1. PRECAUTION
All disassembled parts should be cleaned before reassembly.
Coat all of the sliding and rotating surfaces with gear oil before reassembly, and check that they move smoothly after reassembly.
33134B
2.INSTALL OUTPUT SHAFT COVER
| *1 | Transaxle Case |
| *2 | Output Shaft Cover |
Install the output shaft cover to the transaxle case.
Insert the output shaft cover key into the case groove.
33321N
3.INSTALL OUTPUT SHAFT FRONT BEARING
Coat a new output shaft front bearing with gear oil.
Using SST and a press, install the output shaft front bearing to the transaxle case.
Install the output shaft front bearing in the correct direction as shown in the illustration.
Press in the output shaft front bearing until it is fit against the end.
31105D
4.INSTALL FRONT TRANSAXLE CASE OIL SEAL
| *a | Drive in Depth |
Using SST and a hammer, install a new front transaxle case oil seal to the transaxle case.
15.6 to 16.0 mm (0.615 to 0.629 in.)
Coat the lip of the front transaxle case oil seal with MP grease.
33311A
5.INSTALL INPUT SHAFT FRONT BEARING
Coat a new input shaft front bearing with gear oil.
| *a | Drive in Depth |
Using SST and a press, install the input shaft front bearing to the transaxle case.
0 to 0.3 mm (0 to 0.0118 in.)
41311E
6.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING
Using SST and a press, install a new front differential case front tapered roller bearing (inner race) to the differential case assembly.
Apply gear oil to the inside of a new front differential case front tapered roller bearing (outer race).
Using SST and a press, install the front differential case front tapered roller bearing (outer race) with the front differential case front plate washer to the transaxle case.
41311F
7.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING
Using SST and a press, install a new front differential case rear tapered roller bearing (inner race) to the differential case assembly.
Apply gear oil to the inside of a new front differential case rear tapered roller bearing (outer race).
Using SST and a press, install the front differential case rear tapered roller bearing (outer race) with the front differential case rear plate washer to the manual transmission case.
Use a front differential case rear plate washer of the same thickness as the removed one.
8.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD
Coat the differential case assembly with gear oil and install it to the transaxle case.
Install the manual transmission case with the 16 bolts.
Using SST and a torque wrench, turn the differential case assembly to the right and left 2 or 3 times to allow the bearings to settle.
Using SST and a torque wrench, measure the preload.
0.78 to 1.57 N*m (8.0 to 16.0 kgf*cm, 7.0 to 13.8 in.*lbf)
0.49 to 0.98 N*m (5.0 to 9.9 kgf*cm, 4.4 to 8.6 in.*lbf)
If the preload is out of the specification, select another front differential case rear plate washer.
| Part No. | Mark | Thickness
mm (in.) |
Part No. | Mark | Thickness
mm (in.) |
|---|---|---|---|---|---|
| 90564-41014 | AA | 2.10 (0.0827) | 90564-41024 | LL | 2.60 (0.1024) |
| 90564-41015 | BB | 2.15 (0.0846) | 90564-41025 | MM | 2.65 (0.1043) |
| 90564-41016 | CC | 2.20 (0.0866) | 90564-41026 | NN | 2.70 (0.1063) |
| 90564-41017 | DD | 2.25 (0.0886) | 90564-41027 | PP | 2.75 (0.1083) |
| 90564-41018 | EE | 2.30 (0.0906) | 90564-41028 | 2.80 (0.1102) | |
| 90564-41019 | FF | 2.35 (0.0925) | 90564-41029 | RR | 2.85 (0.1122) |
| 90564-41020 | GG | 2.40 (0.0945) | 90564-41030 | SS | 2.90 (0.1142) |
| 90564-41021 | HH | 2.45 (0.0965) | 90564-41031 | TT | 2.95 (0.1161) |
| 90564-41022 | JJ | 2.50 (0.0984) | 90564-41032 | UU | 3.00 (0.1181) |
| 90564-41023 | KK | 2.55 (0.1004) | - | - | - |
The preload changes by approximately 0.3 to 0.4 N*m (3.1 to 4.0 kgf*cm, 2.7 to 3.5 in.*lbf) per each 0.05 mm (0.00197 in.) change in the plate washer thickness.
