Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE FLUID(for RHD) › from 2017.10
RM30M0E _54 Brake _017099 BRAKE SYSTEM (OTHER) _0092762 BRAKE FLUID(for RHD) N

BRAKE SYSTEM (OTHER)  BRAKE FLUID(for RHD)  BLEEDING  


CAUTION / NOTICE / HINT

NOTICE:

If brake fluid leaks onto any painted surface, immediately wash it off.


HINT:

If any work is performed on the brake system or if air in the brake lines is suspected, bleed the air from the brake system.


PROCEDURE

Hide 55784B 1.REMOVE CENTER COWL TOP VENTILATOR LOUVER

Hide 2.FILL RESERVOIR WITH BRAKE FLUID

Hide 47201 3.BLEED BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ ABS)

NOTICE:
·

To prevent brake fluid from damaging painted surfaces, cover any surrounding parts with a piece of cloth.

·

Be sure to clean your hands before bleeding the brake master cylinder sub-assembly to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.



HINT:

If the brake master cylinder sub-assembly is reinstalled or if the reservoir becomes empty, bleed the air from the brake master cylinder sub-assembly.


a.
C282206

Using a 10 mm union nut wrench, disconnect the 2 brake tubes from the brake master cylinder sub-assembly.


b.
C282207

Slowly depress the brake pedal and hold it there.*1


c.
C282208

Cover the 2 outer holes with fingers and release the brake pedal.*2


d.

Repeat Steps *1 and *2, 3 or 4 times.


e.
C388800C01
1.844,3.01 2.156,3.167 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, connect the 2 brake tubes to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 47201 4.BLEED BRAKE MASTER CYLINDER SUB-ASSEMBLY (w/ VSC)

NOTICE:
·

To prevent brake fluid from damaging painted surfaces, cover any surrounding parts with a piece of cloth.

·

Be sure to clean your hands before bleeding the brake master cylinder sub-assembly to avoid any potential contamination of the brake system. Contamination, for example by dirt particles or mineral oil, could lead to functional brake problems.



HINT:

If the brake master cylinder sub-assembly is reinstalled or if the reservoir becomes empty, bleed the air from the brake master cylinder sub-assembly.


a.
C282206

Using a 12 mm union nut wrench, disconnect the 2 brake tubes from the brake master cylinder sub-assembly.


b.
C282207

Slowly depress the brake pedal and hold it there.*1


c.
C282208

Cover the 2 outer holes with fingers and release the brake pedal.*2


d.

Repeat Steps *1 and *2, 3 or 4 times.


e.
C388800C01
1.844,3.01 2.156,3.167 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 12 mm union nut wrench, connect the 2 brake tubes to the brake master cylinder sub-assembly.

Torque:
Specified tightening torque : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




Hide 5.BLEED BRAKE LINE

NOTICE:
·

Bleed the brake line of the wheel farthest from the brake master cylinder sub-assembly first.

·

Add brake fluid to keep the level between the MIN and MAX lines of the reservoir while bleeding the brakes.



a.
C274982

Connect a vinyl tube to the bleeder plug.


b.

Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1


c.

At the point where the fluid stops coming out, tighten the bleeder plug, and then release the brake pedal.*2


d.

Repeat Steps *1 and *2 until all the air in the fluid is completely bled out.


e.

Tighten the bleeder plug.

Torque:
Front brake : 8.3 N*m (85 kgf*cm, 73 in.*lbf)
Rear brake (for drum type) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Rear brake (for disc type) : 11 N*m (112 kgf*cm, 8 ft.*lbf)


f.

Repeat the above procedure to bleed the air out of the brake line for each wheel.


Hide 44510 6.BLEED BRAKE ACTUATOR ASSEMBLY (w/ VSC)

NOTICE:
·

After bleeding the brake system, if the required brake pedal reserve distance cannot be obtained, perform air bleeding of the brake actuator assembly with the GTS by following the procedure below.

·

Perform the procedure for each brake line system until "Air Bleeding is complete" is displayed on the GTS.



a.

Depress the brake pedal more than 20 times with the ignition switch off.


b.

Connect the GTS to the DLC3 and turn the ignition switch to ON.

NOTICE:

Do not start the engine.



c.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility.


d.

Bleed the front right/rear left brake line system.

i.

Enter the menu "Air Bleeding" and bleed the brake actuator assembly following the instructions on the GTS.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Air Bleeding
50005 105 125
Instruction on the GTS Bleeding Portion
Increase Line (1st) All wheels
Increase Line (2nd and later) Front right and rear left wheels
Decrease Line Front right wheel

NOTICE:

Perform air bleeding for the front right/rear left brake line system until "Air Bleeding is complete" is displayed on the GTS.




e.

Bleed the front left/rear right brake line system.

i.

Enter the menu "Air Bleeding" and bleed the brake actuator assembly following the instructions on the GTS.

Chassis > ABS/VSC/TRC > Utility
Tester Display
Air Bleeding
50005 105 125
Instruction on the GTS Bleeding Portion
Increase Line (1st) All wheels
Increase Line (2nd and later) Front left and rear right wheels
Decrease Line Front left wheel

NOTICE:

Perform air bleeding for the front left/rear right brake line system until "Air Bleeding is complete" is displayed on the GTS.




f.

Perform the Bleed Brake Line procedure again.

NOTICE:

Perform air bleeding for the brake line of each wheel to bleed the brake system completely.



g.

After air bleeding, tighten each bleeder plug.

Torque:
Front brake : 8.3 N*m (85 kgf*cm, 73 in.*lbf)
Rear brake (for drum type) : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
Rear brake (for disc type) : 11 N*m (112 kgf*cm, 8 ft.*lbf)


h.

Turn the GTS off and disconnect the GTS from the DLC3.


i.

Turn the ignition switch off.


Hide 7.INSPECT FOR BRAKE FLUID LEAK

Hide 8.INSPECT BRAKE FLUID LEVEL IN RESERVOIR

Hide 55784B 9.INSTALL CENTER COWL TOP VENTILATOR LOUVER