Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for TMT Made) › 2017.10–2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0333397 POWER STEERING SYSTEM(for TMT Made) U

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for TMT Made)  TERMINALS OF ECU  


CHECK POWER STEERING ECU ASSEMBLY


C228662E09
4.417,0.25 4.833,0.5 0.417,0.25 1.917,0.25 2.333,0.5 0.417,0.25 3.25,0.25 3.667,0.5 0.417,0.25 2.5,0.25 2.833,0.5 0.333,0.25 4.51,0.302 4.823,0.458 0.313,0.156 10 false F11 2.01,0.292 2.333,0.5 0.323,0.208 10 false F12 2.594,0.292 2.813,0.469 0.219,0.177 10 false z5 3.375,0.281 3.583,0.469 0.208,0.188 10 false z9

a.

Measure the voltage and resistance according to the value(s) in the table below.

NOTICE:
·

Check if the power steering ECU assembly connectors are securely connected by pulling on them from the backside.

·

If the EPS warning light is illuminated due to a malfunction, the fail-safe function may cause the voltage of the power steering ECU's terminals to become 0 V.



Terminals No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
F12-1 (IG) - Body ground L - Body ground IG power source voltage Ignition switch ON 11 to 14 V
F12-6 (TS) - Body ground GR - Body ground Test mode signal Always 11 to 14 V
F12-7 (CANH) - F12-8 (CANL) B - W CAN communication line Ignition switch off 54 to 69 Ω
z5-1 (TRQ2) - z5-2 (TRQG) Y - B Torque sensor 2 input signal Engine running and steering wheel not being turned (without load) 2.3 to 2.7 V
Engine running and steering wheel being turned to right with vehicle stopped 1.2 to 2.5 V
Engine running and steering wheel being turned to left with vehicle stopped 2.5 to 3.8 V
z5-2 (TRQG) - Body ground B - Body ground Torque sensor ground Always Below 1 Ω
z5-8 (TRQV) - z5-2 (TRQG) R - B Torque sensor power source Ignition switch ON 4.5 to 5.5 V
z5-9 (TRQ1) - z5-2 (TRQG) W - B Torque sensor 1 input signal Engine running and steering wheel not being turned (without load) 2.3 to 2.7 V
Engine running and steering wheel being turned to right with vehicle stopped 2.5 to 3.8 V
Engine running and steering wheel being turned to left with vehicle stopped 1.2 to 2.5 V
z9-1 (M1) - Body ground R - Body ground Power steering motor assembly output signal 1 Engine running and steering wheel being turned to right 11 to 14 V
Engine running and steering wheel being turned to left 6 to 11 V
z9-2 (M2) - Body ground B - Body ground Power steering motor assembly output signal 2 Engine running and steering wheel being turned to right 6 to 11 V
Engine running and steering wheel being turned to left 11 to 14 V
F12-9 (IDUP) - Body ground B - Body ground ECM Ignition switch ON 5 to 14 V
F11-1 (PIG) - Body ground B - Body ground Power steering motor assembly power supply input signal Always 11 to 14 V
F11-2 (PGND) - Body ground W-B - Body ground Power ground Always Below 1 Ω

If the result is not as specified, the ECU may have a malfunction.