WARNING LIGHT AND INDICATOR LIGHT INITIAL CHECK
Release the parking brake.
Before releasing the parking brake, move the shift lever to P (for Continuously Variable Transaxle) or use wheel chocks to secure the vehicle (for Manual Transaxle).
When the parking brake is applied or the brake fluid level is low, the brake warning light comes on.
When the ignition switch is turned to ON, check that the ABS warning, brake warning, light, TRC OFF indicator light*1, Multi-information Display (TRC OFF Message)*2, VSC OFF indicator light and slip indicator light all come on for approximately 3 seconds.
*1: for Segment Display Type
*2: for TFT Display Type
If the skid control ECU (brake actuator assembly) stores a DTC, the ABS warning and slip indicator lights will come on.
If any of the indicators remains on or does not come on, proceed to troubleshooting for the light circuits listed below.
SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using GTS)
If the ignition switch is turned from ON to ACC or off during Test Mode (signal check), DTCs recorded during the sensor check will be cleared.
During Test Mode (signal check), the skid control ECU (brake actuator assembly) records all DTCs detected in the sensor check. By performing Test Mode (signal check), the codes are cleared as the normal condition for each item is confirmed. The remaining codes are the codes where an abnormality was found.
Procedure to enter Test Mode
Turn the ignition switch off.
Check that the steering wheel is centered.
Apply the parking brake.
Check that the shift lever is in P (for Continuously Variable Transaxle).
Check that the shift lever is in neutral and the parking brake is applied (for Manual Transaxle).
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Switch the skid control ECU (brake actuator assembly) to Test Mode using the GTS. Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.
| Tester Display |
|---|
| Signal Check |
Check that the ABS warning and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.
If the ABS warning and slip indicator lights do not blink, inspect the ABS warning and slip indicator light circuits.
Check the ABS sensors.
Check that the ABS warning light is blinking in the Test Mode pattern before performing the following ABS sensor checks.
Acceleration Sensor Check
Keep the vehicle stationary on a level surface for 1 second or more.
The acceleration sensor check can be performed by following the master cylinder pressure sensor check procedure below.
Master Cylinder Pressure Sensor Check
Keep the vehicle stationary without the brake pedal depressed for 1 second or more. After that, depress the brake pedal quickly and strongly with a force of more than 98 N (10 kgf, 22.0 lbf) within 0.1 seconds and keep depressing the brake pedal with the same amount of force for 1 second.
Check that the ABS warning light stays on for 3 seconds.
Confirm that the ABS warning light comes on.
While the ABS warning light stays on, continue to depress the brake pedal with a force of 98 N (10 kgf, 22.0 lbf) or more.
The ABS warning light comes on for 3 seconds every time the preceding brake pedal operation is performed.
Speed Sensor Check
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds.
The sensor check may not complete if wheelspin occurs.
The ABS warning light comes on immediately if a malfunction is detected during the speed sensor check.
The speed sensor check may not complete if the speed sensor check is started while turning the steering wheel or spinning the wheels.
After the ABS warning light goes off, if vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
Check that the ABS warning light goes off.
The ABS warning light goes off when the sensor check has completed.
The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor check.
Stop the vehicle.
When the sensor check has completed, the ABS warning light goes off while the vehicle is being driven, and blinks in the Test Mode pattern while the vehicle is stopped.
If the sensor check has not completed, the ABS warning light will blink while the vehicle is being driven and the ABS will not operate.
Check the VSC sensor.
Check that the slip indicator light is blinking in the Test Mode pattern before performing the following VSC sensor check.
Yaw Rate Sensor Zero Point Check
Check that the shift lever is in P (for Continuously Variable Transaxle).
Check that the shift lever is in neutral and the parking brake is applied (for Manual Transaxle).
Keep the vehicle stationary on a level surface for 5 seconds or more after the ignition switch is turned to ON.
VSC OFF Switch Check
Press the VSC OFF switch.
Check that the VSC OFF indicator light comes on.
Press the VSC OFF switch again.
End of Sensor Check
If the sensor checks have completed, the ABS warning light blinks in the Test Mode pattern when the vehicle is stopped and the ABS warning light goes off while the vehicle is being driven.
If the sensor checks have not completed, the ABS warning light will blink while the vehicle is being driven and the ABS will not operate.
Reading Sensor Check DTCs
Read the DTCs by following the GTS screen.
If only DTCs other than Test Mode sensor check DTCs are displayed, repair the malfunctions and clear the DTCs.
If Test Mode sensor check DTCs and other DTCs are displayed or if only Test Mode sensor check DTCs are displayed, repair the malfunctions, clear the DTCs, and perform Test Mode inspection again.
See "Sensor Check DTCs".
Turn the ignition switch off and disconnect the GTS.
Sensor Check DTCs
| DTC No. | Detection Item | Trouble Area |
|---|---|---|
| C1271 | Low Output Signal of Front Speed Sensor RH | Front speed sensor and speed sensor rotor RH (Front axle hub sub-assembly RH) |
| C1272 | Low Output Signal of Front Speed Sensor LH | Front speed sensor and speed sensor rotor LH (Front axle hub sub-assembly LH) |
| C1273 | Low Output Signal of Rear Speed Sensor RH | ·
Rear speed sensor RH (rear axle hub and bearing assembly RH) ·
Sensor installation ·
Rear speed sensor rotor RH (rear axle hub and bearing assembly RH) |
| C1274 | Low Output Signal of Rear Speed Sensor LH | ·
Rear speed sensor LH (rear axle hub and bearing assembly LH) ·
Sensor installation ·
Rear speed sensor rotor LH (rear axle hub and bearing assembly LH) |
| C1275 | Abnormal Change in Output Signal of Front Speed Sensor RH | Front speed sensor and speed sensor rotor RH (Front axle hub sub-assembly RH) |
| C1276 | Abnormal Change in Output Signal of Front Speed Sensor LH | Front speed sensor and speed sensor rotor LH (Front axle hub sub-assembly LH) |
| C1277 | Abnormal Change in Output Signal of Rear Speed Sensor RH | Rear speed sensor rotor RH (rear axle hub and bearing assembly RH) |
| C1278 | Abnormal Change in Output Signal of Rear Speed Sensor LH | Rear speed sensor rotor LH (rear axle hub and bearing assembly LH) |
| C1279 | Acceleration Sensor Output Voltage Malfunction | ·
Sensor installation ·
Yaw rate and acceleration sensor (airbag ECU assembly) |
| C1281 | Master Cylinder Pressure Sensor Output Malfunction | ·
Stop light switch assembly ·
Master cylinder pressure sensor (brake actuator assembly) |
| DTC No. | Detection Item | Trouble Area |
|---|---|---|
| C1473 | Yaw Rate Sensor Malfunction | Yaw rate and acceleration sensor (airbag ECU assembly) |
The codes in this table are output only in Test Mode (signal check).
SENSOR CHECK USING TEST MODE (SIGNAL CHECK) (When Using SST Check Wire) (for TMMIN Made)
If the ignition switch is turned from ON to ACC or off during Test Mode (signal check), DTCs recorded during the sensor check will be cleared.
During Test Mode (signal check), the skid control ECU (brake actuator assembly) records all DTCs detected in the sensor check. By performing Test Mode (signal check), the codes are cleared as the normal condition for each item is confirmed. The remaining codes are the codes where an abnormality was found.
Procedure to enter Test Mode
Turn the ignition switch off.
Check that the steering wheel is centered.
Apply the parking brake.
Check that the shift lever is in P (for Continuously Variable Transaxle).
Check that the shift lever is in neutral and the parking brake is applied (for Manual Transaxle).
| *a | Front view of DLC3 |
Using SST, connect terminals TS and CG of the DLC3.
Turn the ignition switch to ON.
Check that the ABS warning and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.
If the ABS warning and slip indicator lights do not blink, inspect the TS and CG terminal circuit and ABS warning and slip indicator light circuits.
Check the ABS sensors.
Check that the ABS warning light is blinking in the Test Mode pattern before performing the following ABS sensor checks.
Acceleration Sensor Check
Keep the vehicle stationary on a level surface for 1 second or more.
The acceleration sensor check can be performed by following the master cylinder pressure sensor check procedure below.
Master Cylinder Pressure Sensor Check
Keep the vehicle stationary without the brake pedal depressed for 1 second or more. After that, depress the brake pedal quickly and strongly with a force of more than 98 N (10 kgf, 22.0 lbf) within 0.1 seconds and keep depressing the brake pedal with the same amount of force for 1 second.
Check that the ABS warning light stays on for 3 seconds.
Confirm that the ABS warning light comes on.
While the ABS warning light stays on, continue to depress the brake pedal with a force of 98 N (10 kgf, 22.0 lbf) or more.
The ABS warning light comes on for 3 seconds every time the preceding brake pedal operation is performed.
Speed Sensor Check
Drive the vehicle straight-ahead.
Accelerate the vehicle to a speed of 45 km/h (28 mph) or more for several seconds.
The sensor check may not complete if wheelspin occurs.
The ABS warning light comes on immediately if a malfunction is detected during the speed sensor check.
The speed sensor check may not complete if the speed sensor check is started while turning the steering wheel or spinning the wheels.
After the ABS warning light goes off, if vehicle speed exceeds 80 km/h (50 mph), a sensor check code will be stored again. Decelerate or stop the vehicle before the speed reaches 80 km/h (50 mph).
Check that the ABS warning light goes off.
The ABS warning light goes off when the sensor check has completed.
