Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM(for TMMIN Made) › 2017.10–2018.01
RM30M0E _55 Steering _017103 POWER ASSIST SYSTEMS _0333419 POWER STEERING SYSTEM(for TMMIN Made) C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(for TMMIN Made)  C1551  IG Power Supply Voltage Malfunction  


DESCRIPTION

The power steering ECU assembly determines whether the ignition switch is ON or off through the IG power source circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area Return-to-normal Condition Note
C1551 IG Power Supply Voltage Malfunction An open or short in the IG power source circuit with the ignition switch ON.
·

EPS-IG fuse

·

IG power source circuit

·

Power steering ECU assembly


Ignition switch turned to ON again or after system confirmed to be normal Power Steering Warning Light comes on.

WIRING DIAGRAM

C113532E65
0.792,1.031 1.76,1.24 0.969,0.208 10 false from IG Circuit 3,1.24 3.594,1.479 0.594,0.24 10 false EPS-IG 4.438,1.031 4.729,1.177 0.292,0.146 10 false F12 4.802,1.042 4.969,1.188 0.167,0.146 10 false IG 4.531,0.865 4.625,1.01 0.094,0.146 10 false 1 4.458,2.135 4.75,2.281 0.292,0.146 10 false F11 4.802,2.146 5.229,2.292 0.427,0.146 10 false PGND 4.542,1.958 4.635,2.104 0.094,0.146 10 false 2 4.604,2.917 6.635,3.115 2.031,0.198 10 false Power Steering ECU Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

If the power steering ECU assembly, electric power steering column sub-assembly or power steering motor assembly have been replaced, perform torque sensor zero point calibration.

Click hereSteering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM(for TMMIN Made)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.READ VALUE USING GTS (IG POWER SUPPLY)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / EMPS / Data List.


f.

Select the item IG Power Supply in the Data List and read the value displayed on the GTS.

Chassis > EMPS > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
IG Power Supply ECU power source voltage Min.: 0.0 V
Max.: 25.5 V
11 to 14 V The ignition switch to ON.
Chassis > EMPS > Data List
Tester Display
IG Power Supply
50003 13 14
OK:

A value within the range listed in the normal condition column is displayed on the GTS.



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C232000C07
0.115,1.938 0.521,2.167 0.406,0.229 2.958,1.938 3.365,2.167 0.406,0.229 1.51,2.552 2.229,2.083 true 1.24,2 0.854,2.073 true 0.198,0.104 0.385,0.271 0.188,0.167 10 false *a 3.042,1.969 3.344,2.115 0.302,0.146 10 false F11 0.198,1.979 0.5,2.125 0.302,0.146 10 false F12 1.313,2.552 1.99,2.75 0.677,0.198 10 false PGND 1.281,1.896 1.698,2.083 0.417,0.188 10 false IG
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the power steering ECU assembly connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
F12-1 (IG) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F11-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR