DATA LIST
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / EMPS / Data List.
According to the display on the GTS, read the "Data List".
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Meter Vehicle Velocity | Vehicle speed from speedometer | Min.: 0.0 km/h (0.0 mph)
Max.: 300.0 km/h (186.4 mph) |
·
0 km/h (0 mph): Engine running and vehicle stopped ·
No significant fluctuation: Engine running and vehicle driven at constant speed |
- |
| Engine Revolution | Engine speed | Min.: 0 rpm
Max.: 12800 rpm |
Engine running at a constant speed: No significant fluctuation | - |
| Motor Actual Current | Current to motor | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort
-The value increases when turning left and decreases when turning right |
Engine running and steering wheel being turned |
| Command Value Current | Requested current to motor | Min.: -327.68 A
Max.: 327.67 A |
Value changes in proportion to steering effort
-The value increases when turning left and decreases when turning right |
Engine running and steering wheel being turned |
| Thermistor Temperature | ECU substrate temperature | Min.: -50.0°C (-58.0°F)
Max.: 150.0°C (302.0°F) |
-50 to 150°C (-58 to 302°F) | - |
| PIG Power Supply | Power source voltage to active motor | Min.: 0.0000 V
Max.: 20.1531 V |
11 to 14 V | Always |
| IG Power Supply | IG power source voltage | Min.: 0.0000 V
Max.: 20.1531 V |
11 to 14 V | Ignition switch ON |
| Steering Angle Sens Sig | Steering angle sensor signal state | OK or NG(1) or NG(2) or NG(3) | OK: Steering angle sensor signal received
NG(1): The learning has not completed NG(2): Steering angle sensor abnormal NG(3): Communication Error |
- |
| Steering Wheel Torque | Steering wheel torque | Min.: -7.00 Nm
Max.: 7.00 Nm |
Value changes in proportion to steering effort | Engine running and steering wheel being turned |
| Torque Sensor 1 Output | Torque sensor 1 output value | Min.: 0.0000 V
Max.: 4.9725 V |
·
2.3 to 2.7 V: Engine running and steering wheel not being turned (without load) ·
2.5 to 3.8 V: Engine running and steering wheel being turned to right with vehicle stopped ·
1.2 to 2.5 V: Engine running and steering wheel being turned to left with vehicle stopped |
- |
| Torque Sensor 2 Output | Torque sensor 2 output value | Min.: 0.0000 V
Max.: 4.9725 V |
·
2.3 to 2.7 V: Engine running and steering wheel not being turned (without load) ·
1.2 to 2.5 V: Engine running and steering wheel being turned to right with vehicle stopped ·
2.5 to 3.8 V: Engine running and steering wheel being turned to left with vehicle stopped |
- |
| TRQ1 Zero Point Value | Zero point value of torque sensor 1 | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V | Engine running and steering wheel not being turned (without load) |
| TRQ2 Zero Point Value | Zero point value of torque sensor 2 | Min.: 0.0000 V
Max.: 4.9725 V |
2.3 to 2.7 V | Engine running and steering wheel not being turned (without load) |
| Motor Terminal Volt(+) | Motor terminal M1 voltage | Min.: 0.0 V
Max.: 25.5 V |
·
11 to 14 V: Engine running and steering wheel being turned to right ·
6 to 11 V: Engine running and steering wheel being turned to left |
- |
| Motor Terminal Volt(-) | Motor terminal M2 voltage | Min.: 0.0 V
Max.: 25.5 V |
·
6 to 11 V: Engine running and steering wheel being turned to right ·
11 to 14 V: Engine running and steering wheel being turned to left |
- |
| IG ON/OFF Times | Number of times of ignition switch ON/off after fail detection | Min.: 0 times
Max.: 65535 times |
- | This value indicates the number of times of IG on/off after the latest DTC detection. |
| Motor Overheat Record | Continuous overheat prevention control record | Unrec or Rec | Unrec | Unrec: Unrecorded
Rec: Recorded |
| Motor Lo Power Record | PIG power source voltage drop record | Unrec or Rec | Unrec | Unrec: Unrecorded
Rec: Recorded |
| Eng Rev Inter Record | Record of ignition switch ON signal interruption | Unrec or Rec | Unrec | Unrec: Unrecorded
Rec: Recorded |
| Str Angle Inter Record | Record of steering sensor signal interruption occurrence display | Unrec or Rec | Unrec | Unrec: Unrecorded
Rec: Recorded |
| Spd Sig Invalid Record | Vehicle speed signal invalid record | Unrec or Rec | Unrec | Unrec: Unrecorded
Rec: Recorded |
| Battery Voltage Lo Record | Battery voltage reduction history | Min.: 0 times
Max.: 65535 times |
0 to 65535 times | - |
| Stop&Start Ctrl Mode | Status of the record of stop and start control mode | IG, Run, Stopreq, Stop, Restart | IG: Ignition switch ON (Before engine started)
