READ DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Cruise Control / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| CCS Vehicle Spd | Vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual vehicle speed | - |
| CCS Mem Vehicle Spd | Stored vehicle speed | Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) | Actual stored vehicle speed | - |
| Throttle Opening Angle | Required throttle opening amount | Min.: 0°, Max.: 124.5° | Actual required throttle opening amount | - |
| Cruise Control | Cruise control system active condition | ON or OFF | ON: Cruise control activated
OFF: Cruise control deactivated |
- |
| Cruise Main Switch Operation Condition | Cruise control main switch status | ON or OFF | ON: Cruise control main switch (ON-OFF button) pushed
OFF: Cruise control main switch (ON-OFF button) released |
- |
| Main SW M-CPU | Cruise control main switch signal (Main CPU) | ON or OFF | ON: Cruise control main switch (ON-OFF button) pushed
OFF: Cruise control main switch (ON-OFF button) released |
- |
| CCS Ready M-CPU | Cruise control system standby condition (Main CPU) | ON or OFF | Each time cruise control main switch (ON-OFF button) is pushed, ON/OFF changes | - |
| CCS Indicator M-CPU | Cruise control indicator illumination signal (Main CPU) | ON or OFF | ON: Cruise control indicator illuminated in green
OFF: Cruise control indicator not on |
- |
| Cancel Switch | CANCEL switch signal | ON or OFF | ON: CANCEL switch on
OFF: CANCEL switch off |
- |
| SET/COAST Switch | -/SET switch signal | ON or OFF | ON: -/SET switch on
OFF: -/SET switch off |
- |
| RES/ACC Switch | +/RES switch signal | ON or OFF | ON: +/RES switch on
OFF: +/RES switch off |
- |
| Stop Light Switch 1 | Stop light switch signal | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Stop Light Switch 2 | Stop light switch signal | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
| Cruise Operation Status | Transmission range sensor signal | ON or OFF | ON: Cruise control operated
OFF: Cruise control operation stopped |
- |
| Brake Cancel Switch | Brake cancel signal | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
- |
If any DTCs are output, the value for a measurement item may be incorrect.
If any DTCs are output, perform troubleshooting accordingly. After repair, confirm relevant values using Data List.
PERFORM ACTIVE TEST
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Combination Meter / Active Test.
Perform "Active Test" according to the display on GTS.
The ignition switch must be turned on to proceed with the Active Test using the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Indicat. Lamp Cruise | Cruise control indicator | Cruise control indicator ON / OFF | w/o Multi-information Display |
| Indicat. SET | Cruise control SET indicator | Cruise control SET indicator ON / OFF | w/o Multi-information Display |
| Cruise Indicator | Cruise control indicator | Cruise control indicator ON / OFF | w/o Multi-information Display |
| Meter Display 1 | Multi-information display | Multi-information display OFF, 6 to 0 or All | w/ Multi-information Display |
| Meter Display 2 | Multi-information display | Multi-information display OFF, 9 to 7 | w/ Multi-information Display |