The ECM determines the vehicle inclination based on a signal from the airbag ECU assembly (yaw rate and acceleration sensor). If a malfunction of the airbag ECU assembly (yaw rate and acceleration sensor) is determined based on a malfunction signal from the brake actuator assembly (skid control ECU), the ECM stores this DTC.
The airbag ECU assembly (yaw rate and acceleration sensor) signal is sent to the brake actuator assembly (skid control ECU) via CAN communication.
If CAN communication DTCs are output, perform troubleshooting for those DTCs first.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P1586 | Acceleration Sensor Malfunction | After the ignition switch is turned ON, the brake actuator assembly (skid control ECU) has detected either one of the following conditions, and the ECM has received a diagnostic signal from the brake actuator assembly (skid control ECU) for 3 seconds or more (1 trip detection logic).
·
While the vehicle is driven at 30 km/h (19 mph) or more, the difference between the calculated longitudinal G value based on the airbag sensor assembly (yaw rate and acceleration sensor) (G sensor) and the value based the vehicle speed exceeds 0.35 G for 60 seconds or more. ·
Airbag sensor assembly (yaw rate and acceleration sensor) signal does not change 16 times or more while the vehicle speed decreases from 30 km/h (19 mph) to 0 km/h (0 mph). |
·
Airbag ECU assembly (Yaw rate and acceleration sensor) ·
CAN communication system ·
Brake actuator assembly (Skid control ECU) |
Does not come on | DTC stored |
Refer to DTC P1585
Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>P1585
Perform initialization after replacing any parts related to the continuously variable transaxle system.
Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>INITIALIZATION
Check that no DTCs are stored after performing initialization.
Click hereDrivetrain>K411 CVT>CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM>DTC CHECK / CLEAR
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U0129 is not output | A |
| DTC U0129 is output | B |
A
B
Connect the GTS to the DLC3.
Turn the GTS on.
Turn the ignition switch to ON.
Clear the DTCs.
Perform a road test where the vehicle is driven at 30 km/h (19 mph) or more, the brakes are applied at least 16 times and the vehicle is finally stopped.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the GTS.
If any DTCs other than P1586 are output, perform troubleshooting for those DTCs first.
| Result | Proceed to |
|---|---|
| Only DTC P1586 is output | A |
| DTC P1586 and other DTCs are output | B |
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
| Tester Display |
|---|
| G Sensor |
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| G Sensor | Converted output voltage of G sensor | Min.: 0 V
Max.: 79.998 V |
·
2.31 to 2.69 V: Vehicle on level ground ·
1.88 to 2.5 V: Decelerating ·
2.5 to 3.11 V: Accelerating ·
Stuck at 1.87 V: G sensor malfunction ·
Stuck at 1.87 V: Communication malfunction |
- |
| Result | Proceed to |
|---|---|
| Data List value is not normal | A |
| Data List value is normal | B |
A
B
Replace the airbag ECU assembly (yaw rate and acceleration sensor).
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>COMPONENTS
| Proceed to |
|---|
| NEXT |
NEXT