DESCRIPTION
After replacing any VSC related components or performing wheel alignment adjustment, clear and read the sensor calibration data.
Refer to the table below and then perform the necessary operation according to the part to be replaced in order to perform calibration.
| Parts to be Replaced / Operation | Necessary Operation |
|---|---|
| Skid control ECU (brake actuator assembly) | Perform yaw rate and acceleration sensor zero point calibration and store system information. |
| Yaw rate and acceleration sensor (airbag ECU assembly) | 1.
Clear zero point calibration data and store system information. 2.
Perform yaw rate and acceleration sensor zero point calibration and store system information. |
| Wheel alignment adjustment | 1.
Clear zero point calibration data and store system information. 2.
Perform yaw rate and acceleration sensor zero point calibration and store system information. |
PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION AND STORE SYSTEM INFORMATION (When Using GTS)
Stored system information cannot be overwritten unless it is cleared. Clear the stored information and then store new system information.
While obtaining the zero points, keep the vehicle stationary and do not vibrate, tilt, move, or shake it (do not start the engine).
Be sure to perform this procedure on a level surface (with an inclination of less than 1 degree).
Clear the zero point calibration data and store system information.
Performing the following procedure will clear the zero points of the yaw rate and acceleration sensor and system information simultaneously.
Turn the ignition switch off.
Check that the steering wheel is centered.
Check that the shift lever is in P (for Continuously Variable Transaxle).
Check that the shift lever is in neutral and the parking brake is applied (for Manual Transaxle).
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Select the skid control ECU (brake actuator assembly) to clear the zero point calibration data using the GTS.
Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Reset Memory.
| Tester Display |
|---|
| Reset Memory |
Check that the slip indicator light comes on.
Turn the ignition switch off.
If the ignition switch is turned to ON for more than 15 seconds with the shift lever in P (for Continuously Variable Transaxle) or the parking brake applied (for manual transaxle) after the zero point of the yaw rate and acceleration sensor has been cleared, only the zero point of the yaw rate sensor will be stored. If the vehicle is driven under these conditions, the skid control ECU (brake actuator assembly) will store the zero point calibration for the acceleration sensor as not being completed. The skid control ECU (brake actuator assembly) will then also indicate this as a malfunction of the VSC system using the indicator light.
Perform the yaw rate and acceleration sensor zero point calibration and store system information.
Performing the following procedure will perform the yaw rate and acceleration sensor zero point calibration and store system information simultaneously.
Turn the ignition switch off.
Check that the steering wheel is centered.
Check that the shift lever is in P (for Continuously Variable Transaxle).
Check that the shift lever is in neutral and the parking brake is applied (for Manual Transaxle).
DTCs C1210 (Zero Point Calibration of Yaw Rate Sensor Undone) and C1336 (Zero Point Calibration of Acceleration Sensor Undone) will be stored if the shift lever is not in P (for Continuously Variable Transaxle) or the parking brake is not applied (for manual transaxle).
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Switch the skid control ECU (brake actuator assembly) to Test Mode using the GTS.
Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Test Mode.
| Tester Display |
|---|
| Test Mode |
After the Test Mode has been entered, keep the vehicle stationary on a level surface for 5 seconds or more.
Check that the slip indicator light comes on for several seconds and then blinks in the Test Mode pattern.
If the slip indicator light does not blink, perform zero point calibration again.
The zero point calibration is performed only once after the system enters the Test Mode.
Calibration cannot be performed again until the stored data is cleared.
Turn the ignition switch off and disconnect the GTS.
PERFORM YAW RATE AND ACCELERATION SENSOR ZERO POINT CALIBRATION AND STORE SYSTEM INFORMATION (When Using SST Check Wire) (for TMMIN Made)
Stored system information cannot be overwritten unless it is cleared. Clear the stored information and then store new system information.
While obtaining the zero points, keep the vehicle stationary and do not vibrate, tilt, move, or shake it (do not start the engine).
Be sure to perform this procedure on a level surface (with an inclination of less than 1 degree).
Clear the zero point calibration data and store system information.
Performing the following procedure will clear the zero points of the yaw rate and acceleration sensor and system information simultaneously.
Turn the ignition switch off.
Check that the steering wheel is centered.
Check that the shift lever is in P (for Continuously Variable Transaxle).
Check that the shift lever is in neutral and the parking brake is applied (for Manual Transaxle).
Turn the ignition switch to ON.
| *a | Front view of DLC3 |
Using SST, connect and disconnect terminals 12 (TS) and 4 (CG) of the DLC3 4 times or more within 8 seconds.
Check that the slip indicator light comes on.
If the vehicle is driven after the zero point of the yaw rate and acceleration sensor and system information are cleared, DTCs will be stored.
If the ignition switch is turned to ON for more than 15 seconds with the shift lever in P after the zero point of the yaw rate and acceleration sensor has been cleared, only the zero point of the yaw rate sensor will be stored. If the vehicle is driven under these conditions, the skid control ECU (brake actuator assembly) will store the zero point calibration for the acceleration sensor as not being completed. The skid control ECU (brake actuator assembly) will then also indicate this as a malfunction of the VSC system using the indicator light.
Turn the ignition switch off.
Perform the yaw rate and acceleration sensor zero point calibration and store system information.
Performing the following procedure will perform the yaw rate and acceleration sensor zero point calibration, and also store system information simultaneously.
Turn the ignition switch off.
Check that the steering wheel is centered.
Check that the shift lever is in P (for Continuously Variable Transaxle).
Check that the shift lever is in neutral and the parking brake is applied (for Manual Transaxle).
DTCs 36 (Zero Point Calibration of Yaw Rate Sensor Undone) and 39 (Zero Point Calibration of Acceleration Sensor Undone) will be stored if the shift lever is not in P (for Continuously Variable Transaxle) or the parking brake is not applied (for manual transaxle).
| *a | Front view of DLC3 |
Using SST, connect terminals 12 (TS) and 4 (CG) of the DLC3.
Turn the ignition switch to ON.
After Test Mode has been entered, keep the vehicle stationary on a level surface for 5 seconds or more.
Check that the slip indicator light comes on for several seconds and then blinks in the Test Mode pattern.
If the slip indicator light does not blink, perform zero point calibration again.
The zero point calibration is performed only once after the system enters the Test Mode.
Calibration cannot be performed again until the stored data is cleared.
Turn the ignition switch off and disconnect SST from the DLC3.