Home › Drivetrain › C50 MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE UNIT(for 2NR-FE) › from 2017.10
RM30M0E _52 Drivetrain _017090 C50 MANUAL TRANSMISSION / TRANSAXLE _0266928 MANUAL TRANSAXLE UNIT(for 2NR-FE) A

C50 MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT(for 2NR-FE)  REASSEMBLY  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

All disassembled parts should be cleaned before reassembly.

·

Coat all of the sliding and rotating surfaces with gear oil before reassembly, and check that they move smoothly after reassembly.



Hide 33134B 2.INSTALL OUTPUT SHAFT COVER

a.
C282954C01
1.458,0.094 1.771,0.292 0.313,0.198 10 false *1 2.552,0.094 2.865,0.292 0.313,0.198 10 false *2
*1 Transaxle Case
*2 Output Shaft Cover


Install the output shaft cover to the transaxle case.

NOTICE:

Insert the output shaft cover key into the case groove.



Hide 33321N 3.INSTALL OUTPUT SHAFT FRONT BEARING

a.

Coat a new output shaft front bearing with gear oil.


b.
C282955E01
2.406,0.979 2.271,0.51 2.271,0.51 2.5,0.51 false 1.177,1.01 0.781,0.521 0.781,0.521 1.208,0.563 true 0.469,0.427 0.927,0.625 0.458,0.198 10 false SST 1.958,0.438 2.417,0.635 0.458,0.198 10 false SST

Using SST and a press, install the output shaft front bearing to the transaxle case.

SST
09950-60010  (09951-00550)
09950-70010  (09951-07150)

NOTICE:
·

Install the output shaft front bearing in the correct direction as shown in the illustration.


·

Press in the output shaft front bearing until it is fit against the end.




Hide 31105D 4.INSTALL FRONT TRANSAXLE CASE OIL SEAL

a.
C282956C01
1.156,1.5 0.719,0.604 0.719,0.604 1.208,0.75 true 2.552,0.719 2.448,0.365 2.448,0.365 2.625,0.427 true 0.406,0.5 0.865,0.698 0.458,0.198 10 false SST 2.146,0.271 2.604,0.469 0.458,0.198 10 false SST 2.115,0.917 2.427,1.115 0.313,0.198 10 false *a
*a Drive in Depth


Using SST and a hammer, install a new front transaxle case oil seal to the transaxle case.

SST
09950-60010  (09951-00370)
09950-70010  (09951-07150)

Standard depth:

15.6 to 16.0 mm (0.615 to 0.629 in.)



b.

Coat the lip of the front transaxle case oil seal with MP grease.


Hide 33311A 5.INSTALL INPUT SHAFT FRONT BEARING

a.

Coat a new input shaft front bearing with gear oil.


b.
C282957C01
0.833,0.875 0.625,0.375 0.625,0.375 0.854,0.479 true 2.521,0.292 2.708,0.229 2.708,0.229 2.646,0.417 false 2.76,0.135 3.219,0.333 0.458,0.198 10 false SST 0.313,0.292 0.771,0.49 0.458,0.198 10 false SST 3.073,0.729 3.385,0.927 0.313,0.198 10 false *a
*a Drive in Depth


Using SST and a press, install the input shaft front bearing to the transaxle case.

SST
09950-60010  (09951-00420)
09950-70010  (09951-07150)

Standard depth:

0 to 0.3 mm (0 to 0.0118 in.)



Hide 41311E 6.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C282958E01
1.854,0.51 2.177,0.396 2.177,0.396 1.885,0.604 false 2.229,0.313 2.688,0.51 0.458,0.198 10 false SST

Using SST and a press, install a new front differential case front tapered roller bearing (inner race) to the differential case assembly.

SST
09350-32014  (09351-32120)
09950-60010  (09951-00530)


b.

Apply gear oil to the inside of a new front differential case front tapered roller bearing (outer race).


c.
C282959E01
1.823,0.74 2.198,0.74 2.198,0.74 1.927,1.01 false 2.24,0.635 2.698,0.833 0.458,0.198 10 false SST

Using SST and a press, install the front differential case front tapered roller bearing (outer race) with the front differential case front plate washer to the transaxle case.

