Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY(for TMT Made) › 2017.10–2018.01
RM30M0E _55 Steering _017104 STEERING COLUMN _0333490 STEERING COLUMN ASSEMBLY(for TMT Made) A

STEERING COLUMN  STEERING COLUMN ASSEMBLY(for TMT Made)  DISASSEMBLY  


CAUTION / NOTICE / HINT

HINT:

Refer to Service Bulletin for the installation position of the transponder key ECU assembly.


PROCEDURE

Hide 45209 1.REMOVE STEERING SLIDING YOKE SUB-ASSEMBLY

a.
C232525C05
1.875,0.875 2.51,0.698 2.51,0.698 1.927,0.729 true 2.604,0.604 2.917,0.76 0.313,0.156 10 false *a
*a Matchmark


Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering sliding yoke sub-assembly.


b.

Remove the bolt and the steering sliding yoke sub-assembly from the No. 2 steering intermediate shaft assembly.


Hide 45260 2.REMOVE NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C285110C02
0.896,1.104 1.469,1.146 true 0.927,0.552 1.656,0.75 true 0.708,0.438 1.021,0.594 0.313,0.156 10 false *a 0.667,1.042 0.885,1.198 0.219,0.156 10 false *b
*a Alignment mark
*b Slit


Check that the slit of the No. 2 steering intermediate shaft assembly is aligned with the alignment mark of the steering column assembly.


b.

Remove the bolt and the No. 2 steering intermediate shaft assembly from the steering column assembly.


Hide 69057A 3.REMOVE IGNITION SWITCH LOCK CYLINDER AND KEY SET (w/o Smart Entry and Start System)

a.

Secure the steering column assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using a drill, drill a hole in the steering lock set bolt and insert a screw extractor.


c.
C283342C02
2.115,0.833 1.854,0.677 false 2.167,0.802 2.479,0.958 0.313,0.156 10 false *a
*a Screw Extractor


Using the screw extractor, remove the steering lock set bolt and the ignition switch lock cylinder and key set.


Hide 84052 4.REMOVE UNLOCK WARNING SWITCH ASSEMBLY (w/o Smart Entry and Start System)

a.
C287269

Insert the key.


b.

Disengage the 2 claws and remove the unlock warning switch assembly.

HINT:

Slide the unlock warning switch assembly, in the direction shown by the arrow in the illustration, to remove it.



Hide 85432 5.REMOVE KEY INTERLOCK SOLENOID (for CVT without Smart Entry and Start System)

a.
C287270

Remove the screw.


b.

Disengage the claw to remove the key interlock solenoid from the upper steering column bracket assembly.


Hide 84450 6.REMOVE IGNITION OR STARTER SWITCH ASSEMBLY (w/o Smart Entry and Start System)

a.
C232531

Disengage the 2 claws and remove the ignition or starter switch assembly from the upper steering column bracket assembly.

NOTICE:

Be sure to start operation while the ignition or starter switch assembly faces upward, and while the upper steering column bracket assembly faces downward.



Hide 45020A 7.REMOVE STEERING LOCK ACTUATOR ASSEMBLY (w/ Smart Entry and Start System)

a.

Secure the steering column assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

Using a drill, drill a hole in the steering lock set bolt and insert a screw extractor.


c.
C283342C01
2.115,0.833 1.854,0.677 false 2.167,0.802 2.479,0.958 0.313,0.156 10 false *a
*a Screw Extractor


Using the screw extractor, remove the steering lock set bolt and the steering lock actuator assembly from the steering column assembly.


Hide 80960 8.REMOVE POWER STEERING MOTOR ASSEMBLY

NOTICE:
·

Do not drop the power steering motor assembly, strike it with tools or subject it to impacts.

·

If the power steering motor assembly is subjected to an impact, replace it with a new one.

·

Do not pull the wire harness of the power steering motor assembly.

·

Do not allow any moisture to come into contact with the power steering motor assembly.

·

Do not allow any foreign objects to contaminate the steering column assembly and the power steering motor assembly.

·

Do not loosen any bolts not mentioned in the procedure.



a.
C382977

Cut the clamp and remove the clamp from the steering column assembly.


b.
C382978

Remove the tape and separate the wire harness from the power steering motor assembly.


c.
C382979

Remove the 2 bolts and power steering motor assembly from the steering column assembly.