Home › Engine / Hybrid System › 2NR-FE FUEL › FUEL TANK(for TMT Made) › from 2017.10
RM30M0E _51 Engine / Hybrid System _053553 2NR-FE FUEL _0265576 FUEL TANK(for TMT Made) A

2NR-FE FUEL  FUEL TANK(for TMT Made)  INSTALLATION  


PROCEDURE

Hide 77218A 1.INSTALL NO. 3 FUEL TANK FILLER PIPE SUPPORT

a.
A311728C01
0.719,0.281 1.031,0.479 0.313,0.198 10 false *a
*a Cutaway View
V100136

Front of Vehicle


Engage the clamp to install the No. 3 fuel tank filler pipe support to the fuel tank filler pipe assembly.


Hide 77216A 2.INSTALL NO. 1 FUEL TANK FILLER PIPE SUPPORT

a.
A311729C01
0.385,2.188 0.698,2.385 0.313,0.198 10 false *a
*a Cutaway View
V100136

Left Side of Vehicle


Install the No. 1 fuel tank filler pipe support to the fuel tank filler pipe assembly.


Hide 77217C 3.INSTALL NO. 2 FUEL TANK FILLER PIPE SUPPORT

a.
A311730C01
0.583,2.167 0.896,2.365 0.313,0.198 10 false *a
*a Cutaway View
V100136

Left Side of Vehicle


Engage the clamp to install the No. 2 fuel tank filler pipe support to the fuel tank filler pipe assembly.


Hide 77701W 4.INSTALL NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.

Connect the No. 1 canister outlet hose sub-assembly to the No. 6 fuel tank breather tube.


b.

Engage the 2 clamps to install the No. 1 canister outlet hose sub-assembly to the fuel tank assembly.


Hide 77028F 5.INSTALL NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY

a.

Engage the 2 clamps to install the No. 2 fuel emission tube sub-assembly to the fuel tank assembly.


Hide 77209F 6.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Engage the 2 clamps to install the fuel tank main tube sub-assembly to the fuel tank assembly.


Hide 77100 7.INSTALL FUEL TANK ASSEMBLY

a.

Clean and degrease the bolt holes.


b.

Using an engine lifter, set the fuel tank assembly.


c.

Install the fuel tank assembly to the vehicle with 4 new bolts.

Torque:
14.3 N*m (146 kgf*cm, 11 ft.*lbf)


d.
A247509C02
1.458,0.323 1.677,0.188 true 0.292,0.615 1.052,0.823 true 0.115,0.521 0.427,0.677 0.313,0.156 10 false *1 1.677,0.063 1.833,0.219 0.156,0.156 10 true *2
*1 Fuel Tank Filler Pipe Sub-assembly
*2 No. 1 Fuel Tank Breather Tube


Connect the fuel tank filler pipe sub-assembly and No. 1 fuel tank breather tube to the No. 3 fuel tank filler pipe support.


e.
A305589

Engage the clamp to install the fuel tank filler pipe flange plate to the No. 3 fuel tank filler pipe support.


f.

Install the fuel tank filler pipe flange plate to the vehicle with the bolt.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)


g.

Engage the 2 clamps to connect the No. 6 fuel tank breather tube.

HINT:
A302966C02
1.563,0.708 1.75,0.469 true 0.385,1.479 0.573,1.24 false 2.802,1.51 2.813,1.188 true 0.885,1.198 1.917,1.75 1.917,1.75 2.427,1.188 true 1.792,0.365 2.104,0.521 0.313,0.156 10 true *1 0.198,1.396 0.51,1.552 0.313,0.156 10 false *a 1.865,1.792 2.177,1.948 0.313,0.156 10 false *b 2.729,1.563 3.031,1.823 0.302,0.26 10 true *a
*1 No. 6 Fuel Tank Breather Tube
*a Clamp
*b Rib


Install the No. 6 fuel tank breather tube so that its 2 ribs are between the 2 clamps as shown in the illustration.



Hide 77209F 8.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A313097C02
2.552,2.604 2.781,2.354 false 2.146,2.594 1.927,2.344 false 0.969,2.542 0.75,2.292 false 1.188,3.792 0.938,3.552 false 2.396,4.396 2.646,4.135 false 2.344,4.51 2.667,4.51 false 2.219,4.104 2.479,3.823 true 1.688,4.167 1.99,3.698 1.99,3.698 1.833,4.156 true 2.813,2.281 3.125,2.438 0.313,0.156 10 false *1 0.573,2.208 0.885,2.365 0.313,0.156 10 false *2 2.708,4.438 3.021,4.594 0.313,0.156 10 false *3 2.677,4.073 2.99,4.229 0.313,0.156 10 false *4 0.75,3.469 1.063,3.625 0.313,0.156 10 false *5 2.01,3.615 2.323,3.771 0.313,0.156 10 false *6 1.75,2.281 2.063,2.438 0.313,0.156 10 false *1 2.521,3.729 2.833,3.885 0.313,0.156 10 false *1
*1 Retainer
*2 Fuel Tube Connector Cover
*3 Fuel Tube Connector
*4 Fuel Pipe
*5 Nylon Tube
*6 O-ring
V100135

Push


Line up the fuel main tube and fuel tube connector, and push them together until a "click" sound is heard. If the fuel main tube is difficult to push into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel main tube and reinsert it.


b.

Engage the lock of the fuel tube connector cover.

NOTICE:
·

Check that there is no damage or foreign matter around the connecting parts of the fuel tube connector and fuel main tube before starting this step.

·

After connecting the fuel tube connector, check that it is securely connected by pulling on it.




Hide 77028F 9.CONNECT NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY

a.

Connect the No. 2 fuel emission tube sub-assembly to the fuel tank to canister tube and slide the hose clip to secure it.


Hide 46420 10.CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

a.

Connect the No. 2 parking brake cable assembly to the vehicle with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 77641A 11.INSTALL NO. 1 FUEL TANK PROTECTOR

a.

Install the No. 1 fuel tank protector to the vehicle with the bolt and clip.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 58156 12.INSTALL FRONT NO. 4 FLOOR HEAT INSULATOR

a.
A300030E01
2.813,1.927 2.969,2.125 0.156,0.198 10 false A 1.333,0.958 1.49,1.156 0.156,0.198 10 false B

Install the front No. 4 floor heat insulator to the vehicle with the 2 nuts.

Torque:
Nut A : 5.4 N*m (55 kgf*cm, 48 in.*lbf)
Nut B : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 17410 13.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Free Length of Compression Spring:
Compression Spring Standard Length Minimum Length
Front Side 42 mm (1.65 in.) 40.5 mm (1.59 in.)
Rear Side 40 mm (1.57 in.) 38.5 mm (1.52 in.)


If the length is not as specified, replace the compression spring.


b.
A171211C01
0.927,1.875 0.927,1.438 false 1.604,1.927 1.604,1.573 false 1.823,0.635 2,0.385 false 2.469,0.99 2.646,0.74 false 0.865,1.885 1.177,2.042 0.313,0.156 10 false *1 1.552,1.927 1.865,2.083 0.313,0.156 10 false *2 2.021,0.281 2.333,0.438 0.313,0.156 10 false *a 2.656,0.646 2.969,0.802 0.313,0.156 10 false *b
*1 Exhaust Manifold Converter Sub-assembly
*2 Exhaust Pipe Gasket
*a Wooden Block
*b Plastic Hammer


Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold converter sub-assembly.

NOTICE:
·

Install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket by dropping it, etc.

·

Do not damage the outer surface of the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket with the front exhaust pipe assembly when connecting it.




c.
A171211C01
0.927,1.875 0.927,1.438 false 1.604,1.927 1.604,1.573 false 1.823,0.635 2,0.385 false 2.469,0.99 2.646,0.74 false 0.865,1.885 1.177,2.042 0.313,0.156 10 false *1 1.552,1.927 1.865,2.083 0.313,0.156 10 false *2 2.021,0.281 2.333,0.438 0.313,0.156 10 false *a 2.656,0.646 2.969,0.802 0.313,0.156 10 false *b
*1 Front Exhaust Pipe Assembly
*2 Exhaust Pipe Gasket
*a Wooden Block
*b Plastic Hammer


Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly.

NOTICE:
·

Install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket by dropping it, etc.

·

Do not damage the outer surface of the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket with the tail exhaust pipe assembly when connecting it.




d.

Connect the 3 exhaust pipe supports to install the front exhaust pipe assembly to the vehicle.


e.
A247549C12
0.323,0.375 0.552,0.594 false 0.521,0.896 0.323,1.104 false 2.115,1.229 1.979,0.927 true 0.146,0.281 0.313,0.448 0.167,0.167 10 false *1 0.146,1.031 0.313,1.198 0.167,0.167 10 false *2 2.042,1.229 2.208,1.396 0.167,0.167 10 false *3 2.771,1.323 2.938,1.49 0.167,0.167 10 false *a
*1 Exhaust Manifold Converter Sub-assembly
*2 Front Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between flanges: 8.5 mm (0.335 in.)


Connect the front exhaust pipe sub-assembly to the exhaust manifold converter sub-assembly with the 2 compression springs and 2 bolts.

Torque:

43 N*m (440 kgf*cm, 32 ft.*lbf)


NOTICE:

After the installation, check that the gaps between the flanges of the exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



f.
A247551C04
2.625,1.104 2.854,0.906 false 2.656,1.281 2.875,1.51 false 1.448,1.323 1.24,1.792 true 2.885,0.813 3.063,0.979 0.177,0.167 10 false *1 2.906,1.438 3.083,1.604 0.177,0.167 10 false *2 1.177,1.802 1.354,1.969 0.177,0.167 10 false *3 0.479,0.583 0.656,0.75 0.177,0.167 10 false *a
*1 Front Exhaust Pipe Assembly
*2 Tail Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between flanges: 6.5 mm (0.256 in.)


Connect the front exhaust pipe assembly to the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:

43 N*m (440 kgf*cm, 32 ft.*lbf)


NOTICE:

After the installation, check that the gaps between the flanges of the tail exhaust pipe assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



g.

Engage the clamp to connect the heated oxygen sensor wire to the wire harness clamp bracket.


h.

Connect the heated oxygen sensor connector.


Hide 51405A 14.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY (w/ Metal Type Under Cover)

Hide 51451A 15.INSTALL CENTER ENGINE UNDER COVER (w/ Metal Type Under Cover)

Hide 57533B 16.INSTALL FRONT FLOOR CENTER BRACE

Hide 17.INSTALL REAR WHEEL LH

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 77020A 18.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 19.ADD FUEL

Hide 77310A 20.INSTALL FUEL TANK CAP ASSEMBLY

Hide 22.INSPECT FOR EXHAUST GAS LEAK

HINT:

Perform "Inspection After Repairs" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>2NR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION