Home › Drivetrain › C50 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT › from 2017.10
RM30M0E _52 Drivetrain _017090 C50 MANUAL TRANSMISSION / TRANSAXLE _0091175 OUTPUT SHAFT A

C50 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT 1ST GEAR THRUST CLEARANCE

a.
C283017

Using a feeler gauge, measure the 1st gear thrust clearance.

Standard clearance:

0.10 to 0.40 mm (0.00394 to 0.0157 in.)


Maximum clearance:

0.40 mm (0.0157 in.)


If the clearance exceeds the maximum, replace the 1st gear thrust washer, 1st gear or No. 1 transmission clutch hub.


Hide 2.INSPECT 2ND GEAR THRUST CLEARANCE

a.
C283018

Using a dial indicator, measure the 2nd gear thrust clearance.

Standard clearance:

0.10 to 0.55 mm (0.00394 to 0.0216 in.)


Maximum clearance:

0.55 mm (0.0216 in.)


If the clearance exceeds the maximum, replace the No. 1 transmission clutch hub, 2nd gear or 3rd driven gear.


Hide 3.INSPECT 1ST GEAR RADIAL CLEARANCE

a.
C283019

Using a dial indicator, measure the 1st gear radial clearance.

Standard clearance:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 1st gear, 1st gear needle roller bearing or output shaft.


Hide 4.INSPECT 2ND GEAR RADIAL CLEARANCE

a.
C283020

Using a dial indicator, measure the 2nd gear radial clearance.

Standard clearance:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 2nd gear, 2nd gear needle roller bearing or output shaft.


Hide 33422B 5.REMOVE 4TH DRIVEN GEAR

a.
C283021N01
0.5,0.542 0.729,0.688 false 2,0.385 2.458,0.677 true 0.229,0.458 0.688,0.656 0.458,0.198 10 false SST 1.729,0.302 2.188,0.5 0.458,0.198 10 false SST

Using SST and a press, remove the output shaft rear bearing and the 4th driven gear from the output shaft.

SST
09950-00020  


Hide 33431C 6.REMOVE OUTPUT GEAR SPACER

a.
C283022

Remove the output gear spacer from the output shaft.


Hide 33332 7.REMOVE 2ND GEAR

a.
C283023N01
0.563,0.625 0.802,0.771 false 2.052,0.719 2.469,1.031 true 0.292,0.542 0.75,0.74 0.458,0.198 10 false SST 1.781,0.646 2.24,0.844 0.458,0.198 10 false SST

Using SST and a press, remove the 2nd gear and the 3rd driven gear from the output shaft.

SST
09950-00020  


Hide 33332B 8.REMOVE 2ND GEAR NEEDLE ROLLER BEARING

a.
C283024

Remove the 2nd gear needle roller bearing and the 2nd gear bearing spacer from the output shaft.


Hide 33038E 9.REMOVE NO. 2 SYNCHRONIZER RING SET (FOR 2ND GEAR)

a.
C293467C02
0.479,0.51 0.813,0.51 false 0.458,1.021 0.792,1.021 false 0.385,1.583 0.719,1.583 false 0.313,0.438 0.625,0.594 0.313,0.156 10 false *1 0.292,0.948 0.604,1.104 0.313,0.156 10 false *2 0.208,1.51 0.521,1.667 0.313,0.156 10 false *3
*1 Inner Ring
*2 Middle Ring
*3 Outer Ring


Remove the No. 2 synchronizer ring set (for 2nd gear) from the output shaft.


Hide 33335 10.REMOVE 1ST GEAR

a.
C283025

Using 2 screwdrivers and a hammer, remove the No. 1 clutch hub shaft snap ring from the output shaft.

HINT:

Use a piece of cloth to keep the No. 1 clutch hub shaft snap ring from flying off.



b.
C283026N01
0.521,0.583 0.74,0.729 false 1.979,0.521 2.385,0.813 true 0.25,0.5 0.708,0.698 0.458,0.198 10 false SST 1.708,0.438 2.167,0.635 0.458,0.198 10 false SST

Using SST and a press, remove the No. 1 transmission clutch hub and the 1st gear from the output shaft.

SST
09950-00020  

NOTICE:
·

Do not tighten SST excessively.

·

Support the output shaft by hand to prevent it from falling off.




Hide 33037B 11.REMOVE NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR)

a.
C293468C02
0.354,0.49 0.688,0.49 false 0.448,1.135 0.781,1.135 false 0.469,1.656 0.802,1.656 false 0.198,0.417 0.51,0.573 0.313,0.156 10 false *1 0.281,1.063 0.594,1.219 0.313,0.156 10 false *2 0.292,1.583 0.604,1.74 0.313,0.156 10 false *3
*1 Outer Ring
*2 Middle Ring
*3 Inner Ring


Remove the No. 1 synchronizer ring set (for 1st gear) from the 1st gear.


Hide 33335C 12.REMOVE 1ST GEAR NEEDLE ROLLER BEARING

a.
C283027

Remove the 1st gear needle roller bearing from the output shaft.


Hide 33348 13.REMOVE 1ST GEAR THRUST WASHER

a.
C283028

Remove the 1st gear thrust washer from the output shaft.


Hide 33348A 14.REMOVE 1ST GEAR THRUST WASHER PIN OR BALL

a.
C283029

Using a magnet hand, remove the 1st gear thrust washer pin or ball from the output shaft.


Hide 33331 15.REMOVE REVERSE GEAR

a.
C283030

Remove the reverse gear, 3 synchromesh shifting keys and the 3 synchromesh shifting key springs from the No. 1 transmission clutch hub.

NOTICE:

Use a piece of cloth to keep the synchromesh shifting keys and the synchromesh shifting key springs from flying off.