SST
09950-60020  (09951-00680)
09950-70010  (09951-07150)


Hide 41311F 7.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C282960E01
1.969,0.583 2.281,0.385 2.281,0.385 1.938,0.479 false 2.313,0.281 2.771,0.479 0.458,0.198 10 false SST

Using SST and a press, install a new front differential case rear tapered roller bearing (inner race) to the differential case assembly.

SST
09350-32014  (09351-32120)
09950-60010  (09951-00530)


b.

Apply gear oil to the inside of a new front differential case rear tapered roller bearing (outer race).


c.
C295271C01
2.042,1.5 2.802,0.5 2.802,0.5 2.115,0.875 true 2,0.531 2.813,0.5 false 2.865,0.427 3.323,0.625 0.458,0.198 10 false SST

Using SST and a press, install the front differential case rear tapered roller bearing (outer race) with the front differential case rear plate washer to the manual transmission case.

SST
09309-36010  
09950-60020  (09951-00710)
09950-70010  (09951-07150)

HINT:

Use a front differential case rear plate washer of the same thickness as the removed one.



Hide 8.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.
C282932

Coat the differential case assembly with gear oil and install it to the transaxle case.


b.

Install the manual transmission case with the 16 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


c.
C282962E01
0.979,1.313 1.615,0.323 true 1.656,0.229 2.115,0.427 0.458,0.198 10 false SST

Using SST and a torque wrench, turn the differential case assembly to the right and left 2 or 3 times to allow the bearings to settle.

SST
09564-32011  


d.
C282962E01
0.979,1.313 1.615,0.323 true 1.656,0.229 2.115,0.427 0.458,0.198 10 false SST

Using SST and a torque wrench, measure the preload.

SST
09564-32011  

Preload (at starting):
New bearing:

0.78 to 1.57 N*m (8.0 to 16.0 kgf*cm, 7.0 to 13.8 in.*lbf)

Used bearing:

0.49 to 0.98 N*m (5.0 to 9.9 kgf*cm, 4.4 to 8.6 in.*lbf)


If the preload is out of the specification, select another front differential case rear plate washer.

Front Differential Case Rear Plate Washer Thickness:
Part No. Mark Thickness
mm (in.)
Part No. Mark Thickness
mm (in.)
90564-41014 AA 2.10 (0.0827) 90564-41024 LL 2.60 (0.1024)
90564-41015 BB 2.15 (0.0846) 90564-41025 MM 2.65 (0.1043)
90564-41016 CC 2.20 (0.0866) 90564-41026 NN 2.70 (0.1063)
90564-41017 DD 2.25 (0.0886) 90564-41027 PP 2.75 (0.1083)
90564-41018 EE 2.30 (0.0906) 90564-41028 QQ 2.80 (0.1102)
90564-41019 FF 2.35 (0.0925) 90564-41029 RR 2.85 (0.1122)
90564-41020 GG 2.40 (0.0945) 90564-41030 SS 2.90 (0.1142)
90564-41021 HH 2.45 (0.0965) 90564-41031 TT 2.95 (0.1161)
90564-41022 JJ 2.50 (0.0984) 90564-41032 UU 3.00 (0.1181)
90564-41023 KK 2.55 (0.1004) - - -


HINT:

The preload changes by approximately 0.3 to 0.4 N*m (3.1 to 4.0 kgf*cm, 2.7 to 3.5 in.*lbf) per each 0.05 mm (0.00197 in.) change in the plate washer thickness.



e.

Remove the 16 bolts and manual transmission case.


f.

Remove the differential case assembly from the transaxle case.


Hide 43420H 9.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.
C288393C01
1.917,0.333 2.25,0.333 false 1.167,0.917 1.344,0.917 false 0.188,1.135 0.5,1.333 0.313,0.198 10 false *a 0.854,0.833 1.313,1.031 0.458,0.198 10 false SST 1.583,0.25 2.042,0.448 0.458,0.198 10 false SST
*a Drive in Depth


Using SST and a hammer, install a new front drive shaft oil seal LH to the manual transmission case.

SST
09316-60011  (09316-00011)

Standard depth:

9.4 to 10.4 mm (0.371 to 0.409 in.)



b.

