CHECK COMBINATION METER ASSEMBLY
Disconnect the F38 and F39 combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F38-40 (B) - Body ground | B - Body ground | Battery power supply | Always | 11 to 14 V |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F38-1 (B) - Body ground | B - Body ground | Battery power supply | Always | 11 to 14 V |
If the result is not as specified, there may be a malfunction in the wire harness.
Reconnect the F38 and F39 combination meter assembly connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F39-3 (HAZ) - Body ground | P - Body ground | Hazard warning signal switch input | Hazard warning signal switch off | 11 to 14 V |
| Hazard warning signal switch on | Below 1 V | |||
| F39-9 (ER) - Body ground | L - Body ground | Turn signal switch right signal input | Ignition switch ON, turn signal switch in neutral position | 11 to 14 V |
| Ignition switch ON, turn signal switch in right turn position | Below 1 V | |||
| F39-10 (EL) - Body ground | GR - Body ground | Turn signal switch left signal input | Ignition switch ON, turn signal switch in neutral position | 11 to 14 V |
| Ignition switch ON, turn signal switch in left turn position | Below 1 V |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F38-16 (PKBI) - Body ground | L - Body ground | Parking brake switch input | Input parking brake switch on | Below 1 V |
| Input parking brake switch off | 11 to 14 V | |||
| F38-13 (DRLE) -Body ground*1 | B - Body ground | DRL relay drive output | Ignition switch ON, daytime running light on | Below 1 V |
| Ignition switch ON, daytime running light off | 11 to 14 V | |||
| F39-11 (HAZ) - Body ground | P - Body ground | Hazard warning signal switch input | Hazard warning signal switch off | 11 to 14 V |
| Hazard warning signal switch on | Below 1 V | |||
| F39-9 (ER) - Body ground | L - Body ground | Turn signal switch right signal input | Ignition switch ON, turn signal switch in neutral position | 11 to 14 V |
| Ignition switch ON, turn signal switch in right turn position | Below 1 V | |||
| F39-10 (EL) - Body ground | GR - Body ground | Turn signal switch left signal input | Ignition switch ON, turn signal switch in neutral position | 11 to 14 V |
| Ignition switch ON, turn signal switch in left turn position | Below 1 V |
*1: w/ Daytime Running Light
If the result is not as specified, the combination meter assembly may be malfunctioning.
CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY AND BODY COMPUTER(for TMT Made)
| *1 | Driver Side Junction Block Assembly | - |
| *1 | Body Computer | - |
Remove the body computer from the driver side junction block assembly.
Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for TMT Made)>REMOVAL
Reconnect the driver side junction block assembly connectors
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| MB-6 (BECU) - Body ground | - | Battery power supply | Always | 11 to 14 V |
| MB-7 (IG) - Body ground | - | IG power supply | Ignition switch ON | 11 to 14 V |
| MB-1 (GND) - Body ground | - | Ground | Always | Below 1 Ω |
| MB-18 (DCTY) - Body ground*1 | - | Front door LH courtesy light switch input | Front door LH open | Below 1 V |
| Front door LH closed | Pulse generation | |||
| MB-18 (DCTY) - Body ground*2 | - | Front door RH courtesy light switch input | Front door RH open | Below 1 V |
| Front door RH closed | Pulse generation |
*1: for LHD
*2: for RHD
Reinstall the body computer to the driver side junction block assembly.
Measure the voltage and check for pulses according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| F52-1 (TRLY) - Body ground | B - Body ground | TAIL relay drive output | Taillights on | Below 2 V |
| Taillights off | 11 to 14 V | |||
| F52-6 (HAZ) - Body ground | P - Body ground | Hazard drive output | Hazard warning signal switch off | 11 to 14 V |
| Hazard warning signal switch on | Below 1 V | |||
| F125-4 (CLTS) - Body ground | P - Body ground | Automatic light control sensor signal input | Ignition switch off | Below 1 V |
| Ignition switch ON, automatic light control system operating | Pulse generation
(See waveform 1) |
|||
| F125-5 (CLTB) - F125-3 (CLTE) | W - V | Automatic light control sensor power supply output | Headlight dimmer switch (light control switch) in AUTO position | 11 to 14 V |
| F125-6 (A) - Body ground | G - Body ground | Headlight dimmer switch (light control switch) AUTO signal input | Headlight dimmer switch (light control switch) not in AUTO position | 11 to 14 V |
| Headlight dimmer switch (light control switch) in AUTO position | Below 1 V | |||
| F125-7 (TAIL) - Body ground | B - Body ground | Headlight dimmer switch (light control switch) tail signal input | Headlight dimmer switch (light control switch) in neither tail nor head position | 11 to 14 V |
| Headlight dimmer switch (light control switch) in tail or head position | Below 1 V | |||
| F125-8 (HEAD) - Body ground | LG - Body ground | Headlight dimmer switch (light control switch) head signal input | Headlight dimmer switch (light control switch) not in head position | 11 to 14 V |
| Headlight dimmer switch (light control switch) in head position | Below 1 V | |||
| F125-9 (RFOG) - Body ground*1 | B - Body ground | Rear fog light switch input | Headlight dimmer switch (light control switch) in tail or head position and front fog light switch off | 11 to 14 V |
| Headlight dimmer switch (light control switch) in head or front fog light position and switch on | Below 1 V | |||
| F125-10 (FFOG) - Body ground*2 | R - Body ground | Front fog light switch input | Front fog light switch off | 11 to 14 V |
| Front fog light switch on | Below 1 V | |||
| F125-13 (HF) - Body ground | R - Body ground | Headlight dimmer switch high flash signal input | Headlight dimmer switch not in high flash position | 11 to 14 V |
| Headlight dimmer switch in high flash position | Below 1 V | |||
| F125-14 (HU) - Body ground | Y - Body ground | Headlight dimmer switch high signal input | Headlight dimmer switch in low position | 11 to 14 V |
| Headlight dimmer switch in high position | Below 1 V | |||
| 6N-6 (RFGO) - Body ground*1 | B - Body ground | RR FOG relay drive output | Headlight dimmer switch (light control switch) in head or front fog light position and rear fog light switch off | 11 to 14 V |
| Headlight dimmer switch (light control switch) in head or front fog light position and switch on | Below 1 V | |||
| 6N-9 (FFGO) - Body ground*2 | R - Body ground | FR FOG relay drive output | Headlight dimmer switch (light control switch) in tail or head position and front fog light switch off | 11 to 14 V |
| Headlight dimmer switch (light control switch) in tail or head position and front fog light switch on | Below 1 V | |||
| 6D-2 (HRLY) - Body ground | R - Body ground | H-LP relay drive output | Headlight dimmer switch (light control switch) in head position | Below 1 V |
| Headlight dimmer switch (light control switch) not in head position | 11 to 14 V | |||
| 6D-4 (DIM) - Body ground | BE - Body ground | DIM relay drive output | Headlight dimmer switch (dimmer switch) in high or high flash position | Below 1 V |
| Headlight dimmer switch (dimmer switch) not in high or high flash position | 11 to 14 V |
*1: w/ Rear Fog Light
*2: w/ Front Fog Light