Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for TMMIN Made) › 2017.10–2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0333419 POWER STEERING SYSTEM(for TMMIN Made) D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for TMMIN Made)  TEST MODE PROCEDURE  


SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (USING THE GTS)


NOTICE:

Torque sensor zero point calibration is performed automatically when the test mode inspection is conducted after the power steering ECU assembly has been replaced with a new one.


HINT:
·

Speed sensor signals can be checked easily in test mode.

·

Test mode DTCs C1571 and C1573 are stored during the transition to test mode. These DTCs do not indicate a malfunction since the DTCs will be cleared if the ECU determines that the sensor is normal.

·

The test mode DTCs are cleared simultaneously when test mode is terminated.



a.

Enter Test Mode

i.

Turn the ignition switch off.


ii.

Connect the GTS to the DLC3.


iii.

Start the engine.


iv.

Turn the GTS on.


v.

Enter the following menus: Chassis / EMPS / Utility / Signal Check.



b.

Check that the power steering warning light comes on for several seconds and then blinks in the test mode pattern (0.125 seconds on and 0.125 seconds off).

NOTICE:

If torque sensor zero point calibration has not been performed, the power steering warning light comes on until torque sensor zero point calibration is completed, and blinks in the test mode pattern after torque sensor zero point calibration is completed.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMMIN Made)>CALIBRATION



c.

Check vehicle speed signal and engine speed signal.

i.

Drive the vehicle and accelerate until the vehicle speed reaches 10 km/h (6 mph) or more.

HINT:

If the engine speed exceeds 300 rpm during this check, engine speed signals will also be checked simultaneously.


C233686E02
0.25,0.167 2.063,0.427 1.813,0.26 10 When system is normal: 1.917,0.854 2.854,1.063 0.938,0.208 10 km/h (mph) 0.542,1.552 1.625,1.729 1.083,0.177 10 Vehicle Speed 2.115,1.365 2.604,1.552 0.49,0.188 10 10 (6) 2.25,1.927 2.552,2.094 0.302,0.167 10 0 0.542,2.708 1.521,3.063 0.979,0.354 10 Power Steering Warning Light 1.938,2.594 2.313,2.75 0.375,0.156 10 On 1.938,2.865 2.354,3.031 0.417,0.167 10 Off 3.76,3.125 6.958,3.344 3.198,0.219 10 Light blinks until test mode DTC C1571 is cleared. 6.042,1.938 6.635,2.125 0.594,0.188 10 Time 2.115,1.656 2.604,1.844 0.49,0.188 10 4 (2.5) 3.76,3.438 6.563,3.646 2.802,0.208 10 Light goes off at 10 km/h (6 mph) or more. 1.708,3.26 2.688,3.448 0.979,0.188 10 0.125 seconds 2.76,3.271 3.74,3.458 0.979,0.188 10 0.125 seconds



d.

Check the DTCs in test mode.

Test Mode DTC Test Signal Test Mode DTC Clear Condition Trouble Areas
C1571 Vehicle speed signal Vehicle speed 10 km/h (6 mph) or more If the DTC cannot be cleared, any of the following areas may be malfunctioning:
·

Vehicle speed signal circuit

·

Combination meter assembly

·

Power steering ECU assembly


C1573 Engine speed signal Engine speed 300 rpm or more If the DTC cannot be cleared, any of the following areas may be malfunctioning:
·

Engine speed signal circuit

·

Power steering ECU assembly

·

ECM



NOTICE:

Test mode DTCs are cleared when test mode is terminated.




SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (USING SST CHECK WIRE)


NOTICE:

Torque sensor zero point calibration is performed automatically when the test mode inspection is conducted after the power steering ECU assembly has been replaced with a new one.


HINT:
·

Speed sensor signals can be checked easily in test mode.


·

Test mode DTCs C1571/71 and C1573/73 are stored during the transition to test mode. These DTCs do not indicate a malfunction since the DTCs will be cleared if the ECU determines that the sensor is normal.


·

The test mode DTCs are cleared simultaneously when test mode is terminated.



a.

Enter Test Mode

i.

Turn the ignition switch off.


ii.
C248264C18
1.625,0.813 1.625,0.406 true 1.635,1.854 1.635,1.479 true 1.49,0.219 1.719,0.365 0.229,0.146 10 false CG 1.521,1.875 1.74,2.021 0.219,0.146 10 false TS 0.177,0.042 0.333,0.219 0.156,0.177 10 false *1
*1 DLC3


Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.

SST
09843-18040  



b.

Check that the power steering warning light comes on for several seconds and then blinks in the test mode pattern (0.125 seconds on and 0.125 seconds off).

NOTICE:

If torque sensor zero point calibration has not been performed, the power steering warning light comes on until torque sensor zero point calibration is completed, and blinks in the test mode pattern after torque sensor zero point calibration is completed.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMMIN Made)>CALIBRATION



c.

Check vehicle speed signal and engine speed signal.

i.

Drive the vehicle and accelerate until the vehicle speed reaches 10 km/h (6 mph) or more.

HINT:

If the engine speed exceeds 300 rpm during this check, engine speed signals will also be checked simultaneously.


C233686E03
0.25,0.167 2.063,0.427 1.813,0.26 10 false When system is normal: 1.917,0.854 2.854,1.063 0.938,0.208 10 false km/h (mph) 0.542,1.552 1.625,1.729 1.083,0.177 10 false Vehicle Speed 2.115,1.365 2.604,1.552 0.49,0.188 10 false 10 (6) 2.25,1.927 2.552,2.094 0.302,0.167 10 false 0 0.542,2.708 1.521,3.063 0.979,0.354 10 false Power Steering Warning Light 1.938,2.594 2.313,2.75 0.375,0.156 10 false On 1.938,2.865 2.354,3.031 0.417,0.167 10 false Off 3.75,3.125 6.948,3.344 3.198,0.219 10 false Light blinks until test mode DTC 71 is cleared. 6.042,1.938 6.635,2.125 0.594,0.188 10 false Time 2.115,1.656 2.604,1.844 0.49,0.188 10 false 4 (2.5) 3.76,3.438 6.563,3.646 2.802,0.208 10 false Light goes off at 10 km/h (6 mph) or more. 1.708,3.26 2.688,3.448 0.979,0.188 10 false 0.125 seconds 2.76,3.271 3.74,3.458 0.979,0.188 10 false 0.125 seconds



d.

Check the DTCs in test mode.

Test Mode DTC Test Signal Test Mode DTC Clear Condition Trouble Areas
71 Vehicle speed signal Vehicle speed 10 km/h (6 mph) or more If the DTC cannot be cleared, any of the following areas may be malfunctioning:
·

Vehicle speed signal circuit

·

Combination meter assembly

·

Power steering ECU assembly


73 Engine speed signal Engine speed 300 rpm or more If the DTC cannot be cleared, any of the following areas may be malfunctioning:
·

Engine speed signal circuit

·

Power steering ECU assembly

·

ECM



NOTICE:

Test mode DTCs are cleared when test mode is terminated.