Coat the lip of the front drive shaft oil seal LH with MP grease.


Hide 43410M 10.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.
C288394C01
2.24,1.031 2.042,0.615 2.042,0.615 2.292,0.604 true 0.938,1.094 0.792,0.635 0.792,0.635 1.031,0.625 true 0.208,1.177 0.521,1.375 0.313,0.198 10 false *a 1.75,0.552 2.208,0.75 0.458,0.198 10 false SST 0.479,0.583 0.938,0.781 0.458,0.198 10 false SST
*a Drive in Depth


Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle case.

SST
09710-20011  (09710-06071)
09950-70010  (09951-07150)

Standard depth:

11.4 to 12 mm (0.449 to 0.472 in.)



b.

Coat the lip of the front drive shaft oil seal RH with MP grease.


Hide 33449 11.INSTALL TRANSMISSION MAGNET

a.
C282939

Clean the transmission magnet and install it to the transaxle case.


Hide 33326 12.INSTALL BEARING LOCK PLATE

a.
C282938

Install the bearing lock plate to the transaxle case with the bolt.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 33124D 13.INSTALL NO. 2 OIL RECEIVER PIPE

a.
C282965

Install the No. 2 oil receiver pipe to the manual transmission case with the bolt.

Torque:
17.2 N*m (175 kgf*cm, 13 ft.*lbf)

NOTICE:
·

Do not deform the No. 2 oil receiver pipe.

·

Install the No. 2 oil receiver pipe while holding it against the manual transmission case as shown in the illustration.




Hide 33124C 14.INSTALL NO. 1 OIL RECEIVER PIPE

a.
C282964

Install the No. 1 oil receiver pipe to the manual transmission case with the bolt.

Torque:
17.2 N*m (175 kgf*cm, 13 ft.*lbf)

NOTICE:
·

Do not deform the No. 1 oil receiver pipe.

·

Install the No. 1 oil receiver pipe while holding it against the manual transmission case as shown in the illustration.




Hide 33280 15.INSTALL REVERSE RESTRICT PIN ASSEMBLY

a.
C282966

Install the reverse restrict pin assembly to the manual transmission case.

NOTICE:

Set the reverse restrict pin assembly in the correct direction.



b.
C282967C01
0.625,1.292 0.938,1.49 0.313,0.198 10 false *a
*a Drive in Depth


Using a 5 mm pin punch and a hammer, install the reverse restrict pin slotted spring pin to the reverse restrict pin assembly.

Standard depth:

15.5 to 16.5 mm (0.611 to 0.649 in.)



c.
C294737

Clean and degrease the reverse restrict pin plug and installation hole.


d.

Apply adhesive to 2 or 3 threads on the end of the reverse restrict pin plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



e.

Using a 6 mm hexagon socket wrench, install the reverse restrict pin plug to the manual transmission case.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 33125 16.INSTALL MANUAL TRANSAXLE CASE RECEIVER

a.
C282933

Install the manual transaxle case receiver to the transaxle case with the bolt.

Torque:
11.3 N*m (115 kgf*cm, 8 ft.*lbf)


Hide 17.INSTALL DIFFERENTIAL CASE ASSEMBLY

a.
C282932

Coat the differential case assembly with gear oil and install it to the transaxle case.


Hide 18.INSTALL INPUT SHAFT ASSEMBLY

a.
C288395C01
0,0 3.427,3.427 3.427,3.427
V100145

Gear Oil


Apply gear oil to the entire circumference of the input shaft assembly.

NOTICE:

To prevent the front transaxle case oil seal from being caught, make sure to apply gear oil to the input shaft assembly.



b.
C282931

Coat the sliding and rotating surfaces of the input shaft assembly and output shaft assembly with gear oil and install them to the transaxle case.

NOTICE:

Do not damage the front transaxle case oil seal.



Hide 33402 19.INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY

a.
C296759C01
1.073,0.802 1.781,0.688 true 2.188,1.729 2.406,1.969 true 0.896,0.719 1.208,0.875 0.313,0.156 10 true *a 2.458,1.938 2.771,2.094 0.313,0.156 10 true *b
*a Alignment Mark
*b Bolt Hole


Coat the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft with gear oil, and install them as shown in the illustration.