The ABS warning light comes on immediately after a malfunction has been detected during the speed sensor check.
Stop the vehicle.
When the sensor check has completed, the ABS warning light goes off while the vehicle is being driven, and blinks in the Test Mode pattern while the vehicle is stopped.
If the sensor check has not completed, the ABS warning light will blink while the vehicle is being driven and the ABS will not operate.
Check the VSC sensor.
Check that the slip indicator light is blinking in the Test Mode pattern before performing the following VSC sensor check.
Yaw Rate Sensor Zero Point Check
Check that the shift lever is in P (for Continuously Variable Transaxle).
Check that the shift lever is in neutral and the parking brake is applied (for Manual Transaxle).
Keep the vehicle stationary on a level surface for 5 seconds or more after the ignition switch is turned to ON.
VSC OFF Switch Check
Press the VSC OFF switch.
Check that the VSC OFF indicator light comes on.
Press the VSC OFF switch again.
End of Sensor Check
If the sensor checks have completed, the ABS warning light blinks in the Test Mode pattern when the vehicle is stopped and the ABS warning light goes off while the vehicle is being driven.
If the sensor checks have not completed, the ABS warning light will blink while the vehicle is being driven and the ABS will not operate.
| *a | Front view of DLC3 |
Reading Sensor Check DTCs
Using SST, connect terminals TC and CG of the DLC3.
Count the number of blinks of the ABS warning and slip indicator lights.
How to read DTCs:
Diagnostic trouble codes are represented by the number of blinks of a warning light. For example, code 21 would be shown by 2 blinks, a pause of 1.5 seconds, and then 1 blink.
If one code is detected:
The light repeats the same code after a pause of 4 seconds.
If multiple codes are detected:
The light outputs one code after another with a 2.5-second pause between each code.
When all codes have been output, there is a 4-second pause and then the light begins to output the codes again.
If only DTCs other than Test Mode sensor check DTCs are displayed, repair the malfunctions and clear the DTCs.
If Test Mode sensor check DTCs and other DTCs are displayed or if only Test Mode sensor check DTCs are displayed, repair the malfunctions, clear the DTCs, and perform Test Mode inspection again.
If more than 1 malfunction is detected at the same time, the lowest numbered code will be displayed first.
See "Sensor Check DTCs".
After performing the check, disconnect SST from terminals TS and CG, and TC and CG of the DLC3, and turn the ignition switch off.
Turn the ignition switch to ON to cancel Test Mode.
If the ignition switch is not turned off and back to ON after SST is removed from the DLC3, the previous Test Mode will continue.
If the ignition switch is turned back to ON with terminals TS and CG connected, the previous Test Mode will continue.
Sensor Check DTCs
| DTC No. | Detection Item | Trouble Area |
|---|---|---|
| 71 | Low Output Signal of Front Speed Sensor RH | Front speed sensor and speed sensor rotor RH (Front axle hub sub-assembly RH) |
| 72 | Low Output Signal of Front Speed Sensor LH | Front speed sensor and speed sensor rotor LH (Front axle hub sub-assembly LH) |
| 73 | Low Output Signal of Rear Speed Sensor RH | ·
Rear speed sensor RH (rear axle hub and bearing assembly RH) ·
Sensor installation ·
Rear speed sensor rotor RH (rear axle hub and bearing assembly RH) |
| 74 | Low Output Signal of Rear Speed Sensor LH | ·
Rear speed sensor LH (rear axle hub and bearing assembly LH) ·
Sensor installation ·
Rear speed sensor rotor LH (rear axle hub and bearing assembly LH) |
| 75 | Abnormal Change in Output Signal of Front Speed Sensor RH | Front speed sensor and speed sensor rotor RH (Front axle hub sub-assembly RH) |
| 76 | Abnormal Change in Output Signal of Front Speed Sensor LH | Front speed sensor and speed sensor rotor LH (Front axle hub sub-assembly LH) |
| 77 | Abnormal Change in Output Signal of Rear Speed Sensor RH | Rear speed sensor rotor RH (rear axle hub and bearing assembly RH) |
| 78 | Abnormal Change in Output Signal of Rear Speed Sensor LH | Rear speed sensor rotor LH (rear axle hub and bearing assembly LH) |
| 79 | Acceleration Sensor Output Voltage Malfunction | ·
Sensor installation ·
Yaw rate and acceleration sensor (airbag ECU assembly) |
| 81 | Master Cylinder Pressure Sensor Output Malfunction | ·
Stop light switch assembly ·
Master cylinder pressure sensor (brake actuator assembly) |
| DTC No. | Detection Item | Trouble Area |
|---|---|---|
| 71 | Yaw Rate Sensor Malfunction | Yaw rate and acceleration sensor (airbag ECU assembly) |
The codes in this table are output only in Test Mode (signal check).