Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2017.10–2018.01
RM30M0E _54 Brake _017098 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0256246 VEHICLE STABILITY CONTROL SYSTEM D

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  SYSTEM DESCRIPTION  


FUNCTION DESCRIPTION


a.

ABS (Anti-lock Brake System)

i.

The ABS helps prevent the wheels from locking when the brakes are applied firmly or when braking on a slippery surface.



b.

EBD (Electronic Brake force Distribution)

i.

The EBD control utilizes ABS, and performs proper brake force distribution between the front and rear wheels in accordance with driving conditions. When braking while cornering, it also controls the brake forces of the right and left wheels, helping to maintain vehicle stability.



c.

BA (Brake Assist)

i.

The primary purpose of the brake assist system is to provide auxiliary brake force to assist the driver if the driver cannot generate a large enough brake force during emergency braking, thus helping to maximize the brake performance of the vehicle.



d.

TRC (Traction Control)

i.

The TRC system helps prevent the drive wheels from slipping when the driver depresses the accelerator pedal excessively when starting off or accelerating on a slippery surface.



e.

VSC (Vehicle Stability Control)

i.

The VSC system helps prevent the vehicle from slipping sideways as a result of strong front or rear wheel skid during cornering.



f.

Hill-start Assist Control (for TMT Made)

i.

When starting uphill, this control maintains the brake hydraulic pressure to the 4 wheels, in order to momentarily prevent the vehicle from descending backward.




FUNCTION OF COMPONENTS


Component Function
Speed sensor Detects the wheel speed and sends the signal to the skid control ECU (brake actuator assembly).
Yaw rate and acceleration sensor (airbag sensor assembly)
·

Acceleration sensor measures the capacity of the condenser that changes the distance between the electrodes depending on G force, which occurs when the vehicle is accelerated, and converts the measured value into electrical signals.

·

Yaw rate sensor detects the vehicle's angular velocity (yaw rate) in the vertical direction based on the amount and direction of the piezoelectric ceramics deflection.

·

Sends signals to the skid control ECU (brake actuator assembly) via CAN communication.


Steering angle sensor*1
Steering angle sensor (Spiral cable sub-assembly)*2
·

Detects the steering amount and direction and sends the signals to the skid control ECU (brake actuator assembly) via CAN communication.

·

Has a magnetic resistance element which detects the rotation of the magnet housed in the detection gear in order to detect the changes in magnetic resistance and the steering amount and direction.


Stop light switch assembly Detects the brake operating conditions and inputs the results to the skid control ECU (brake actuator assembly).
Combination meter assembly Detects the parking brake operating conditions and inputs the results to the skid control ECU (brake actuator assembly) via CAN communication.
Master cylinder pressure sensor
·

Detects the fluid pressure in the master cylinder.

·

Housed in the brake actuator assembly.


Skid control ECU
·

Housed in the brake actuator assembly.

·

Processes the signals sent from each sensor to control the ABS, EBD, BA, TRC, and VSC.

·

Sends and receives the control signals to or from the ECM, yaw rate and acceleration sensor, and steering angle sensor, etc. via CAN communication.


Brake actuator assembly
·

Consists of the master cylinder cut solenoid valve, retention solenoid valve, pressure reduction solenoid valve, pump motor, and reservoir, and adjusts the brake fluid pressure applied to each wheel cylinder.

·

Houses the skid control ECU.


Motor relay
·

Supplies power to the pump motor.

·

Housed in the brake actuator assembly.


Motor fail safe relay
·

Cuts off power to the motor when the pump motor circuit malfunctions.

·

Housed in the brake actuator assembly.


Solenoid relay
·

Supplies power to each solenoid.

·

Housed in the brake actuator assembly.


ABS warning light
·

Comes on to inform the driver that a malfunction in the ABS and/or BA has occurred.

·

Blinks to output DTC.


Brake warning light
·

Comes on to inform the driver that the parking brake is ON when the system is normal, or that the brake fluid has decreased.

·

Comes on to inform the driver that a malfunction in the EBD has occurred.


TRC OFF indicator light*3 Comes on to inform the driver when the TRC OFF mode is entered using VSC OFF switch.
Multi-information Display (TRC OFF Message)*4 Displays the information message when TRC off mode or VSC off mode is selected.
VSC OFF indicator light Comes on to inform the driver when the VSC OFF mode is entered using VSC OFF switch.
SLIP indicator light
·

Lights up together with the VSC OFF indicator light to alert the driver when the skid control ECU (brake actuator assembly) detects a malfunction in TRC or VSC.

·

Blinks to output DTC.

·

Blinks to inform the driver that TRC and/or VSC are operating.


ECM Controls the engine output when TRC and/or VSC are operating with the skid control ECU (brake actuator assembly) via CAN communication.
VSC OFF switch Pressing this switch turns off traction control and pressing and holding this switch turns off traction and VSC controls.

*1: for TMT Made

*2: for TMMIN Made

*3: for Segment Display Type

*4: for TFT Display Type