Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for TMT Made) › 2017.10–2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0333397 POWER STEERING SYSTEM(for TMT Made) C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for TMT Made)  C1553  PIG Power Supply Overvoltage  


DESCRIPTION

If the power steering ECU assembly determines that the motor power source voltage and the IG voltage are not within the specified range, it stops the power assist as a fail-safe function.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition Note
C1553 PIG Power Supply Overvoltage
·

PIG power source overvoltage

·

IG power source overvoltage


·

EPS fuse

·

EPS-IG fuse

·

IG and PIG power source circuits

·

Power steering ECU assembly


EPS warning light: Comes on After normal confirmation -

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C280668E01
0.781,0.729 1.573,1 0.792,0.271 10 false from Battery 0.656,1.375 1.573,1.604 0.917,0.229 10 false from IG Circuit 3.563,0.885 3.927,1.167 0.365,0.281 10 false EPS 3.458,1.552 4,1.823 0.542,0.271 10 false EPS-IG 5.552,0.75 5.865,0.969 0.313,0.219 10 false F11 5.552,1.385 5.865,1.604 0.313,0.219 10 false F12 5.552,2.052 5.865,2.271 0.313,0.219 10 false F11 5.906,0.75 6.271,1.031 0.365,0.281 10 false PIG 5.917,1.396 6.281,1.677 0.365,0.281 10 false IG 5.938,2.073 6.427,2.365 0.49,0.292 10 false PGND 5.656,0.552 5.813,0.708 0.156,0.156 10 false 1 5.635,1.167 5.792,1.323 0.156,0.156 10 false 1 5.635,1.865 5.792,2.021 0.156,0.156 10 false 2 5.74,3.063 7.042,3.458 1.302,0.396 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly has been replaced, perform assist map writing and torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BATTERY - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the power steering ECU assembly connectors.


b.
C349135C05
0.333,0.833 0.833,1.083 0.5,0.25 0.333,3.417 0.833,3.667 0.5,0.25 0.958,1.615 1.427,1.302 true 0.969,4 1.385,3.583 true 2.417,4.021 2.042,3.615 true 0.083,0.083 0.333,0.333 0.25,0.25 10 false *a 0.469,0.875 0.927,1.073 0.458,0.198 10 false F12 0.75,1.615 1.063,1.813 0.313,0.198 10 false IG 0.76,4.052 1.219,4.25 0.458,0.198 10 false PIG 0.469,3.458 0.927,3.656 0.458,0.198 10 false F11 2.333,4.073 2.854,4.26 0.521,0.188 10 false PGND
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F12-1 (IG) - F11-2 (PGND) Ignition switch ON 11 to 14 V
F11-1 (PIG) - F11-2 (PGND) Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR