Home › Drivetrain › K312 CVT › SHIFT LEVER(for TMT Made) › 2017.10–2018.01
RM30M0E _52 Drivetrain _052969 K312 CVT _0333889 SHIFT LEVER(for TMT Made) G

K312 CVT  SHIFT LEVER(for TMT Made)  INSPECTION  


PROCEDURE

Hide 33550 1.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (w/ Smart Entry and Start System)

HINT:

If the results of the following inspections are as specified but a malfunction has occurred, replace the shift lock control unit assembly.


a.

Inspect the wire harness.

i.

Disconnect the shift lock control ECU connector.


ii.
C375308C08
2,1 2.333,0.333 2.333,0.333 2.5,0.333 true 2,1.333 2.188,1.833 2.188,1.833 2.333,1.833 true 2.552,0.26 2.865,0.458 0.313,0.198 10 false IG 2.448,1.76 2.76,1.958 0.313,0.198 10 false STP 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Shift Lock Control ECU (Shift Lock Control Unit Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
4 (IG) - Body ground Engine switch on (IG) 11 to 14 V
Engine switch off Below 1 V
8 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V


If the result is not as specified, repair or replace the wire harness or connector.


iii.
C375308C09
2.188,1.781 1.802,1.333 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 2.25,1.781 2.406,1.979 0.156,0.198 10 false E
*a Front view of wire harness connector
(to Shift Lock Control ECU (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the wire harness or connector.



b.

Inspect the shift lock solenoid.

i.

Disconnect the shift lock solenoid connector.


ii.
C197452C44
0.802,1.521 1.365,1.25 true 1.135,1.802 1.594,1.25 true 2.063,1.25 2.615,1.542 true 2.281,1.802 1.844,1.25 true 0.083,0.083 0.292,0.271 0.208,0.188 10 false *a 2.677,1.5 2.833,1.698 0.156,0.198 10 false P 2.333,1.74 2.583,1.927 0.25,0.188 10 false E2 0.771,1.75 1.198,1.938 0.427,0.188 10 false SLS- 0.438,1.469 0.885,1.667 0.448,0.198 10 false SLS+
*a Component without harness connected
(Shift Lock Control ECU (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 112 Ω
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω


If the result is not as specified, replace the shift lock control unit assembly.



Hide 33560 2.INSPECT SHIFT LOCK CONTROL UNIT ASSEMBLY (w/o Smart Entry and Start System)

HINT:

If the results of the following inspections are as specified but a malfunction has occurred, replace the shift lock control unit assembly.


a.

Inspect the wire harness.

i.

Disconnect the shift lock control ECU connector.


ii.
C375308C10
0.906,0.417 1.406,0.99 true 2.552,0.427 2.042,1 true 1.438,1.344 1.073,1.833 true 1.979,1.333 2.375,1.781 true 2.583,0.25 2.896,0.448 0.313,0.198 10 false IG 2.448,1.76 2.76,1.958 0.313,0.198 10 false STP 0.083,0.115 0.396,0.313 0.313,0.198 10 false *a 0.594,0.292 0.906,0.49 0.313,0.198 10 false ACC 0.688,1.771 1.094,1.969 0.406,0.198 10 false KLS+
*a Front view of wire harness connector
(to Shift Lock Control ECU (Shift Lock Control Unit Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1 (ACC) - Body ground Ignition switch ACC 11 to 14 V
Ignition switch off Below 1 V
4 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
5 (KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V
Ignition switch ACC and shift lever not in P 11 to 14 V
8 (STP) - Body ground Brake pedal depressed 11 to 14 V
Brake pedal released Below 1 V


If the result is not as specified, repair or replace the wire harness or connector.


iii.
C375308C09
2.188,1.781 1.802,1.333 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 2.25,1.781 2.406,1.979 0.156,0.198 10 false E
*a Front view of wire harness connector
(to Shift Lock Control ECU (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (E) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the wire harness or connector.



b.

Inspect the shift lock solenoid.

i.

Disconnect the shift lock solenoid connector.


ii.
C197452C24
1.365,1.24 0.854,1.552 true 1.604,1.24 1.375,1.635 true 1.833,1.25 2.031,1.646 true 2.083,1.24 2.583,1.552 true 0.479,1.49 0.854,1.698 0.375,0.208 10 false SLS+ 1.25,1.656 1.646,1.865 0.396,0.208 10 false SLS- 1.969,1.656 2.198,1.865 0.229,0.208 10 false E2 2.635,1.49 2.865,1.698 0.229,0.208 10 false P 0.115,0.094 0.427,0.25 0.313,0.156 10 false *a
*a Component without harness connected
(Shift Lock Control ECU (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SLS+) - 2 (SLS-) Always 112 Ω
4 (P) - 3 (E2) Shift lever in P 10 kΩ or higher
Shift lever not in P Below 1 Ω


·

If the result is not as specified, replace the shift lock control unit assembly.

·

If the shift lock does not operate when the power source of the shift lock control unit assembly is normal and the resistance values of the body ground and the shift lock solenoid are as specified, replace the shift lock control unit assembly.




Hide 3.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY) (for LHD)

a.

Disconnect the connector from the shift lock control unit assembly.


b.
C271753C07
1.906,1.083 2.198,0.375 true 2.417,1.875 2.083,1.198 true 1.438,1.906 1.729,1.198 true 0.052,0.052 0.26,0.25 0.208,0.198 10 false *a 2.24,0.271 2.396,0.438 0.156,0.167 10 false E 1.115,1.896 1.542,2.073 0.427,0.177 10 false SFTU 2.417,1.896 2.833,2.083 0.417,0.188 10 false SFTD
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SFTD) - 2 (E) Shift lever held in "-" (Downshift) Below 1 Ω
Shift lever not in "-" 10 kΩ or higher
3 (SFTU) - 2 (E) Shift lever held in "+" (Upshift) Below 1 Ω
Shift lever not in "+" 10 kΩ or higher


If the result is not as specified, replace the shift lock control unit assembly.


Hide 4.INSPECT TRANSMISSION CONTROL SWITCH (SHIFT LOCK CONTROL UNIT ASSEMBLY) (for RHD)

a.

Disconnect the transmission control switch connector.


b.
C271753C06
1.906,1.083 2.198,0.375 true 2.417,1.875 2.083,1.198 true 1.438,1.906 1.729,1.198 true 0.052,0.052 0.26,0.25 0.208,0.198 10 false *a 2.24,0.271 2.396,0.438 0.156,0.167 10 false E 2.458,1.885 2.885,2.063 0.427,0.177 10 false SFTU 1.073,1.865 1.49,2.052 0.417,0.188 10 false SFTD
*a Component without harness connected
(Transmission Control Switch (Shift Lock Control Unit Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SFTU) - 2 (E) Shift lever held in "+" (Upshift) Below 1 Ω
Shift lever not in "+" 10 kΩ or higher
3 (SFTD) - 2 (E) Shift lever held in "-" (Downshift) Below 1 Ω
Shift lever not in "-" 10 kΩ or higher


If the result is not as specified, replace the shift lock control unit assembly.