Run: Engine running Stopreq: Engine stop requested Stop: Engine stopped Restart: Engine restarting |
This item is displayed on the GTS but is not used. |
| Motor Overheat Limit Cnt(Normal) | Number of times that assist limit was performed according to the estimated temperature of the portion where heat was generated in the power steering ECU assembly and motor coil | Min.: 0 times
Max.: 255 times |
- | - |
| Assist Limit Cnt(Power Voltage Low) | Number of times that assist limit was performed due to battery voltage having dropped to 9 V or below | Min.: 0 times
Max.: 255 times |
- | - |
| Power Vol Low Prevention Limit Cnt | Number of times that assist limit was performed due to battery voltage having dropped to 9.7 V or below | Min.: 0 times
Max.: 255 times |
- | - |
| Eng Stall/Ready OFF Cnt | Number of times that assist limit was performed after the engine stalled and the ignition switch was turned off | Min.: 0 times
Max.: 255 times |
- | - |
| Motor Overheat Limit Cnt(Motor Overload) | Number of times that assist limit was performed to prevent the system from overheating in a case where the motor is overloaded because it is locked due to the steering wheel being turned to the full lock position or a tire hitting a curb | Min.: 0 times
Max.: 255 times |
- | - |
| Assist Limit Cnt(Vehicle Spd Sig Malf) | Number of times that assist power was set to a value suitable for high-speed driving when driving at high speeds due to an abnormal vehicle speed signal | Min.: 0 times
Max.: 255 times |
- | - |
| Assist Limit Record 1 | Information of assist limit that was used in the past or is currently in use (latest history) | Unrec, Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF, Mtr Overload, DC-DC Malf, Vhcl Spd Sig Malf, Batt Vol Keep | - | - |
| Record 1 Key Cycle | Number of times that the ignition switch was turned ON before Assist Limit Record 1 was stored | Min.: 0 times
Max.: 65535 times |
- | - |
| Record 1 Key Cycle Elapsed Time | Period of time that elapsed after the ignition switch was turned ON before Assist Limit Record 1 was stored | Min.: 0.0 s
Max.: 53687091.1 s |
- | - |
| Assist Limit Record 2 | Information of assist limit that was used in the past (second latest history) | Unrec, Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF, Mtr Overload, DC-DC Malf, Vhcl Spd Sig Malf, Batt Vol Keep | - | - |
| Record 2 Key Cycle | Number of times that the ignition switch was turned ON after Assist Limit Record 2 was stored before Assist Limit Record 1 was stored | Min.: 0 times
Max.: 65535 times |
- | - |
| Record 2 Key Cycle Elapsed Time | Period of time that elapsed after the ignition switch was turned ON before Assist Limit Record 2 was stored | Min.: 0.0 s
Max.: 53687091.1 s |
- | - |
| Assist Limit Record 3 | Information of assist limit that was used in the past (third latest history) | Unrec, Mtr Overheat, Pow Vol Low, Pow Vol Low Prevent, Eng Stall, Ready OFF, Mtr Overload, DC-DC Malf, Vhcl Spd Sig Malf, Batt Vol Keep | - | - |
| Record 3 Key Cycle | Number of times that the ignition switch was turned ON after Assist Limit Record 3 was stored before Assist Limit Record 2 was stored | Min.: 0 times
Max.: 65535 times |
- | - |
| Record 3 Key Cycle Elapsed Time | Period of time that elapsed after the ignition switch was turned ON before Assist Limit Record 3 was stored | Min.: 0.0 s
Max.: 53687091.1 s |
- | - |
| Current Key Cycle | Number of current trip | Min.: 0 times
Max.: 65535 times |
- | - |
| Current Key Cycle Elapsed Time | Time elapsed since ignition switch was turned ON | Min.: 0.0 s
Max.: 53687091.1 s |
- | - |
| Steering Angle | Steering angle value | Min.: -3072.0 deg
Max.: 3070.5 deg |
- | During steering operation: Changes in proportion with steering wheel rotation |
| The Number of DTCs | Number of detected DTCs when freeze frame data stored | Min.: 0
Max.: 255 |
0 to 255 | - |
With the vehicle stopped or driving very slowly, if the steering wheel is turned repeatedly or turned to a lock position and the vehicle is driven for an extended period of time, the amount of power assist is decreased to prevent overheating of the motor and ECU. If this occurs, idle the engine and do not turn the steering wheel for approximately 10 minutes to improve power assist a little.
If the battery is not sufficiently charged or the voltage decreases temporarily, the amount of power assist is reduced and the EPS warning light comes on. In such cases, the amount of power assist returns to normal when the battery voltage recovers.