Remove the 16 bolts and manual transmission case.
Remove the differential case assembly from the transaxle case.
43420H
9.INSTALL FRONT DRIVE SHAFT OIL SEAL LH
| *a | Drive in Depth |
Using SST and a hammer, install a new front drive shaft oil seal LH to the manual transmission case.
9.4 to 10.4 mm (0.371 to 0.409 in.)
Coat the lip of the front drive shaft oil seal LH with MP grease.
43410M
10.INSTALL FRONT DRIVE SHAFT OIL SEAL RH
| *a | Drive in Depth |
Using SST and a hammer, install a new front drive shaft oil seal RH to the transaxle case.
11.4 to 12 mm (0.449 to 0.472 in.)
Coat the lip of the front drive shaft oil seal RH with MP grease.
33449
11.INSTALL TRANSMISSION MAGNET
Clean the transmission magnet and install it to the transaxle case.
33326
12.INSTALL BEARING LOCK PLATE
Install the bearing lock plate to the transaxle case with the bolt.
33124D
13.INSTALL NO. 2 OIL RECEIVER PIPE
Install the No. 2 oil receiver pipe to the manual transmission case with the bolt.
Do not deform the No. 2 oil receiver pipe.
Install the No. 2 oil receiver pipe while holding it against the manual transmission case as shown in the illustration.
33124C
14.INSTALL NO. 1 OIL RECEIVER PIPE
Install the No. 1 oil receiver pipe to the manual transmission case with the bolt.
Do not deform the No. 1 oil receiver pipe.
Install the No. 1 oil receiver pipe while holding it against the manual transmission case as shown in the illustration.
33280
15.INSTALL REVERSE RESTRICT PIN ASSEMBLY
Install the reverse restrict pin assembly to the manual transmission case.
Set the reverse restrict pin assembly in the correct direction.
| *a | Drive in Depth |
Using a 5 mm pin punch and a hammer, install the reverse restrict pin slotted spring pin to the reverse restrict pin assembly.
15.5 to 16.5 mm (0.611 to 0.649 in.)
Clean and degrease the reverse restrict pin plug and installation hole.
Apply adhesive to 2 or 3 threads on the end of the reverse restrict pin plug.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Using a 6 mm hexagon socket wrench, install the reverse restrict pin plug to the manual transmission case.
33125
16.INSTALL MANUAL TRANSAXLE CASE RECEIVER
Install the manual transaxle case receiver to the transaxle case with the bolt.
17.INSTALL DIFFERENTIAL CASE ASSEMBLY
Coat the differential case assembly with gear oil and install it to the transaxle case.
18.INSTALL INPUT SHAFT ASSEMBLY
|
Gear Oil |
Apply gear oil to the entire circumference of the input shaft assembly.
To prevent the front transaxle case oil seal from being caught, make sure to apply gear oil to the input shaft assembly.
Coat the sliding and rotating surfaces of the input shaft assembly and output shaft assembly with gear oil and install them to the transaxle case.
Do not damage the front transaxle case oil seal.
33402
19.INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY
| *a | Alignment Mark |
| *b | Bolt Hole |
Coat the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft with gear oil, and install them as shown in the illustration.
Align the alignment mark on the reverse idler gear shaft with the bolt hole shown in the illustration.
33212A
20.INSTALL NO. 1 GEAR SHIFT FORK SHAFT
| *1 | No. 1 Gear Shift Fork |
| *2 | No. 2 Gear Shift Fork |
Coat the No. 1 gear shift fork and No. 2 gear shift fork with gear oil and install them.
| *1 | No. 1 Gear Shift Fork Shaft |
Coat the No. 1 gear shift fork shaft with gear oil and install it.
Clean and degrease the No. 1 gear shift fork set bolt and installation hole.
