Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING(for Hatchback) › from 2017.10
RM30M0E _58 Vehicle Interior _017120 INTERIOR PANELS / TRIM _0116072 ROOF HEADLINING(for Hatchback) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for Hatchback)  INSTALLATION  


PROCEDURE

Hide 63310 1.INSTALL ROOF HEADLINING ASSEMBLY

a.
B484804C01
0,0 0,0 false
V113147

Install in this Direction


Put the roof headlining assembly into the vehicle through the back door.

NOTICE:

Do not damage the roof headlining assembly or body interior.



b.

Install the roof headlining assembly with the 2 clips.


c.

for Rear Pillar RH Side:

i.
B484791

Engage the hook to connect the No. 2 antenna cord sub-assembly.


ii.

Install the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


iii.

Connect the connector.


iv.

Engage the clamp.



Hide 2.INSTALL VISOR HOLDER LH

a.

Engage the 2 claws.


b.
B487753

Push in the visor holder LH as shown in the illustration.


Hide 3.INSTALL VISOR HOLDER RH

HINT:

Use the same procedure as for the LH side.


Hide 74320 4.INSTALL VISOR ASSEMBLY LH

a.

Install the visor assembly LH with the 2 screws.


b.

Engage the guide.


Hide 74310 5.INSTALL VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74610A 6.INSTALL ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure to install all assist grip sub-assemblies.


a.
B279001

Install the 2 clips and 2 assist grip covers to the assist grip as shown in the illustration.


b.

Engage the 2 clips to install the assist grip sub-assembly.


Hide 81240J 7.INSTALL ROOM LIGHT ASSEMBLY

Hide 81260A 8.INSTALL MAP LIGHT ASSEMBLY

Hide 62472A 9.INSTALL ROOF SIDE INNER GARNISH LH

a.

Pass the slip anchor of the rear center seat 3 point type belt assembly through the roof side inner garnish LH.


b.
B485546C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide (rear seatback rod knob LH).


c.

Engage the 6 clips to install the roof side inner garnish LH as shown in the illustration.


Hide 62471A 10.INSTALL ROOF SIDE INNER GARNISH RH

a.
B485545C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guide (rear seatback rod knob RH).


b.

Engage the 6 clips to install the roof side inner garnish RH as shown in the illustration.


Hide 73310D 11.CONNECT REAR CENTER SEAT 3 POINT TYPE BELT ASSEMBLY

a.
B485544C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws and 2 guides to connect the belt guide of the rear center seat 3 point type belt assembly as shown in the illustration.


b.

Connect the slip anchor of the rear center seat 3 point type belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
B485543

Engage the 2 claws to close the guide cover of the rear center seat 3 point type belt assembly.


Hide 62572A 12.INSTALL ROOF SIDE INNER LOWER GARNISH LH

a.
B487754C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 5 claws and 2 clips to install the roof side inner lower garnish LH as shown in the illustration.


b.

Install the screw.


Hide 62571A 13.INSTALL ROOF SIDE INNER LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 81330 14.INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY

Hide 62552F 15.INSTALL REAR SEAT SIDE GARNISH LH

a.
B487755C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws, clip and guide to install the rear seat side garnish LH as shown in the illustration.


Hide 62551F 16.INSTALL REAR SEAT SIDE GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73370 17.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH

a.

Engage the clamp to connect the rear seat 3 point type outer belt assembly LH.


b.

Install the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73360 18.CONNECT REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 64740C 19.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH

a.

Install the deck trim side panel assembly RH with the 7 clips.


Hide 64730B 20.INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 64716D 21.INSTALL REAR DECK TRIM COVER

a.
B485540C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 4 claws and 2 guides to install the rear deck trim cover as shown in the illustration.


b.

Install the 2 clips.


Hide 62412B 22.INSTALL CENTER PILLAR UPPER GARNISH LH

a.
B487756C01
0,0 0,0 false
V113147

Install in this Direction


Pass the floor anchor of the front seat outer seat belt assembly LH through the center pillar upper garnish LH.


b.

Engage the clip and guide to install the center pillar upper garnish LH as shown in the illustration.


c.

Install the 2 screws.


Hide 62411B 23.INSTALL CENTER PILLAR UPPER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 62414A 24.INSTALL CENTER PILLAR LOWER GARNISH LH

a.
B487757C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 claws, 2 clips and 2 guides to install the center pillar lower garnish LH as shown in the illustration.


Hide 62413A 25.INSTALL CENTER PILLAR LOWER GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 73220 26.CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH

a.

