1. PRECAUTION
All disassembled parts should be cleaned before reassembly.
Coat all of the sliding and rotating surfaces with gear oil before reassembly, and check that they move smoothly after reassembly.
33331
2.INSTALL REVERSE GEAR
Coat the reverse gear and the No. 1 transmission clutch hub with gear oil.
Install the 3 synchromesh shifting key springs and the 3 synchromesh shifting keys to the No. 1 transmission clutch hub.
Install the reverse gear to the No. 1 transmission clutch hub.
Position the reverse gear and the No. 1 transmission clutch hub correctly as shown in the illustration.
33348A
3.INSTALL 1ST GEAR THRUST WASHER PIN OR BALL
Coat the 1st gear thrust washer pin or ball with MP grease and install it to the output shaft.
33348
4.INSTALL 1ST GEAR THRUST WASHER
Coat the 1st gear thrust washer with gear oil and install it to the output shaft.
Fit the 1st gear thrust washer pin or ball into the groove of the 1st gear thrust washer correctly.
33335C
5.INSTALL 1ST GEAR NEEDLE ROLLER BEARING
Coat the 1st gear needle roller bearing with gear oil and install it to the output shaft.
33335
6.INSTALL 1ST GEAR
Coat the 1st gear with gear oil and install it to the output shaft.
7.INSTALL 1ST GEAR SYNCHRONIZER RING (for TMMIN Made)
Coat the 1st gear synchronizer ring with gear oil and install it to the 1st gear.
33037B
8.INSTALL NO. 1 SYNCHRONIZER RING SET (FOR 1ST GEAR) (for TMT Made)
Coat the 1st gear cone and the No. 1 synchronizer ring set (for 1st gear) with gear oil.
Install the inner ring to the 1st gear.
Install the middle ring to the 1st gear.
Install the outer ring to the 1st gear.
33361
9.INSTALL NO. 1 TRANSMISSION CLUTCH HUB
Using SST and a press, install the No. 1 transmission clutch hub to the output shaft.
The 1st gear can be turned.
While checking that the 1st gear thrust washer pin or ball is inserted into the groove of the 1st gear thrust washer, press and fit the No. 1 transmission clutch hub.
Select a new No. 1 clutch hub shaft snap ring that will allow minimum axial play.
0.1 mm (0.00394 in.) or less
| Part No. | Mark | Thickness
mm (in.) |
|---|---|---|
| 90520-29018 | A | 2.50 (0.0984) |
| 90520-29019 | B | 2.56 (0.1008) |
| 90520-29020 | C | 2.62 (0.1031) |
| 90520-29021 | D | 2.68 (0.1055) |
| 90520-29022 | E | 2.74 (0.1079) |
| 90520-29023 | F | 2.80 (0.1102) |
Using a brass bar and a hammer, install the No. 1 clutch hub shaft snap ring to the output shaft.
Do not damage the journal surface of the output shaft.
33332B
10.INSTALL 2ND GEAR NEEDLE ROLLER BEARING
Coat the 2nd gear needle roller bearing and the 2nd gear bearing spacer with gear oil, and install them to the output shaft.
33038E
11.INSTALL NO. 2 SYNCHRONIZER RING SET (FOR 2ND GEAR)
Coat the 2nd gear cone and the No. 2 synchronizer ring set (for 2nd gear) with gear oil.
Install the inner ring to the 2nd gear.
Install the middle ring to the 2nd gear.
Install the outer ring to the 2nd gear.
33332
12.INSTALL 2ND GEAR
Coat the 2nd gear with gear oil and install it to the output shaft.
33423A
13.INSTALL 3RD DRIVEN GEAR
Using SST and a press, install the 3rd driven gear to the output shaft.
33431C
14.INSTALL OUTPUT GEAR SPACER
Install the output gear spacer to the output shaft.
33422B
15.INSTALL 4TH DRIVEN GEAR
Using SST and a press, install the 4th driven gear to the output shaft.
33321A
16.INSTALL OUTPUT SHAFT REAR BEARING
Using SST and a press, install the output shaft rear bearing to the output shaft.
17.INSPECT 2ND GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 2nd gear radial clearance.
0.015 to 0.056 mm (0.000591 to 0.00220 in.)
0.056 mm (0.00220 in.)
If the clearance exceeds the maximum, replace the 2nd gear, 2nd gear needle roller bearing or output shaft.
18.INSPECT 1ST GEAR RADIAL CLEARANCE
Using a dial indicator, measure the 1st gear radial clearance.
0.015 to 0.056 mm (0.000591 to 0.00220 in.)
0.056 mm (0.00220 in.)
If the clearance exceeds the maximum, replace the 1st gear, 1st gear needle roller bearing or output shaft.
19.INSPECT 2ND GEAR THRUST CLEARANCE
Using a dial indicator, measure the 2nd gear thrust clearance.
0.10 to 0.55 mm (0.00394 to 0.0216 in.)
0.55 mm (0.0216 in.)
If the clearance exceeds the maximum, replace the No. 1 transmission clutch hub, 2nd gear or 3rd driven gear.
20.INSPECT 1ST GEAR THRUST CLEARANCE
Using a feeler gauge, measure the 1st gear thrust clearance.
0.10 to 0.40 mm (0.00394 to 0.0157 in.)
0.40 mm (0.0157 in.)
If the clearance exceeds the maximum, replace the 1st gear thrust washer, 1st gear or No. 1 transmission clutch hub.