Apply adhesive to 2 or 3 threads on the end of the No. 1 gear shift fork set bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install the No. 1 gear shift fork set bolt.
Using a brass bar and a hammer, install a new shift fork shaft snap ring to the No. 1 gear shift fork shaft.
33244G
21.INSTALL NO. 3 GEAR SHIFT FORK SHAFT
Coat the 2 reverse shift fork balls with MP grease and install them to the reverse shift fork.
Install the reverse shift fork to the No. 3 gear shift fork shaft.
Secure the No. 3 gear shift fork shaft in a vise between aluminum plates.
Do not overtighten the vise.
Using a brass bar and a hammer, install 2 new shift fork shaft snap rings to the No. 3 gear shift fork shaft.
Coat the No. 3 gear shift fork shaft with gear oil and install it.
33243A
22.INSTALL NO. 2 GEAR SHIFT FORK SHAFT
Coat the No. 1 gear shift head and No. 2 gear shift fork shaft with gear oil and install them.
To avoid interference by the 2 reverse shift fork balls, lift up the No. 3 gear shift fork shaft to the position shown in the illustration.
Clean and degrease the No. 2 gear shift fork set bolt, No. 1 gear shift head set bolt and installation holes.
Apply adhesive to 2 or 3 threads on the ends of the No. 2 gear shift fork set bolt and No. 1 gear shift head set bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install the No. 2 gear shift fork set bolt and No. 1 gear shift head set bolt to the No. 2 gear shift fork and No. 1 gear shift head.
33240
23.INSTALL REVERSE SHIFT ARM BRACKET ASSEMBLY
Install the reverse shift arm bracket assembly to the transaxle case with the 2 bolts.
33111
24.INSTALL MANUAL TRANSMISSION CASE
Clean and degrease the contact surfaces of the manual transmission case and transaxle case.
| *a | Seal Packing
(Seal Diameter: 1.2 mm (0.0472 in.)) |
Apply seal packing to the manual transmission case as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.
Install the manual transmission case to the transaxle case.
| *1 | Clutch Tube Bracket |
Install the clutch tube bracket and 13 bolts to the manual transmission case.
Install the 3 bolts to the transaxle case.
33451H
25.INSTALL REVERSE IDLER GEAR SHAFT BOLT
Clean and degrease the reverse idler gear shaft bolt and installation hole.
Apply adhesive to 2 or 3 threads on the end of the reverse idler gear shaft bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install a new gasket and reverse idler gear shaft bolt to the manual transmission case.
33290
26.INSTALL NO. 1 LOCK BALL ASSEMBLY
Clean and degrease the No. 1 lock ball assembly and installation hole.
Apply adhesive to 2 or 3 threads on the end of the No. 1 lock ball assembly.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Using a 6 mm hexagon socket wrench, install the No. 1 lock ball assembly to the manual transmission case.
33275C
27.INSTALL SHIFT DETENT BALL
| *a | No. 1 Gear Shift Fork Shaft Hole |
Install the 2 shift detent balls, 2 compression springs and 2 spring seats to the manual transmission case.
Do not drop the shift detent ball into the No. 1 gear shift fork shaft hole of the manual transmission case.
Clean and degrease the 2 shift detent ball plugs and installation holes.
Apply adhesive to 2 or 3 threads on the ends of the 2 shift detent ball plugs.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Using a 6 mm hexagon socket wrench, install the 2 shift detent ball plugs to the manual transmission case.
Install the shift detent ball, compression spring and spring seat to the transaxle case.
Clean and degrease the shift detent ball plug and installation hole.
Apply adhesive to 2 or 3 threads on the end of the shift detent ball plug.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Using a 6 mm hexagon socket wrench, install the shift detent ball plug to the transaxle case.
33311X
28.INSTALL INPUT SHAFT REAR BEARING HOLE SNAP RING
Using a snap ring expander, install a new input shaft rear bearing hole snap ring to the input shaft.
