33321
1.INSPECT OUTPUT SHAFT
Using a dial indicator and 2 V-blocks, measure the output shaft runout.
0.015 mm (0.000591 in.)
If the runout exceeds the maximum, replace the output shaft.
Using a micrometer, measure the outer diameter of the output shaft journal surface at the locations indicated.
31.985 to 32.000 mm (1.2593 to 1.2598 in.)
37.985 to 38.000 mm (1.4955 to 1.4961 in.)
32.985 to 33.000 mm (1.2986 to 1.2992 in.)
31.985 mm (1.2593 in.)
37.985 mm (1.4955 in.)
32.985 mm (1.2986 in.)
If any of the outer diameters are less than the minimum, replace the output shaft.
33332
2.INSPECT 2ND GEAR
Using a cylinder gauge, measure the inside diameter of the 2nd gear.
38.015 to 38.031 mm (1.4967 to 1.4972 in.)
38.031 mm (1.4972 in.)
If the inside diameter exceeds the maximum, replace the 2nd gear.
33335
3.INSPECT 1ST GEAR
Using a cylinder gauge, measure the inside diameter of the 1st gear.
44.015 to 44.031 mm (1.7329 to 1.7335 in.)
44.031 mm (1.7335 in.)
If the inside diameter exceeds the maximum, replace the 1st gear.
33348
4.INSPECT 1ST GEAR THRUST WASHER
Using a micrometer, measure the 1st gear thrust washer thickness.
5.975 to 6.025 mm (0.2353 to 0.2372 in.)
5.975 mm (0.2353 in.)
If the thickness is less than the minimum, replace the 1st gear thrust washer.
33038E
5.INSPECT NO. 2 SYNCHRONIZER RING SET (FOR 2ND GEAR)
| *a | Locks and cannot rotate |
Check for wear and damage.
Coat the 2nd gear cone and the No. 2 synchronizer ring set (for 2nd gear) with gear oil.
Turn the No. 2 synchronizer ring set (for 2nd gear) in one direction while pushing it against the 2nd gear cone.
Check that the No. 2 synchronizer ring set (for 2nd gear) locks.
If the No. 2 synchronizer ring set (for 2nd gear) does not lock, replace it.
Using a feeler gauge, measure the clearance between the synchronizer ring and the gear spline end.
0.7 to 1.3 mm (0.0276 to 0.0511 in.)
0.7 mm (0.0276 in.)
If the clearance is less than the minimum, replace the No. 2 synchronizer ring set (for 2nd gear).
6.INSPECT 1ST GEAR SYNCHRONIZER RING (for TMMIN Made)
| *a | Locks and cannot rotate |
Check for wear and damage.
Coat the 1st gear cone with gear oil.
Turn the 1st gear synchronizer ring in one direction while pushing it against the 1st gear cone.
Check that the 1st gear synchronizer ring locks.
If the 1st gear synchronizer ring does not lock, replace it.
Using a feeler gauge, measure the clearance between the 1st gear synchronizer ring and the gear spline end.
0.75 to 1.65 mm (0.0296 to 0.0649 in.)
0.75 mm (0.0296 in.)
If the clearance is less than the minimum, replace the 1st gear synchronizer ring.
33037B
7.INSPECT NO. 1 SYNCHRONIZER RING SET (for TMT Made)
| *a | Locks and cannot rotate |
Check for wear and damage.
Coat the 1st gear cone and the No. 1 synchronizer ring set (for 1st gear) with gear oil.
Turn the No. 1 synchronizer ring set (for 1st gear) in one direction while pushing it against the 1st gear cone.
Check that the No. 1 synchronizer ring set (for 1st gear) locks.
If the No. 1 synchronizer ring set (for 1st gear) does not lock, replace it.
Using a feeler gauge, measure the clearance between the synchronizer ring and the gear spline end.
0.6 to 1.4 mm (0.0236 to 0.0551 in.)
0.6 mm (0.0236 in.)
If the clearance is less than the minimum, replace the No. 1 synchronizer ring set (for 1st gear).
33331
8.INSPECT REVERSE GEAR
Using a vernier caliper, measure the width of the reverse gear groove (A) and the thickness of the claw part on the reverse shift fork (B), and calculate the clearance.
0.15 to 0.35 mm (0.00591 to 0.0137 in.)
If the clearance is not as specified, replace the reverse gear and the reverse shift fork.
33361
9.INSPECT NO. 1 TRANSMISSION CLUTCH HUB
Check that the No. 1 transmission clutch hub and the reverse gear slide smoothly.
Check that the edges of the reverse gear spline gear are not worn down.