or more (1 trip detection logic).
·

Output value of the airbag sensor assembly (yaw rate and acceleration sensor) remains below -1.5 G or more than 1.5 G for at least 1.2 seconds or more.

·

Airbag sensor assembly (yaw rate and acceleration sensor) power source voltage is 4.4 V or less, or 5.6 V or higher, for at least 1.2 seconds or more.

·

No signal is detected from the airbag sensor assembly (yaw rate and acceleration sensor) 7 times or more.

·

Vehicle is stationary, and the difference between GL1 and GL2 does not decrease below 0.4 G within 60 seconds after it has exceeded 0.6 G.

·

Malfunction signal of the airbag sensor assembly (yaw rate and acceleration sensor) power source voltage has occurred for 10 seconds or more while the vehicle is driven at 3 km/h (1.8 mph) or more.


·

Airbag ECU assembly (Yaw rate and acceleration sensor)

·

CAN communication system

·

Brake actuator assembly (Skid control ECU)


Does not come on DTC stored

WIRING DIAGRAM

C390179E03
0.781,2.302 4.906,2.5 4.125,0.198 10 false to CAN Communication System 0.552,3.427 4.219,3.625 3.667,0.198 10 false : CAN Communication Line 4.333,2.938 6.531,3.354 2.198,0.417 10 false Airbag ECU Assembly (Yaw Rate and Acceleration Sensor) 4.344,2.75 4.802,2.948 0.458,0.198 10 false F21 4.927,2.052 5.542,2.25 0.615,0.198 10 false CANH 4.938,0.49 5.552,0.688 0.615,0.198 10 false CANH 1.781,0.51 2.396,0.708 0.615,0.198 10 false CANH 4.948,2.5 5.563,2.698 0.615,0.198 10 false CANL 4.948,0.958 5.563,1.156 0.615,0.198 10 false CANL 1.792,0.927 2.406,1.125 0.615,0.198 10 false CANL 0.99,1.542 2.583,2.01 1.594,0.469 10 false Brake Actuator Assembly (Skid Control ECU) 1,1.333 2,1.583 1,0.25 10 false A48*1, A49*2 4.844,1.333 5.458,1.531 0.615,0.198 10 false F130 4.844,1.5 5.302,1.698 0.458,0.198 10 false ECM 4.688,0.333 5,0.531 0.313,0.198 10 false 13 4.677,0.781 4.99,0.979 0.313,0.198 10 false 14 2.281,0.313 2.594,0.51 0.313,0.198 10 false 25 2.281,0.75 2.594,0.948 0.313,0.198 10 false 14 4.646,1.875 4.958,2.073 0.313,0.198 10 false 13 4.656,2.302 4.969,2.5 0.313,0.198 10 false 22 0.156,0.156 1.448,0.396 1.292,0.24 12 false w/ VSC: 0.167,2.667 1.177,2.917 1.01,0.25 10 false *1: for RHD 0.167,2.917 1.854,3.115 1.688,0.198 10 false *2: for LHD

C390179E06
0.781,2.281 4.906,2.479 4.125,0.198 10 false to CAN Communication System 0.552,3.427 4.219,3.625 3.667,0.198 10 false : CAN Communication Line 4.333,2.938 6.531,3.354 2.198,0.417 10 false Airbag ECU Assembly (Yaw Rate and Acceleration Sensor) 4.344,2.75 4.802,2.948 0.458,0.198 10 false F21 4.927,2.052 5.542,2.25 0.615,0.198 10 false CANH 4.938,0.49 5.552,0.688 0.615,0.198 10 false CANH 1.781,0.51 2.396,0.708 0.615,0.198 10 false CANH 4.948,2.5 5.563,2.698 0.615,0.198 10 false CANL 4.948,0.958 5.563,1.156 0.615,0.198 10 false CANL 1.792,0.927 2.406,1.125 0.615,0.198 10 false CANL 0.979,1.542 2.573,2.01 1.594,0.469 10 false Brake Actuator Assembly (Skid Control ECU) 0.99,1.344 1.979,1.604 0.99,0.26 10 false A35*1, A47*2 4.844,1.333 5.458,1.531 0.615,0.198 10 false F130 4.844,1.5 5.302,1.698 0.458,0.198 10 false ECM 4.688,0.333 5,0.531 0.313,0.198 10 false 13 4.677,0.781 4.99,0.979 0.313,0.198 10 false 14 2.281,0.313 2.594,0.51 0.313,0.198 10 false 25 2.281,0.75 2.594,0.948 0.313,0.198 10 false 14 4.646,1.875 4.958,2.073 0.313,0.198 10 false 13 4.656,2.302 4.969,2.5 0.313,0.198 10 false 22 0.177,0.167 1.646,0.406 1.469,0.24 12 false w/o VSC: 0.167,2.594 1.854,2.792 1.688,0.198 10 false *1: for RHD 0.177,2.927 1.865,3.125 1.688,0.198 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION


·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check for DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234

Result:
Result Proceed to
DTC U0129 is not output A
DTC U0129 is output B



A

2.READ VALUE USING GTS (G SENSOR)

B

2.READ VALUE USING GTS (G SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
G Sensor Converted output voltage of G sensor Min.: 0 V
Max.: 79.998 V
·

2.31 to 2.69 V: Vehicle on level ground

·

1.88 to 2.5 V: Decelerating

·

2.5 to 3.11 V: Accelerating

·

Stuck at 1.87 V: G sensor malfunction

·

Stuck at 1.87 V: Communication malfunction


-
Powertrain > Engine and ECT > Data List
Tester Display
G Sensor
50003 234 410

Result:
Result Proceed to
Data List value is not normal A
Data List value is normal B



A

3.REPLACE AIRBAG ECU ASSEMBLY

B

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

3.REPLACE AIRBAG ECU ASSEMBLY
a.

Replace the airbag ECU assembly (yaw rate and acceleration sensor).

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>COMPONENTS


Result:
Proceed to
NEXT



NEXT