Do not expand the input shaft rear bearing hole snap ring excessively.
33111R
29.INSTALL OUTPUT SHAFT REAR BEARING HOLE SNAP RING
Using a snap ring expander, install a new output shaft rear bearing hole snap ring to the output shaft.
Do not expand the output shaft rear bearing hole snap ring excessively.
33242E
30.INSTALL SHIFT FORK SHAFT SNAP RING
Using a brass bar and a hammer, install a new shift fork shaft snap ring to the No. 2 gear shift fork shaft.
33151D
31.INSTALL REAR BEARING RETAINER
Clean and degrease the 5 bolts and installation holes.
Apply adhesive to 2 or 3 threads on the ends of the 5 bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install the rear bearing retainer to the manual transmission case with the 5 bolts.
33428C
32.INSTALL 5TH DRIVEN GEAR
| *a | Hold |
| *b | Turn |
Using SST, install the 5th driven gear to the output shaft.
33336A
33.INSTALL 5TH GEAR NEEDLE ROLLER BEARING
| *1 | 5th Gear Needle Roller Bearing |
| *2 | 5th Gear Bearing Spacer |
Coat the 5th gear needle roller bearing and 5th gear bearing spacer with gear oil, and install them to the input shaft.
33336
34.INSTALL 5TH GEAR
Coat the 5th gear with gear oil and install it to the input shaft.
33369
35.INSTALL NO. 3 SYNCHRONIZER RING
Coat the No. 3 synchronizer ring with gear oil and install it to the 5th gear.
33393
36.INSTALL NO. 3 TRANSMISSION CLUTCH HUB
| *a | Wooden Block |
Place a suitable sized wooden block to support the input shaft.
| *a | Engine Side |
Install the 3 synchromesh shifting keys and 2 synchromesh shifting key springs to the No. 3 transmission clutch hub as shown in the illustration.
Do not set the 2 shifting key spring openings in the same position.
| *1 | 5th Gear |
| *a | Key Groove Position |
| *b | Engine Side |
Using SST and a hammer, install the No. 3 transmission clutch hub to the input shaft.
Do not install the No. 3 transmission clutch hub in the wrong direction.
Install the No. 3 transmission clutch hub with the No. 3 synchronizer ring key groove and No. 3 synchromesh shifting key aligned.
Check that the 5th gear is rotating.
Select a snap ring that will allow minimum axial play.
0.1 mm (0.00394 in.) or less
| Part No. | Mark | Thickness
mm (in.) |
|---|---|---|
| 90520-18002 | A | 2.25 (0.0886) |
| 90520-18003 | B | 2.31 (0.0909) |
| 90520-18004 | C | 2.37 (0.0933) |
| 90520-18006 | D | 2.43 (0.0957) |
| 90520-18007 | E | 2.49 (0.0980) |
| 90520-18008 | F | 2.55 (0.1004) |
| 90520-18009 | G | 2.61 (0.1028) |
Using a brass bar and a hammer, install a new snap ring to the input shaft.
37.INSPECT 5TH GEAR THRUST CLEARANCE
Using a dial indicator, measure the 5th gear thrust clearance.
0.10 to 0.55 mm (0.00394 to 0.0216 in.)
0.55 mm (0.0216 in.)
If the clearance exceeds the maximum, replace the No. 3 transmission clutch hub, 5th gear or input shaft rear radial ball bearing.
38.INSPECT 5TH GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 5th gear radial clearance.
0.015 to 0.056 mm (0.000591 to 0.00220 in.)
0.056 mm (0.00220 in.)
If the clearance exceeds the maximum, replace the 5th gear, 5th gear needle roller bearing or input shaft.
33214G
39.INSTALL NO. 3 GEAR SHIFT FORK
Coat the No. 3 transmission hub sleeve with gear oil and install it with the No. 3 gear shift fork to the No. 3 transmission clutch hub.
Set the No. 3 transmission clutch hub in the correct direction.
Clean and degrease the No. 3 gear shift fork set bolt and installation hole.
