TERMINALS OF ECU (for TMMIN Made)
| *a | Component without harness connected
(Skid Control ECU (Brake Actuator Assembly)) |
| Terminal No. (Symbol) | Terminal Description |
|---|---|
| 1 (GND1) | Skid control ECU ground |
| 2 (STP) | Stop light switch input |
| 4 (RL-) | Rear wheel speed LH (-) signal input |
| 5 (RL+) | Rear wheel speed LH (+) power supply output |
| 6 (FR-) | Front wheel speed RH (-) signal input |
| 7 (FR+) | Front wheel speed RH (+) power supply output |
| 11 (SP1) | Speed signal output for speedometer |
| 12 (+BS) | Solenoid relay power supply |
| 13 (GND2) | Pump motor ground |
| 14 (CANL) | CAN communication line L |
| 16 (RR-) | Rear wheel speed RH (-) signal input |
| 17 (RR+) | Rear wheel speed RH (+) power supply output |
| 18 (FL-) | Front wheel speed LH (-) signal input |
| 19 (FL+) | Front wheel speed LH (+) power supply output |
| 24 (BM) | Motor relay power supply |
| 25 (CANH) | CAN communication line H |
| 30 (CSW) | VSC OFF switch input |
| 33 (TS) | Sensor diagnosis check input |
| 34 (IG1) | ECU power supply |
TERMINALS OF ECU (for TMT Made)
| *a | Component without harness connected
(Skid Control ECU (Brake Actuator Assembly)) |
| Terminal No. (Symbol) | Terminal Description |
|---|---|
| 1 (GND1) | Skid control ECU ground |
| 2 (STP) | Stop light switch input |
| 4 (RL-) | Rear wheel speed LH (-) signal input |
| 5 (RL+) | Rear wheel speed LH (+) power supply output |
| 6 (FR-) | Front wheel speed RH (-) signal input |
| 7 (FR+) | Front wheel speed RH (+) power supply output |
| 11 (SP1) | Speed signal output for speedometer |
| 12 (+BS) | Solenoid relay power supply |
| 13 (GND2) | Pump motor ground |
| 14 (CANL) | CAN communication line L |
| 16 (RR-) | Rear wheel speed RH (-) signal input |
| 17 (RR+) | Rear wheel speed RH (+) power supply output |
| 18 (FL-) | Front wheel speed LH (-) signal input |
| 19 (FL+) | Front wheel speed LH (+) power supply output |
| 24 (BM) | Motor relay power supply |
| 25 (CANH) | CAN communication line H |
| 27 (EXI3)*1 | Back-up light switch assembly input |
| 30 (CSW) | VSC OFF switch input |
| 34 (IG1) | ECU power supply |
*1: for Manual Transaxle
TERMINAL INSPECTION (for TMMIN Made)
Disconnect the connector and measure the voltage or resistance on the wire harness side.
| *A | for Manual Transaxle | *B | for Continuously Variable Transaxle |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
- | - |
Voltage cannot be measured with the connector connected to the brake actuator assembly (skid control ECU) as the connector is watertight.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A48-1 (GND1) - Body ground | W-B - Body ground | Skid control ECU ground | Always | Below 1 Ω |
| A48-2 (STP) - Body ground | GR - Body ground | Stop light switch input | Stop light switch ON → OFF
(Brake pedal depressed → released) |
7.5 to 14 V → Below 1.5 V |
| A48-12 (+BS) - Body ground | W - Body ground | Solenoid relay power supply | Always | 11 to 14 V |
| A48-13 (GND2) - Body ground | W-B - Body ground | Pump motor ground | Always | Below 1 Ω |
| A48-24 (BM) - Body ground | B - Body ground | Motor relay power supply | Always | 11 to 14 V |
| A48-25 (CANH) - A48-14(CANL) | L - W | CAN bus | Ignition switch off | 54 to 69 Ω |
| A48-30 (CSW) - Body ground | L - Body ground | VSC OFF switch input | VSC OFF switch held ON → OFF (Not pressed) | Below 25 Ω → 10 kΩ or higher |
| A48-34 (IG1) - Body ground | L - Body ground | ECU power supply | Ignition switch ON | 11 to 14 V |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A49-1 (GND1) - Body ground | W-B - Body ground | Skid control ECU ground | Always | Below 1 Ω |
| A49-2 (STP) - Body ground | GR - Body ground | Stop light switch input | Stop light switch ON → OFF
(Brake pedal depressed → released) |
7.5 to 14 V → Below 1.5 V |
| A49-12 (+BS) - Body ground | W - Body ground | Solenoid relay power supply | Always | 11 to 14 V |
| A49-13 (GND2) - Body ground | W-B - Body ground | Pump motor ground | Always | Below 1 Ω |
| A49-24 (BM) - Body ground | B - Body ground | Motor relay power supply | Always | 11 to 14 V |
| A49-25 (CANH) - A49-14 (CANL) | L - W | CAN bus | Ignition switch off | 54 to 69 Ω |
| A49-30 (CSW) - Body ground | L - Body ground | VSC OFF switch input | VSC OFF switch held ON → OFF (Not pressed) | Below 25 Ω → 10 kΩ or higher |
| A49-34 (IG1) - Body ground | L - Body ground | ECU power supply | Ignition switch ON | 11 to 14 V |
TERMINAL INSPECTION (for TMT Made)
Disconnect the connector and measure the voltage or resistance on the wire harness side.
| *A | except LHD with Continuously Variable Transaxle | *B | for LHD with Continuously Variable Transaxle |
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly)) |
- | - |
Voltage cannot be measured with the connector connected to the brake actuator assembly (skid control ECU) as the connector is watertight.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
|
*1: for Manual Transaxle |
||||
| A48-1 (GND1) - Body ground | W-B - Body ground | Skid control ECU ground | Always | Below 1 Ω |
| A48-2 (STP) - Body ground | SB - Body ground | Stop light switch input | Stop light switch ON → OFF
(Brake pedal depressed → released) |
7.5 to 14 V → Below 1.5 V |
| A48-12 (+BS) - Body ground | W - Body ground | Solenoid relay power supply | Always | 11 to 14 V |
| A48-13 (GND2) - Body ground | W-B - Body ground | Pump motor ground | Always | Below 1 Ω |
| A48-24 (BM) - Body ground | B - Body ground | Motor relay power supply | Always | 11 to 14 V |
| A48-25 (CANH) - A48-14(CANL) | L - W | CAN bus | Ignition switch off | 54 to 69 Ω |
| A48-30 (CSW) - Body ground | P - Body ground | VSC OFF switch input | VSC OFF switch held ON → OFF (Not pressed) | Below 25 Ω → 10 kΩ or higher |
| A48-34 (IG1) - Body ground | L - Body ground | ECU power supply | Ignition switch ON | 11 to 14 V |
| A48-27 (EXI3)*1 - Body ground | GR - Body ground | Back-up light switch assembly input | Shift lever not in R → Shift lever in R | Below 1.5 V → 7.5 to 14 V |
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| A49-1 (GND1) - Body ground | W-B - Body ground | Skid control ECU ground | Always | Below 1 Ω |
| A49-2 (STP) - Body ground | SB - Body ground | Stop light switch input | Stop light switch ON → OFF
(Brake pedal depressed → released) |
7.5 to 14 V → Below 1.5 V |
| A49-12 (+BS) - Body ground | W - Body ground | Solenoid relay power supply | Always | 11 to 14 V |
| A49-13 (GND2) - Body ground | W-B - Body ground | Pump motor ground | Always | Below 1 Ω |
| A49-24 (BM) - Body ground | B - Body ground | Motor relay power supply | Always | 11 to 14 V |
| A49-25 (CANH) - A49-14 (CANL) | L - W | CAN bus | Ignition switch off | 54 to 69 Ω |
| A49-30 (CSW) - Body ground | P - Body ground | VSC OFF switch input | VSC OFF switch held ON → OFF (Not pressed) | Below 25 Ω → 10 kΩ or higher |
| A49-34 (IG1) - Body ground | L - Body ground | ECU power supply | Ignition switch ON | 11 to 14 V |