HINT:

Align the alignment mark on the reverse idler gear shaft with the bolt hole shown in the illustration.



Hide 33212A 20.INSTALL NO. 1 GEAR SHIFT FORK SHAFT

a.
C282970C01
1.958,1.448 2.896,0.677 true 2.229,0.552 2.594,0.271 false 2.604,0.156 2.917,0.354 0.313,0.198 10 false *2 2.927,0.583 3.24,0.781 0.313,0.198 10 false *1
*1 No. 1 Gear Shift Fork
*2 No. 2 Gear Shift Fork


Coat the No. 1 gear shift fork and No. 2 gear shift fork with gear oil and install them.


b.
C296760C01
1.938,1.021 2.677,0.698 true 2.74,0.625 3.052,0.823 0.313,0.198 10 false *1
*1 No. 1 Gear Shift Fork Shaft


Coat the No. 1 gear shift fork shaft with gear oil and install it.


c.

Clean and degrease the No. 1 gear shift fork set bolt and installation hole.


d.

Apply adhesive to 2 or 3 threads on the end of the No. 1 gear shift fork set bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



e.

Install the No. 1 gear shift fork set bolt.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)


f.
C282972

Using a brass bar and a hammer, install a new shift fork shaft snap ring to the No. 1 gear shift fork shaft.


Hide 33244G 21.INSTALL NO. 3 GEAR SHIFT FORK SHAFT

a.
C296761

Coat the 2 reverse shift fork balls with MP grease and install them to the reverse shift fork.


b.

Install the reverse shift fork to the No. 3 gear shift fork shaft.


c.
C282974

Secure the No. 3 gear shift fork shaft in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



d.

Using a brass bar and a hammer, install 2 new shift fork shaft snap rings to the No. 3 gear shift fork shaft.


e.
C282975

Coat the No. 3 gear shift fork shaft with gear oil and install it.


Hide 33243A 22.INSTALL NO. 2 GEAR SHIFT FORK SHAFT

a.
C117123

Coat the No. 1 gear shift head and No. 2 gear shift fork shaft with gear oil and install them.

NOTICE:

To avoid interference by the 2 reverse shift fork balls, lift up the No. 3 gear shift fork shaft to the position shown in the illustration.



b.
C282922

Clean and degrease the No. 2 gear shift fork set bolt, No. 1 gear shift head set bolt and installation holes.


c.

Apply adhesive to 2 or 3 threads on the ends of the No. 2 gear shift fork set bolt and No. 1 gear shift head set bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



d.

Install the No. 2 gear shift fork set bolt and No. 1 gear shift head set bolt to the No. 2 gear shift fork and No. 1 gear shift head.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 33240 23.INSTALL REVERSE SHIFT ARM BRACKET ASSEMBLY

a.
C296757

Install the reverse shift arm bracket assembly to the transaxle case with the 2 bolts.

Torque:
17.2 N*m (175 kgf*cm, 13 ft.*lbf)


Hide 33111 24.INSTALL MANUAL TRANSMISSION CASE

a.

Clean and degrease the contact surfaces of the manual transmission case and transaxle case.


b.
C296750C01
0.813,1.781 1.125,1.49 true 0.604,1.698 0.917,1.896 0.313,0.198 10 false *a
*a Seal Packing
(Seal Diameter: 1.2 mm (0.0472 in.))


Apply seal packing to the manual transmission case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.



c.

Install the manual transmission case to the transaxle case.


d.
C294665C01
0.396,0.948 0.802,0.927 true 0.188,0.875 0.5,1.031 0.313,0.156 10 false *1
*1 Clutch Tube Bracket


Install the clutch tube bracket and 13 bolts to the manual transmission case.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


e.
C294929

Install the 3 bolts to the transaxle case.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 33451H 25.INSTALL REVERSE IDLER GEAR SHAFT BOLT

a.
C282911

Clean and degrease the reverse idler gear shaft bolt and installation hole.


b.

Apply adhesive to 2 or 3 threads on the end of the reverse idler gear shaft bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.

