Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for TMMIN Made) › 2017.10–2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0333419 POWER STEERING SYSTEM(for TMMIN Made) D

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for TMMIN Made)  FREEZE FRAME DATA  


FREEZE FRAME DATA


a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Trouble Codes.


f.

According to the display on the GTS, select the freeze frame data.

Chassis > EMPS
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Torque Sensor 1 Output Torque sensor voltage Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V: The engine is running and steering wheel is not being turned (without load).
1.2 to 2.5 V: The engine is running and steering wheel is being turned to the left with vehicle stopped.
2.5 to 3.8 V: The engine is running and steering wheel is being turned to the right with vehicle stopped.
-
Torque Sensor 2 Output Torque sensor voltage Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V: The engine is running and steering wheel is not being turned (without load).
1.2 to 2.5 V: The engine is running and steering wheel is being turned to the right with vehicle stopped.
2.5 to 3.8 V: The engine is running and steering wheel is being turned to the left with vehicle stopped.
-
Meter Vehicle Velocity Vehicle speed from meter Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
·

0 km/h (0 mph)

·

No significant fluctuation.


·

The vehicle is stopped.

·

The vehicle is driven at a constant speed.


Engine Revolution Engine speed Min.: 0 rpm
Max.: 8160 rpm
No significant fluctuation. The engine is running at a constant speed.
Motor Actual Current Current to motor Min.: -128 A
Max.: 127 A
Value changes in proportion to steering effort. The engine is running and the steering wheel is being turned.
Command Value Current Amount of current requested for motor Min.: -128 A
Max.: 127 A
Value changes in proportion to steering effort. The engine is running and the steering wheel is being turned.
Thermistor Temperature ECU substrate temperature Min.: -50°C (-58°F)
Max.: 205°C (401°F)
- The ignition switch to ON.
PIG Power Supply Power source voltage to activate motor Min.: 0.0 V
Max.: 25.5 V
11 to 14 V The engine is running and the power steering is operating.
IG Power Supply ECU power source voltage Min.: 0.0 V
Max.: 25.5 V
11 to 14 V The ignition switch to ON.
TRQ1 Zero Point Value Zero point value of torque sensor 1 Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V The engine is running and the steering wheel is not being turned.
TRQ2 Zero Point Value Zero point value of torque sensor 2 Min.: 0.0000 V
Max.: 4.9725 V
2.3 to 2.7 V The engine is running and the steering wheel is not being turned.
Motor Terminal Volt(+) Motor terminal M1 voltage Min.: 0.0 V
Max.: 25.5 V
11 to 14 V: The engine is running and the steering wheel is being turned to the right.
6 to 11 V: The engine is running and the steering wheel is being turned to the left.
-
Motor Terminal Volt(-) Motor terminal M2 voltage Min.: 0.0 V
Max.: 25.5 V
6 to 11 V: The engine is running and the steering wheel is being turned to the right.
11 to 14 V: The engine is running and the steering wheel is being turned to the left.
-
Control Mode Codes indicating DTC detection timing during ECU control displayed in hexadecimal - - -