1.REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
2.DRAIN FUEL
3.REMOVE REAR WHEEL LH
57533B
4.REMOVE FRONT FLOOR CENTER BRACE
17410
5.REMOVE FRONT EXHAUST PIPE ASSEMBLY
Disconnect the heated oxygen sensor connector.
Disengage the clamp to disconnect the heated oxygen sensor wire from the wire harness clamp bracket.
Remove the 2 bolts and 2 compression springs to separate the front exhaust pipe assembly from the exhaust manifold converter sub-assembly.
Remove the 2 bolts and 2 compression springs to separate the front exhaust pipe assembly from the tail exhaust pipe assembly.
Disconnect the 3 exhaust pipe supports to remove the front exhaust pipe assembly from the vehicle.
Remove the 2 exhaust pipe gaskets from the exhaust manifold converter sub-assembly and front exhaust pipe assembly.
58156
6.REMOVE FRONT NO. 4 FLOOR HEAT INSULATOR
Remove the 2 nuts and front No. 4 floor heat insulator from the vehicle.
77641A
7.REMOVE NO. 1 FUEL TANK PROTECTOR
Remove the bolt, clip and No. 1 fuel tank protector from the vehicle.
46420
8.SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY
Remove the 2 bolts to separate the No. 2 parking brake cable assembly from the vehicle.
77028F
9.DISCONNECT NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY
Slide the hose clip and disconnect the No. 2 fuel emission tube sub-assembly from the fuel tank to canister tube.
77209F
10.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
| *1 | Retainer |
| *2 | Fuel Tube Connector Cover |
| *3 | Fuel Tube Connector |
| *4 | Fuel Pipe |
| *5 | Nylon Tube |
| *6 | O-ring |
|
Pull |
|
Pinch |
|
Pull Out |
Release the lock of the fuel tube connector cover as shown in the illustration, then pull out the fuel tank main tube sub-assembly.
If the fuel tube connector and fuel main tube are stuck together, push in and pull out the fuel tube connector while squeezing the fuel main tube to release the connection, and then disconnect the fuel tube connector.
Clean away any dirt or foreign matter from the fuel tube connector before performing the operation.
The fuel tube connector and fuel main tube are sealed by O-ring, so be careful to prevent damage to and foreign matter sticking to the contact surfaces.
Do not use any tools.
After disconnecting the fuel tube connector, check that there is no foreign matter on the seal surface of the fuel main tube.
After disconnecting the fuel tank main tube sub-assembly, protect the contact surfaces by covering them with a plastic bag.
Do not bend or twist the tubes.
77701W
11.DISCONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY
| *1 | No. 6 Fuel Tank Breather Tube |
Disconnect the No. 1 canister outlet hose sub-assembly from the No. 6 fuel tank breather tube.
12.DISCONNECT FUEL TANK BREATHER TUBE SUB-ASSEMBLY
| *1 | Fuel Tank Breather Tube Connector |
Loosen the hose clamp and disconnect the fuel tank breather tube sub-assembly from the fuel tank breather tube connector.
77213B
13.DISCONNECT FUEL TANK TO FILLER PIPE HOSE
Loosen the hose clamp and disconnect the fuel tank to filler pipe hose from the fuel tank assembly.
77100
14.REMOVE FUEL TANK ASSEMBLY
Using an engine lifter, support the fuel tank assembly.
Remove the 4 bolts and fuel tank assembly from the vehicle.
Make sure that the fuel tank assembly does not fall.
77209F
15.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY
Disengage the 2 clamps to remove the fuel tank main tube sub-assembly from the fuel tank assembly.
77028F
16.REMOVE NO. 2 FUEL EMISSION TUBE SUB-ASSEMBLY
Disengage the 2 clamps to remove the No. 2 fuel emission tube sub-assembly from the fuel tank assembly.
77701W
17.REMOVE NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY
Disengage the 2 clamps to remove the No. 1 canister outlet hose sub-assembly from the fuel tank assembly.