Home › Drivetrain › K312 CVT › CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM › 2017.10–2018.01
RM30M0E _52 Drivetrain _052969 K312 CVT _0256556 CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM J

K312 CVT  CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM  Transmission Control Switch Circuit  


DESCRIPTION

After moving the shift lever to M, it is possible to change the shift range between M1 and M7 using the shift lever. Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" lowers the shift range by one.

WIRING DIAGRAM

C342245E26
1.76,0.469 1.917,0.667 0.156,0.198 10 false 4 2,0.469 2.313,0.667 0.313,0.198 10 false IG 3.177,0.469 3.333,0.667 0.156,0.198 10 false S 3.427,0.469 3.583,0.667 0.156,0.198 10 false 5 3.427,1.135 4.167,1.333 0.74,0.198 10 false 3*1, 1*2 3.427,1.833 4.25,2 0.823,0.167 10 false 1*1, 3*2 2.958,1.833 3.5,2.052 0.542,0.219 10 false SFTD 2.958,1.177 3.573,1.375 0.615,0.198 10 false SFTU 2.01,1.823 2.167,2.021 0.156,0.198 10 false E 1.76,1.833 1.917,2.031 0.156,0.198 10 false 2 4.938,0.469 5.25,0.667 0.313,0.198 10 false 30 4.938,1.167 5.25,1.365 0.313,0.198 10 false 17 4.938,1.865 5.25,2.063 0.313,0.198 10 false 27 5.219,1.885 5.833,2.083 0.615,0.198 10 false SFTD 5.219,1.167 5.833,1.365 0.615,0.198 10 false SFTU 5.25,0.49 5.406,0.688 0.156,0.198 10 false S 6.167,0.969 6.781,1.167 0.615,0.198 10 false 12 V 6.167,1.667 6.781,1.865 0.615,0.198 10 false 12 V 5.708,2.5 6.167,2.698 0.458,0.198 10 false B48 5.708,2.667 6.167,2.865 0.458,0.198 10 false ECM 1.583,2.417 2.042,2.615 0.458,0.198 10 false F133 1.583,2.615 3.615,3.417 2.031,0.802 10 false Shift Lock Control Unit Assembly (Transmission Control Switch) 0.281,0.625 1.135,1.938 0.854,1.313 10 false from ECU-IG NO. 1 Fuse*3 or ECU-IG NO. 3 Fuse*4 0.333,3 2.021,3.198 1.688,0.198 10 false *1: for LHD 0.333,3.333 2.021,3.531 1.688,0.198 10 false *2: for RHD 4.333,3.01 6.781,3.208 2.448,0.198 10 false *3: for TMT Made 4.333,3.333 6.031,3.563 1.698,0.229 10 false *4: for TMMIN Made

CAUTION / NOTICE / HINT

NOTICE:
·

Perform initialization after replacing any parts related to the continuously variable transaxle system.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION

·

Check that no DTCs are stored after performing initialization.

Click hereDrivetrain>K312 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes
50001 234

e.

Read the DTCs using the GTS.


Result:
Result Proceed to
DTCs are not output A
DTCs are output B



A

2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)

B

2.READ VALUE USING GTS (SPORTS MODE SELECTION SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List
Tester Display
Sports Mode Selection SW
50003 234 133

e.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Mode Selection SW Transmission control switch status OFF or ON
·

ON: Shift lever in M, "+" or "-"

·

OFF: Shift lever not in M, "+" or "-"


-

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

3.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)

B

7.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
3.READ VALUE USING GTS (SPORTS SHIFT UP SW AND SPORTS SHIFT DOWN SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List.


e.

According to the display on the GTS, read the Data List.

Powertrain > Engine and ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Sports Shift Up SW Sport shift up switch status OFF or ON
·

ON: Shift lever held in "+"

·

OFF: Shift lever not held in "+"


-
Sports Shift Down SW Sport shift down switch status OFF or ON
·

ON: Shift lever held in "-"

·

OFF: Shift lever not held in "-"


-
Powertrain > Engine and ECT > Data List
Tester Display
Sports Shift Up SW
Sports Shift Down SW
50003 234 134,135

Result:
Result Proceed to
Data List value is normal A
Data List value is not normal B



A

B

4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
4.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C239095C73
1.292,1.729 1.646,1.313 true 2.698,1.729 2.313,1.302 true 1.979,1.729 1.958,1.333 true 0.198,0.167 0.51,0.365 0.313,0.198 10 false *a 1.969,1.781 2.125,1.979 0.156,0.198 10 false E 1.042,1.76 1.958,1.958 0.917,0.198 10 false SFTU*A 1.042,1.969 1.958,2.167 0.917,0.198 10 false SFTD*B 2.427,1.792 3.344,1.99 0.917,0.198 10 false SFTD*A 2.427,1.99 3.333,2.177 0.906,0.188 10 false SFTU*B
*A for LHD
*B for RHD
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the F133 shift lock control unit assembly (transmission control switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Switch Condition Specified Condition
3 (SFTU) - 2 (E) Shift lever held in "+" Below 1 Ω
Shift lever in M 10 kΩ or higher
1 (SFTD) - 2 (E) Shift lever held in "-" Below 1 Ω
Shift lever in M 10 kΩ or higher


for RHD
Tester Connection Switch Condition Specified Condition
1 (SFTU) - 2 (E) Shift lever held in "+" Below 1 Ω
Shift lever in M 10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever held in "-" Below 1 Ω
Shift lever in M 10 kΩ or higher


c.

Connect the F133 shift lock control unit assembly (transmission control switch) connector.


Result:
Result Proceed to
OK A
NG (for TMT Made) B
NG (for TMMIN Made) C



A

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

B

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

C

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

5.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)
a.

Disconnect the B48 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
B48-27 (SFTD) - Body ground Shift lever held in "-" Below 1 Ω
Shift lever in M 10 kΩ or higher
B48-17 (SFTU) - Body ground Shift lever held in "+" Below 1 Ω
Shift lever in M 10 kΩ or higher



c.

Connect the B48 ECM connector.


Result:
Proceed to
OK
NG



OK

6.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)

6.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

7.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)
a.
C239095C12
0.771,1.729 1.125,1.313 true 1.906,1.75 1.521,1.323 true 0.198,0.167 0.51,0.365 0.313,0.198 10 *a 1.906,1.802 2.375,2 0.469,0.198 10 IG 0.646,1.771 1.021,1.979 0.375,0.208 10 S
*a Component without harness connected
(Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the F133 shift lock control unit assembly (transmission control switch) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
4 (IG) - 5 (S) Shift lever in M Below 1 Ω
Shift lever not in M 10 kΩ or higher



c.

Connect the F133 shift lock control unit assembly (transmission control switch) connector.


Result:
Result Proceed to
OK A
NG (for TMT Made) B
NG (for TMMIN Made) C



A

8.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) POWER SOURCE)

B

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

C

REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH)

8.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) POWER SOURCE)
a.
C267936C42
0.156,0.99 0.667,1.25 0.51,0.26 2.646,1.875 2,1.406 true 2.719,1.802 3.031,2 0.313,0.198 10 false IG 0.271,1.042 0.635,1.24 0.365,0.198 10 false F133 0.104,0.104 0.417,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Shift Lock Control Unit Assembly (Transmission Control Switch))


Disconnect the F133 shift lock control unit assembly (transmission control switch) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F133-4 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) - ECM)

NG

CHECK POWER SOURCE CIRCUIT (TRANSMISSION CONTROL SWITCH)

9.CHECK HARNESS AND CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) - ECM)
a.

Disconnect the B48 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F133-5 (S) - B48-30 (S) Always Below 1 Ω
F133-5 (S) - Body ground and other terminals Always 10 kΩ or higher
B48-30 (S) - Body ground and other terminals Always 10 kΩ or higher



c.

Connect the B48 ECM connector.


d.

Connect the F133 shift lock control unit assembly (transmission control switch) connector.


Result:
Proceed to
OK
NG



OK

10.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (SHIFT LOCK CONTROL UNIT ASSEMBLY (TRANSMISSION CONTROL SWITCH) - ECM)

10.REPLACE ECM

Result:
Proceed to
NEXT



NEXT