Install a new gasket and reverse idler gear shaft bolt to the manual transmission case.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 33290 26.INSTALL NO. 1 LOCK BALL ASSEMBLY

a.
C282917

Clean and degrease the No. 1 lock ball assembly and installation hole.


b.

Apply adhesive to 2 or 3 threads on the end of the No. 1 lock ball assembly.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.

Using a 6 mm hexagon socket wrench, install the No. 1 lock ball assembly to the manual transmission case.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 33275C 27.INSTALL SHIFT DETENT BALL

a.
C293379C01
1.167,0.708 1.625,0.917 true 0.99,0.604 1.167,0.781 0.177,0.177 10 true *a
*a No. 1 Gear Shift Fork Shaft Hole


Install the 2 shift detent balls, 2 compression springs and 2 spring seats to the manual transmission case.

NOTICE:

Do not drop the shift detent ball into the No. 1 gear shift fork shaft hole of the manual transmission case.



b.
C296762

Clean and degrease the 2 shift detent ball plugs and installation holes.


c.

Apply adhesive to 2 or 3 threads on the ends of the 2 shift detent ball plugs.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



d.

Using a 6 mm hexagon socket wrench, install the 2 shift detent ball plugs to the manual transmission case.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


e.
C282977

Install the shift detent ball, compression spring and spring seat to the transaxle case.


f.
C282915

Clean and degrease the shift detent ball plug and installation hole.


g.

Apply adhesive to 2 or 3 threads on the end of the shift detent ball plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



h.

Using a 6 mm hexagon socket wrench, install the shift detent ball plug to the transaxle case.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 33311X 28.INSTALL INPUT SHAFT REAR BEARING HOLE SNAP RING

a.
C282910

Using a snap ring expander, install a new input shaft rear bearing hole snap ring to the input shaft.

NOTICE:

Do not expand the input shaft rear bearing hole snap ring excessively.



Hide 33111R 29.INSTALL OUTPUT SHAFT REAR BEARING HOLE SNAP RING

a.
C282909

Using a snap ring expander, install a new output shaft rear bearing hole snap ring to the output shaft.

NOTICE:

Do not expand the output shaft rear bearing hole snap ring excessively.



Hide 33242E 30.INSTALL SHIFT FORK SHAFT SNAP RING

a.
C282978

Using a brass bar and a hammer, install a new shift fork shaft snap ring to the No. 2 gear shift fork shaft.


Hide 33151D 31.INSTALL REAR BEARING RETAINER

a.
C296753

Clean and degrease the 5 bolts and installation holes.


b.

Apply adhesive to 2 or 3 threads on the ends of the 5 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.

Install the rear bearing retainer to the manual transmission case with the 5 bolts.

Torque:
27.4 N*m (279 kgf*cm, 20 ft.*lbf)


Hide 33428C 32.INSTALL 5TH DRIVEN GEAR

a.
C287909C01
0.844,1.208 1.073,1.208 false 1.719,0.938 1.958,0.979 false 1.104,1.125 1.563,1.323 0.458,0.198 10 false SST 1.448,0.865 1.906,1.063 0.458,0.198 10 false SST 1.698,0.573 2.156,0.771 0.458,0.198 10 false *a 2.583,0.583 3.042,0.781 0.458,0.198 10 false *b
*a Hold
*b Turn


Using SST, install the 5th driven gear to the output shaft.

SST
09309-12020  


Hide 33336A 33.INSTALL 5TH GEAR NEEDLE ROLLER BEARING

C296763C01
0.667,0.646 1.25,0.969 true 1.146,1.74 1.323,1.198 true 0.479,0.563 0.792,0.719 0.313,0.156 10 false *1 1.063,1.771 1.271,2 0.208,0.229 10 true *2
*1 5th Gear Needle Roller Bearing
*2 5th Gear Bearing Spacer


a.

Coat the 5th gear needle roller bearing and 5th gear bearing spacer with gear oil, and install them to the input shaft.


Hide 33336 34.INSTALL 5TH GEAR

a.
C282980

Coat the 5th gear with gear oil and install it to the input shaft.


Hide 33369 35.INSTALL NO. 3 SYNCHRONIZER RING

a.
C282981

Coat the No. 3 synchronizer ring with gear oil and install it to the 5th gear.


Hide 33393 36.INSTALL NO. 3 TRANSMISSION CLUTCH HUB

a.
C297448C01
1.677,1.823 2.229,1.802 true 1.479,1.729 1.792,1.927 0.313,0.198 10 false *a
*a Wooden Block


Place a suitable sized wooden block to support the input shaft.


b.
C282982C01
1.646,2.719 1.958,2.917 0.313,0.198 10 false *a
*a Engine Side


Install the 3 synchromesh shifting keys and 2 synchromesh shifting key springs to the No. 3 transmission clutch hub as shown in the illustration.

NOTICE:

Do not set the 2 shifting key spring openings in the same position.



c.
C297447C01
0.469,2.219 1.323,2.167 true 2.021,1.146 2.333,0.875 true 0.24,2.146 0.552,2.302 0.313,0.156 10 false *1 2.74,2.417 3.052,2.573 0.313,0.156 10 false *a 0.688,1.042 1,1.198 0.313,0.156 10 false *b 2.417,0.781 2.729,0.938 0.313,0.156 10 false SST
*1 5th Gear
*a Key Groove Position
*b Engine Side


Using SST and a hammer, install the No. 3 transmission clutch hub to the input shaft.

SST
09636-20010  

NOTICE:
·

Do not install the No. 3 transmission clutch hub in the wrong direction.

·

Install the No. 3 transmission clutch hub with the No. 3 synchronizer ring key groove and No. 3 synchromesh shifting key aligned.

·

Check that the 5th gear is rotating.




d.
C297446

Select a snap ring that will allow minimum axial play.

Standard clearance:

0.1 mm (0.00394 in.) or less


Snap Ring Thickness:
Part No. Mark Thickness
mm (in.)
90520-18002 A 2.25 (0.0886)
90520-18003 B 2.31 (0.0909)
90520-18004 C 2.37 (0.0933)
90520-18006 D 2.43 (0.0957)
90520-18007 E 2.49 (0.0980)
90520-18008 F 2.55 (0.1004)
90520-18009 G 2.61 (0.1028)



e.
C297455

Using a brass bar and a hammer, install a new snap ring to the input shaft.


Hide 37.INSPECT 5TH GEAR THRUST CLEARANCE

a.
C282901

Using a dial indicator, measure the 5th gear thrust clearance.

Standard clearance:

0.10 to 0.55 mm (0.00394 to 0.0216 in.)


Maximum clearance:

0.55 mm (0.0216 in.)


If the clearance exceeds the maximum, replace the No. 3 transmission clutch hub, 5th gear or input shaft rear radial ball bearing.


Hide 38.INSPECT 5TH GEAR RADIAL CLEARANCE

a.
C282902

Using a dial indicator, measure the 5th gear radial clearance.

Standard clearance:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 5th gear, 5th gear needle roller bearing or input shaft.


Hide 33214G 39.INSTALL NO. 3 GEAR SHIFT FORK

a.
C282984

Coat the No. 3 transmission hub sleeve with gear oil and install it with the No. 3 gear shift fork to the No. 3 transmission clutch hub.

HINT:

Set the No. 3 transmission clutch hub in the correct direction.



b.
C282899

Clean and degrease the No. 3 gear shift fork set bolt and installation hole.


c.

Apply adhesive to 2 or 3 threads on the end of the No. 3 gear shift fork set bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



d.

Install the No. 3 gear shift fork set bolt to the No. 3 gear shift fork.

Torque:
15.7 N*m (160 kgf*cm, 12 ft.*lbf)


Hide 33321G 40.INSTALL MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT

a.
C282986

Engage the 2 gears simultaneously to lock the transmission.


b.

Using a 27 mm socket wrench, install a new manual transmission output shaft rear set nut.

Torque:
117.6 N*m (1199 kgf*cm, 87 ft.*lbf)


c.
C282987

Using a chisel and a hammer, stake the manual transmission output shaft rear set nut.


d.

Disengage the 2 gears.


Hide 33102 41.INSTALL MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY

a.

Clean and degrease the contact surfaces of the manual transmission case cover sub-assembly and manual transmission case.


b.
C294738C01
2.083,1.49 2.5,1.719 true 2.552,1.646 2.865,1.844 0.313,0.198 10 false *a
*a Seal Packing
(Seal Diameter 1.2 mm (0.0742 in.)