Apply adhesive to 2 or 3 threads on the end of the No. 3 gear shift fork set bolt.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install the No. 3 gear shift fork set bolt to the No. 3 gear shift fork.
33321G
40.INSTALL MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT
Engage the 2 gears simultaneously to lock the transmission.
Using a 27 mm socket wrench, install a new manual transmission output shaft rear set nut.
Using a chisel and a hammer, stake the manual transmission output shaft rear set nut.
Disengage the 2 gears.
33102
41.INSTALL MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY
Clean and degrease the contact surfaces of the manual transmission case cover sub-assembly and manual transmission case.
| *a | Seal Packing
(Seal Diameter 1.2 mm (0.0742 in.) |
Apply seal packing to the manual transmission case cover sub-assembly as shown in the illustration.
Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent
Assemble the parts within 10 minutes of application. Otherwise, the seal packing material must be removed and reapplied.
Clean and degrease the 9 bolts and installation holes.
Apply adhesive to 2 or 3 threads on the ends of the 9 bolts.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install the manual transmission case cover sub-assembly to the manual transmission case with the 9 bolts.
42.INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY
Clean and degrease the 2 bolts A and installation holes.
Coat the shift and select lever shaft assembly with gear oil.
Apply adhesive to 2 or 3 threads on the ends of the 2 bolts A.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install a new gasket and the shift and select lever shaft assembly to the manual transmission case with the 4 bolts.
Set the claws of the shift interlock plate into the shift head part of the gear shift fork shaft securely.
33266A
43.INSTALL SHIFT INTERLOCK PLATE BOLT (for TMMIN Made)
Install a new gasket and shift interlock plate bolt to the manual transmission case.
33290B
44.INSTALL NO. 2 LOCK BALL ASSEMBLY (for TMT Made)
Clean and degrease the No. 2 lock ball assembly and installation hole.
Apply adhesive to 2 or 3 threads on the ends of the No. 2 lock ball assembly.
Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install the No. 2 lock ball assembly to the manual transmission case.
33295A
45.INSTALL REVERSE RESTRICT SHAFT
Clean and degrease the reverse restrict shaft and installation hole.
Apply adhesive to 2 or 3 threads on the end of the reverse restrict shaft.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
To prevent contamination by foreign matter, install immediately after applying adhesive.
Install the washer and reverse restrict shaft to the manual transmission case.
33544C
46.INSTALL SHIFT LEVER DAMPER
Install the shift lever damper to the shift and select lever shaft assembly with the 2 bolts.
33590F
47.INSTALL FLOOR SHIFT SELECTING BELL CRANK ASSEMBLY
| *1 | Floor Shift Selecting Bellcrank Assembly |
| *2 | Control Bellcrank Dust Cover |
Coat the inside circumferential surface of the control bellcrank dust cover with MP grease and install it to the floor shift selecting bellcrank assembly.
Install the floor shift selecting bellcrank assembly with control bellcrank dust cover to the manual transmission case with the 2 bolts.
33111G
48.INSTALL MANUAL TRANSMISSION BREATHER PLUG
Using SST and a hammer, install the manual transmission breather plug to the manual transmission case.
84210
49.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY
Using a 27 mm socket wrench, install a new gasket and back-up light switch assembly to the manual transmission case.
33104
50.INSTALL DRAIN PLUG SUB-ASSEMBLY
Install a new gasket and drain plug sub-assembly to the manual transmission case.
33101A
51.INSTALL MANUAL TRANSMISSION FILLER PLUG
Install a new gasket and manual transmission filler plug to the manual transmission case.
33823
52.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
Install the No. 1 transmission control cable bracket to the manual transmission case with the 3 bolts.
31236B
53.INSTALL RELEASE FORK SUPPORT
31126
54.INSTALL CLUTCH RELEASE FORK BOOT
31232A
55.INSTALL RELEASE BEARING HUB CLIP
31204
56.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY
31230
57.INSTALL CLUTCH RELEASE BEARING ASSEMBLY