Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for TMT Made) › 2017.10–2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0333397 POWER STEERING SYSTEM(for TMT Made) D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for TMT Made)  TEST MODE PROCEDURE  


SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (USING THE GTS)


NOTICE:

Torque sensor zero point calibration is performed automatically when the test mode inspection is conducted after the power steering ECU assembly has been replaced with a new one.


HINT:
·

Speed sensor signals can be checked easily in test mode.

·

Test mode DTCs C1571 are stored during the transition to test mode. These DTCs do not indicate a malfunction since the DTCs will be cleared if the ECU determines that the sensor is normal.

·

The test mode DTCs are cleared simultaneously when test mode is terminated.



a.

Enter Test Mode

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Start the engine.


iv.

Turn the GTS on.


v.

Enter the following menus: Chassis / EMPS / Utility / Signal Check.



b.

Check that the EPS warning light comes on for several seconds and then blinks in the test mode pattern (0.125 seconds on and 0.125 seconds off).

NOTICE:

If torque sensor zero point calibration has not been performed, the EPS warning light comes on until torque sensor zero point calibration is completed, and blinks in the test mode pattern after torque sensor zero point calibration is completed.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>CALIBRATION



c.

Check engine speed signal.

i.

Drive the vehicle and accelerate until the vehicle speed reaches 10 km/h (6 mph) or more.

C233686E05
0.25,0.167 2.063,0.427 1.813,0.26 10 false When system is normal: 1.917,0.854 2.854,1.063 0.938,0.208 10 false km/h (mph) 0.542,1.552 1.625,1.729 1.083,0.177 10 false Vehicle Speed 2.115,1.365 2.604,1.552 0.49,0.188 10 false 10 (6) 2.25,1.927 2.552,2.094 0.302,0.167 10 false 0 0.542,2.708 1.844,3.063 1.302,0.354 10 false EPS Warning Light 1.938,2.594 2.313,2.75 0.375,0.156 10 false On 1.938,2.865 2.354,3.031 0.417,0.167 10 false Off 3.76,3.125 6.958,3.344 3.198,0.219 10 false Light blinks until test mode DTC C1571 is cleared. 6.042,1.938 6.635,2.125 0.594,0.188 10 false Time 2.115,1.656 2.604,1.844 0.49,0.188 10 false 4 (2.5) 3.76,3.438 6.563,3.646 2.802,0.208 10 false Light goes off at 10 km/h (6 mph) or more. 1.708,3.26 2.688,3.448 0.979,0.188 10 false 0.125 seconds 2.76,3.271 3.74,3.458 0.979,0.188 10 false 0.125 seconds



d.

Check the DTCs in test mode.

Test Mode DTC Test Signal Test Mode DTC Clear Condition Trouble Areas
C1571 Vehicle speed signal Vehicle speed 10 km/h (6 mph) or more If the DTC cannot be cleared, any of the following areas may be malfunctioning:
·

CAN communication system

·

Combination meter assembly

·

Power steering ECU assembly



NOTICE:

Test mode DTCs are cleared when test mode is terminated.




SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (USING SST CHECK WIRE)


NOTICE:

Torque sensor zero point calibration is performed automatically when the test mode inspection is conducted after the power steering ECU assembly has been replaced with a new one.


HINT:
·

Speed sensor signals can be checked easily in test mode.


·

Test mode DTCs 71 are stored during the transition to test mode. These DTCs do not indicate a malfunction since the DTCs will be cleared if the ECU determines that the sensor is normal.


·

The test mode DTCs are cleared simultaneously when test mode is terminated.



a.

Enter Test Mode

i.

Turn the ignition switch off.


ii.
C248264C18
1.625,0.813 1.625,0.406 true 1.635,1.854 1.635,1.479 true 1.49,0.219 1.719,0.365 0.229,0.146 10 false CG 1.521,1.875 1.74,2.021 0.219,0.146 10 false TS 0.177,0.042 0.333,0.219 0.156,0.177 10 false *1
*1 DLC3


Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

SST
09843-18040  



b.

Check that the EPS warning light comes on for several seconds and then blinks in the test mode pattern (0.125 seconds on and 0.125 seconds off).

NOTICE:

If torque sensor zero point calibration has not been performed, the EPS warning light comes on until torque sensor zero point calibration is completed, and blinks in the test mode pattern after torque sensor zero point calibration is completed.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMT Made)>CALIBRATION



c.

Check engine speed signal.

i.

Drive the vehicle and accelerate until the vehicle speed reaches 10 km/h (6 mph) or more.

C233686E06
0.25,0.167 2.063,0.427 1.813,0.26 10 false When system is normal: 1.917,0.854 2.854,1.063 0.938,0.208 10 false km/h (mph) 0.542,1.552 1.625,1.729 1.083,0.177 10 false Vehicle Speed 2.115,1.365 2.604,1.552 0.49,0.188 10 false 10 (6) 2.25,1.927 2.552,2.094 0.302,0.167 10 false 0 0.542,2.708 1.896,3.083 1.354,0.375 10 false EPS Warning Light 1.938,2.594 2.313,2.75 0.375,0.156 10 false On 1.938,2.865 2.354,3.031 0.417,0.167 10 false Off 3.75,3.125 6.948,3.344 3.198,0.219 10 false Light blinks until test mode DTC 71 is cleared. 6.042,1.938 6.635,2.125 0.594,0.188 10 false Time 2.115,1.656 2.604,1.844 0.49,0.188 10 false 4 (2.5) 3.76,3.438 6.563,3.646 2.802,0.208 10 false Light goes off at 10 km/h (6 mph) or more. 1.708,3.26 2.688,3.448 0.979,0.188 10 false 0.125 seconds 2.76,3.271 3.74,3.458 0.979,0.188 10 false 0.125 seconds



d.

Check the DTCs in test mode.

Test Mode DTC Test Signal Test Mode DTC Clear Condition Trouble Areas
71 Vehicle speed signal Vehicle speed 10 km/h (6 mph) or more If the DTC cannot be cleared, any of the following areas may be malfunctioning:
·

CAN communication system

·

Combination meter assembly

·

Power steering ECU assembly



NOTICE:

Test mode DTCs are cleared when test mode is terminated.