Apply seal packing to the manual transmission case cover sub-assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:

Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.



c.
C295381

Clean and degrease the 9 bolts and installation holes.


d.

Apply adhesive to 2 or 3 threads on the ends of the 9 bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



e.

Install the manual transmission case cover sub-assembly to the manual transmission case with the 9 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 42.INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY

a.
C295144C01
0.75,0.375 0.906,0.573 0.156,0.198 10 false A 0.781,1.563 0.938,1.76 0.156,0.198 10 true A

Clean and degrease the 2 bolts A and installation holes.


b.

Coat the shift and select lever shaft assembly with gear oil.


c.

Apply adhesive to 2 or 3 threads on the ends of the 2 bolts A.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



d.

Install a new gasket and the shift and select lever shaft assembly to the manual transmission case with the 4 bolts.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)

NOTICE:

Set the claws of the shift interlock plate into the shift head part of the gear shift fork shaft securely.



Hide 33290B 43.INSTALL NO. 2 LOCK BALL ASSEMBLY

a.
C381204

Clean and degrease the No. 2 lock ball assembly and installation hole.


b.

Apply adhesive to 2 or 3 threads on the ends of the No. 2 lock ball assembly.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.

Install the No. 2 lock ball assembly to the manual transmission case.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 33295A 44.INSTALL REVERSE RESTRICT SHAFT

a.
C295142

Clean and degrease the reverse restrict shaft and installation hole.


b.

Apply adhesive to 2 or 3 threads on the end of the reverse restrict shaft.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


NOTICE:

To prevent contamination by foreign matter, install immediately after applying adhesive.



c.

Install the washer and reverse restrict shaft to the manual transmission case.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 33544C 45.INSTALL SHIFT LEVER DAMPER

a.
C295140

Install the shift lever damper to the shift and select lever shaft assembly with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 33590F 46.INSTALL FLOOR SHIFT SELECTING BELL CRANK ASSEMBLY

a.
C295139C01
0.219,1.302 1.167,0.875 true 1.49,1.813 1.844,0.885 true 0.031,1.24 0.344,1.396 0.313,0.156 10 false *1 1.396,1.833 1.708,1.99 0.313,0.156 10 false *2
*1 Floor Shift Selecting Bellcrank Assembly
*2 Control Bellcrank Dust Cover


Coat the inside circumferential surface of the control bellcrank dust cover with MP grease and install it to the floor shift selecting bellcrank assembly.


b.

Install the floor shift selecting bellcrank assembly with control bellcrank dust cover to the manual transmission case with the 2 bolts.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 33111G 47.INSTALL MANUAL TRANSMISSION BREATHER PLUG

a.
C291381N01
0.792,1.021 1.365,1.396 true 0.49,0.917 0.948,1.115 0.458,0.198 10 false SST

Using SST and a hammer, install the manual transmission breather plug to the manual transmission case.

SST
09350-30020  (09350-07110)


Hide 84210 48.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

a.
C295252

Using a 27 mm socket wrench, install a new gasket and back-up light switch assembly to the manual transmission case.

Torque:
40.2 N*m (410 kgf*cm, 30 ft.*lbf)


Hide 33104 49.INSTALL DRAIN PLUG SUB-ASSEMBLY

a.
C283061

Install a new gasket and drain plug sub-assembly to the manual transmission case.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 33101A 50.INSTALL MANUAL TRANSMISSION FILLER PLUG

a.
C283060

Install a new gasket and manual transmission filler plug to the manual transmission case.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 33823 51.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

C295135

a.

Install the No. 1 transmission control cable bracket to the manual transmission case with the 3 bolts.

Torque:
18.4 N*m (188 kgf*cm, 14 ft.*lbf)


Hide 31236B 52.INSTALL RELEASE FORK SUPPORT

Hide 31126 53.INSTALL CLUTCH RELEASE FORK BOOT

Hide 31232A 54.INSTALL RELEASE BEARING HUB CLIP

Hide 31204 55.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 31230 56.INSTALL CLUTCH RELEASE BEARING ASSEMBLY