Connect the front seat outer belt assembly LH with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73210 27.CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 62332A 28.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

a.
B487758C01
1.208,0.688 0.979,0.74 false 2.292,0.823 2.49,1.146 true 1.25,0.573 1.563,0.771 0.313,0.198 10 false *a 2.552,1.073 2.865,1.271 0.313,0.198 10 false *b
*a Paint Mark
*b Flange Position


Align the paint mark on the rear door opening trim weatherstrip LH with the flange position on the vehicle body and install the rear door opening trim weatherstrip LH.

Paint Mark:
Area Color
RH Side White
LH Side Gold


NOTICE:

After installation, check that the corners fit correctly.



Hide 62331A 29.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 67918A 30.INSTALL REAR DOOR SCUFF PLATE LH

a.
B487759C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 5 claws and guide to install the rear door scuff plate LH as shown in the illustration.


Hide 67917A 31.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 62212 32.INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

a.

Remove the protective cover.


b.

for LH side:

i.

Connect the connector to connect the No. 1 roof wire.


ii.

Engage the 4 clamps.



c.

for RH side:

i.

Engage the hook to connect the No. 2 antenna cord sub-assembly.


ii.

Install the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


iii.

Connect the connector.


iv.

Engage the 3 clamps.



d.

Install a new front pillar garnish clip to the front pillar garnish LH.

HINT:

Install the front pillar garnish clip so that it is oriented as shown in the illustration.

B485707C01
1.594,0.781 1.927,0.781 false 2,1.51 2.333,1.51 false 2,0.708 2.313,0.865 0.313,0.156 10 false *1 2.385,1.427 2.698,1.583 0.313,0.156 10 false *2
*1 Front Pillar Garnish Clip *2 Front Pillar Garnish LH




e.
B484558C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 2 guides, clip and front pillar garnish clip to install the front pillar garnish LH as shown in the illustration.


Hide 62211 33.INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

HINT:

Use the same procedure as for the LH side.


Hide 62212 34.INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

a.

for LH side:

i.

Connect the connector to connect the No. 1 roof wire.


ii.

Engage the 4 clamps.



b.

for RH side:

i.

Engage the hook to connect the No. 2 antenna cord sub-assembly.


ii.

Install the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


iii.

Connect the connector.


iv.

Engage the 4 clamps.



c.
B489631C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Engage the 2 guides and 2 clips to install the front pillar garnish LH as shown in the illustration.


Hide 62211 35.INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure as for the LH side.


Hide 62312B 36.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B487761C01
1,0.729 1.219,0.656 false 2.385,1.156 2.271,0.833 true 1.281,0.563 1.594,0.76 0.313,0.198 10 false *a 2.458,1.083 2.771,1.281 0.313,0.198 10 false *b
*a Paint Mark
*b Flange Position


Align the paint mark on the front door opening trim weatherstrip LH with the flange position on the vehicle body and install the front door opening trim weatherstrip LH.

Paint Mark:
Area Color
RH Side Yellow
LH Side Orange


NOTICE:

After installation, check that the corners fit correctly.



Hide 62311B 37.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62112 38.INSTALL COWL SIDE TRIM BOARD LH

a.
B487762C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 2 clips to install the cowl side trim board LH as shown in the illustration.


b.

Install the clip.


Hide 62111C 39.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 67914 40.INSTALL FRONT DOOR SCUFF PLATE LH

a.
B487763C01
0,0 0,0 false
V113147

Install in this Direction


Engage the 8 claws to install the front door scuff plate LH as shown in the illustration.


Hide 67913 41.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 42.INSTALL REAR SEAT ASSEMBLY (for Separate Seat Type)

Hide 43.INSTALL REAR SEAT ASSEMBLY (for Fold Down Seat Type)

Hide 64773B 44.INSTALL NO. 2 SPARE WHEEL COVER PAD

a.

Install the No. 2 spare wheel cover pad.


Hide 64772 45.INSTALL SPARE WHEEL COVER PAD

a.

Install the spare wheel cover pad.


Hide 58410B 46.INSTALL DECK BOARD ASSEMBLY

a.

Install the deck board assembly.


Hide 64711E 47.INSTALL LUGGAGE COMPARTMENT FLOOR MAT

a.

Install the luggage compartment floor mat.


Hide 64330 48.INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY

a.

Engage the 2 guides to install the package tray trim panel assembly.


b.

Install the 2 suspenders onto the package tray trim hanger.