Home › Drivetrain › C50 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT › from 2017.10
RM30M0E _52 Drivetrain _017090 C50 MANUAL TRANSMISSION / TRANSAXLE _0091175 OUTPUT SHAFT A

C50 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  REASSEMBLY  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

All disassembled parts should be cleaned before reassembly.

·

Coat all of the sliding and rotating surfaces with gear oil before reassembly, and check that they move smoothly after reassembly.



Hide 33331 2.INSTALL REVERSE GEAR

a.
C293473

Coat the reverse gear and the No. 1 transmission clutch hub with gear oil.


b.

Install the 3 synchromesh shifting key springs and the 3 synchromesh shifting keys to the No. 1 transmission clutch hub.


c.
C157310

Install the reverse gear to the No. 1 transmission clutch hub.

NOTICE:

Position the reverse gear and the No. 1 transmission clutch hub correctly as shown in the illustration.



Hide 33348A 3.INSTALL 1ST GEAR THRUST WASHER PIN OR BALL

a.
C283029

Coat the 1st gear thrust washer pin or ball with MP grease and install it to the output shaft.


Hide 33348 4.INSTALL 1ST GEAR THRUST WASHER

a.
C283028

Coat the 1st gear thrust washer with gear oil and install it to the output shaft.

HINT:

Fit the 1st gear thrust washer pin or ball into the groove of the 1st gear thrust washer correctly.



Hide 33335C 5.INSTALL 1ST GEAR NEEDLE ROLLER BEARING

a.
C283027

Coat the 1st gear needle roller bearing with gear oil and install it to the output shaft.


Hide 33335 6.INSTALL 1ST GEAR

a.
C284596

Coat the 1st gear with gear oil and install it to the output shaft.


Hide 33037B 7.INSTALL NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR)

a.
C157311

Coat the 1st gear cone and the No. 1 synchronizer ring set (for 1st gear) with gear oil.


b.

Install the inner ring to the 1st gear.


c.
C157312

Install the middle ring to the 1st gear.


d.
C157313

Install the outer ring to the 1st gear.


Hide 33361 8.INSTALL NO. 1 TRANSMISSION CLUTCH HUB

a.
C283036N01
2.521,1.01 2.25,1.813 2.25,1.813 1.188,1.458 true 2.146,1.844 2.604,2.042 0.458,0.198 10 false SST

Using SST and a press, install the No. 1 transmission clutch hub to the output shaft.

SST
09316-60011  (09316-00031)

HINT:
·

The 1st gear can be turned.

·

While checking that the 1st gear thrust washer pin or ball is inserted into the groove of the 1st gear thrust washer, press and fit the No. 1 transmission clutch hub.




b.
C283037

Select a new No. 1 clutch hub shaft snap ring that will allow minimum axial play.

Standard clearance:

0.1 mm (0.00394 in.) or less


Snap Ring Thickness:
Part No. Mark Thickness
mm (in.)
90520-29018 A 2.50 (0.0984)
90520-29019 B 2.56 (0.1008)
90520-29020 C 2.62 (0.1031)
90520-29021 D 2.68 (0.1055)
90520-29022 E 2.74 (0.1079)
90520-29023 F 2.80 (0.1102)



c.

Using a brass bar and a hammer, install the No. 1 clutch hub shaft snap ring to the output shaft.

NOTICE:

Do not damage the journal surface of the output shaft.



Hide 33332B 9.INSTALL 2ND GEAR NEEDLE ROLLER BEARING

a.
C283038

Coat the 2nd gear needle roller bearing and the 2nd gear bearing spacer with gear oil, and install them to the output shaft.


Hide 33038E 10.INSTALL NO. 2 SYNCHRONIZER RING SET (FOR 2ND GEAR)

a.
C157314

Coat the 2nd gear cone and the No. 2 synchronizer ring set (for 2nd gear) with gear oil.


b.

Install the inner ring to the 2nd gear.


c.
C157315

Install the middle ring to the 2nd gear.


d.
C157316

Install the outer ring to the 2nd gear.


Hide 33332 11.INSTALL 2ND GEAR

a.
C283039

Coat the 2nd gear with gear oil and install it to the output shaft.


Hide 33423A 12.INSTALL 3RD DRIVEN GEAR

a.
C283040N01
2.521,1.01 2.24,1.792 2.24,1.792 1.219,1.427 true 2.135,1.813 2.594,2.01 0.458,0.198 10 false SST

Using SST and a press, install the 3rd driven gear to the output shaft.

SST
09608-00071  


Hide 33431C 13.INSTALL OUTPUT GEAR SPACER

a.
C283022

Install the output gear spacer to the output shaft.


Hide 33422B 14.INSTALL 4TH DRIVEN GEAR

a.
C283041N01
1.125,0.24 2.979,0.24 2.979,0.24 2.781,0.521 true 3.031,0.156 3.375,0.385 0.344,0.229 10 false SST

Using SST and a press, install the 4th driven gear to the output shaft.

SST
09612-22011  


Hide 33321A 15.INSTALL OUTPUT SHAFT REAR BEARING

a.
C283042N01
1.115,0.219 2.938,0.219 2.938,0.219 2.76,0.521 true 2.979,0.125 3.323,0.333 0.344,0.208 10 false SST

Using SST and a press, install the output shaft rear bearing to the output shaft.

SST
09612-22011  


Hide 16.INSPECT 2ND GEAR RADIAL CLEARANCE

a.
C283020

Using a dial indicator, measure the 2nd gear radial clearance.

Standard clearance:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 2nd gear, 2nd gear needle roller bearing or output shaft.


Hide 17.INSPECT 1ST GEAR RADIAL CLEARANCE

a.
C283019

Using a dial indicator, measure the 1st gear radial clearance.

Standard clearance:

0.015 to 0.056 mm (0.000591 to 0.00220 in.)


Maximum clearance:

0.056 mm (0.00220 in.)


If the clearance exceeds the maximum, replace the 1st gear, 1st gear needle roller bearing or output shaft.


Hide 18.INSPECT 2ND GEAR THRUST CLEARANCE

a.
C283018

Using a dial indicator, measure the 2nd gear thrust clearance.

Standard clearance:

0.10 to 0.55 mm (0.00394 to 0.0216 in.)


Maximum clearance:

0.55 mm (0.0216 in.)


If the clearance exceeds the maximum, replace the No. 1 transmission clutch hub, 2nd gear or 3rd driven gear.


Hide 19.INSPECT 1ST GEAR THRUST CLEARANCE

a.
C283017

Using a feeler gauge, measure the 1st gear thrust clearance.

Standard clearance:

0.10 to 0.40 mm (0.00394 to 0.0157 in.)


Maximum clearance:

0.40 mm (0.0157 in.)


If the clearance exceeds the maximum, replace the 1st gear thrust washer, 1st gear or No. 1 transmission clutch hub.